Bug#391384: linux-image-2.6.18-1-686: Compaq Proliant DL380 fails to boot
All,
On 10/10/06, Dmitry Semyonov <linulin@gmail.com> wrote:
On 10/9/06, dann frazier <dannf@debian.org> wrote:
> > On Sun, 2006-10-08 at 21:16 -0600, Grant Grundler wrote:
> > > I didn't know Compaq used two different 53[cC]510 parts.
> > > Patch below adds the same tweak to the 0x0010 device ID.
[...]
> Are you able to test this fix?
Of course! Will do tomorrow.
The patched kernel booted successfully with the workaround disabled.
Here is the log:
Linux version 2.6.18 () (root@mon) (gcc version 4.1.2 20060901
(prerelease) (Debian 4.1.1-13)) #1 SMP Tue Oct 10 03:59:26 PDT 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fffc000 (usable)
BIOS-e820: 000000003fffc000 - 0000000040000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f4ff0
DMI 2.3 present.
ACPI: PM-Timer IO Port: 0x240
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:8 APIC version 17
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 6:8 APIC version 17
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 17, address 0xfec00000, GSI 0-34
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
Detected 797.544 MHz processor.
Built 1 zonelists. Total pages: 262140
Kernel command line: root=/dev/ida/c0d0p1 ro console=tty0 console=ttyS0,38400n8
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1031832k/1048560k available (1534k kernel code, 16044k
reserved, 575k data, 196k init, 131056k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1595.97 BogoMIPS (lpj=3191958)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
CPU0: Intel Pentium III (Coppermine) stepping 03
SMP alternatives: switching to SMP code
Booting processor 1/0 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 1595.10 BogoMIPS (lpj=3190213)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Pentium III (Coppermine) stepping 03
Total of 2 processors activated (3191.08 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
migration_cost=938
checking if image is initramfs... it is
Freeing initrd memory: 4359k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0084, last bus=3
PCI: Using configuration type 1
Setting up standard PCI resources
mtrr: your CPUs had inconsistent fixed MTRR settings
mtrr: probably your BIOS does not setup all CPUs.
mtrr: corrected configuration.
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Firmware left 0000:00:02.0 e100 interrupts enabled, disabling
ACPI: PCI Root Bridge [PCI1] (0000:03)
ACPI: Resource is not an IRQ entry
ACPI: PCI Interrupt Link [FAKE] (IRQs) *0, disabled.
ACPI: PCI Interrupt Link [INA0] (IRQs 5 10 11 15) *0, disabled.
ACPI: PCI Interrupt Link [INA1] (IRQs 5 10 11 15) *0, disabled.
ACPI: PCI Interrupt Link [INA2] (IRQs 5 10 11 15) *0, disabled.
ACPI: PCI Interrupt Link [INA3] (IRQs 5 10 *11 15)
ACPI: PCI Interrupt Link [INA4] (IRQs 5 10 11 15) *0, disabled.
ACPI: PCI Interrupt Link [INA5] (IRQs 5 10 11 15) *0, disabled.
ACPI: PCI Interrupt Link [ITR0] (IRQs 5 10 11 15) *0, disabled.
ACPI: PCI Interrupt Link [ITR1] (IRQs 5 *10 11 15)
ACPI: PCI Interrupt Link [ITR2] (IRQs 5 10 11 15) *0, disabled.
ACPI: PCI Interrupt Link [ITR3] (IRQs *5 10 11 15)
ACPI: PCI Interrupt Link [INB0] (IRQs 5 10 11 15) *0, disabled.
ACPI: PCI Interrupt Link [INB1] (IRQs 5 10 11 15) *0, disabled.
ACPI: PCI Interrupt Link [INB2] (IRQs 5 10 11 15) *0, disabled.
ACPI: PCI Interrupt Link [INB3] (IRQs 5 10 11 15) *0, disabled.
ACPI: PCI Interrupt Link [INB4] (IRQs 5 10 11 15) *0, disabled.
ACPI: PCI Interrupt Link [INB5] (IRQs 5 10 11 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Device 0000:00:00.0 not found by BIOS
PCI: Device 0000:00:00.1 not found by BIOS
PCI: Device 0000:00:0f.0 not found by BIOS
pnp: 00:01: ioport range 0xf50-0xf58 has been reserved
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1160488254.432:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Starting balanced_irq
Using IPI No-Shortcut mode
ACPI: (supports<6>Time: tsc clocksource has been installed.
S0 S4 S5)
Freeing unused kernel memory: 196k freed
input: AT Translated Set 2 keyboard as /class/input/input0
Loading, please wait...
Begin: Loading essential drivers... ...
Done.
Begin: Running /scripts/init-premount ...
ACPI: Thermal Zone [THM0] (8 C)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 17 (level, low) -> IRQ 177
e100: eth0: e100_probe: addr 0xc3fff000, irq 177, MAC addr 00:02:A5:0A:57:CF
Compaq SMART2 Driver (v 2.6.0)
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 19 (level, low) -> IRQ 185
cpqarray: Finding drives on ida0 (Integrated Array)
cpqarray ida/c0d0: blksz=512 nr_blks=35520480
ida/c0d0:<6>natsemi dp8381x driver, version 2.0, June 27, 2006
originally by Donald Becker <becker@scyld.com>
http://www.scyld.com/network/natsemi.html
2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
p1 p2 < p5 >
ACPI: PCI Interrupt 0000:03:04.0[A] -> GSI 27 (level, low) -> IRQ 193
natsemi eth1: NatSemi DP8381[56] at 0xc6fff000 (0000:03:04.0),
00:0f:b5:fa:bd:2d, IRQ 193, port TP.
SvrWks OSB4: IDE controller at PCI slot 0000:00:0f.1
SvrWks OSB4: chipset revision 0
SvrWks OSB4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x2c00-0x2c07, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x2c08-0x2c0f, BIOS settings: hdc:pio, hdd:pio
hda: CD-224E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ATAPI 24X CD-ROM drive, 512kB Cache
Uniform CD-ROM driver Revision: 3.20
Done.
Begin: Mounting root file system... ...
Begin: Running /scripts/local-top ...
Done.
Begin: Running /scripts/local-premount ...
kinit: name_to_dAttempting manual resume
ev_t(/dev/ida/c0d0p5) = ida!c0d0p5(72,5)
kinit: trying to resume from /dev/ida/c0d0p5
kinit: No resume image, doing normal boot...
Done.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Begin: Running /scripts/local-bottom ...
Done.
Done.
Begin: Running /scripts/init-bottom ...
Done.
INIT: version 2.86 booting
Setting hostname to 'mon'...done.
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...Linux agpgart interface
v0.101 (c) Dave Jones
agpgart: unable to determine aperture size.
agpgart: agp_backend_initialize() failed.
agpgart-serverworks: probe of 0000:00:00.0 failed with error -22
agpgart: unable to determine aperture size.
agpgart: agp_backend_initialize() failed.
agpgart-serverworks: probe of 0000:00:00.1 failed with error -22
Floppy drive(s): fd0 is 1.44M
input: PC Speaker as /class/input/input1
FDC 0 is a National Semiconductor PC87306
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
piix4_smbus 0000:00:0f.0: Found 0000:00:0f.0 device
piix4_smbus 0000:00:0f.0: SMB base address uninitialized - upgrade
BIOS or use force_addr=0xaddr
done.
Setting parameters of disc: (none).
Activating swap:swapon on /dev/iAdding 755012k swap on
/dev/ida/c0d0p5. Priority:-1 extents:1 across:755012k
da/c0d0p5
.
Will now check root file system:fsck 1.39 (29-May-2006)
[/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/ida/c0d0p1
e2fsck 1.39 (29-May-2006)
/: clean, 93840/2125760 files, 701086/4251192 blocks
.
EXT3 FS on ida/c0d0p1, internal journal
Setting the system clock..
System Clock set. Local time: Tue Oct 10 13:51:07 UTC 2006.
Cleaning up ifupdown....
Loading modules...
ide-cd
ide-detect
FATAL: Module ide_detect not found.
ide-disk
psmouse
All modules loaded.
Setting the system clock again..
System Clock set. Local time: Tue Oct 10 13:51:08 UTC 2006.
Loading device-mapper supportdevice-mapper: ioctl: 4.7.0-ioctl
(2006-06-24) initialised: dm-devel@redhat.com
.
Will now check all file systems.
fsck 1.39 (29-May-2006)
Checking all file systems.
Done checking file systems.
A log is being saved in /var/log/fsck/checkfs if that location is writable.
Setting kernel variables...done.
Will now mount local filesystems:.
Will now activate swapfile swap:done.
Detecting hardware...Discovered hardware for these modules: e100
natsemi serverworks cpqarray ide_scsi
* Skipping already loaded module e100.
* Skipping already loaded module natsemi.
* Skipping already loaded module serverworks.
* Skipping already loaded module cpqarray.
* Skipping unavailable/built-in ide_scsi module.
Cleaning /tmp...done.
Cleaning /var/run...done.
Cleaning /var/lock...done.
Running 0dns-down to make sure resolv.conf is ok...done.
Setting up networking....
* /etc/network/options is deprecated.
Setting up IP spoofing protection...done (rp_filter).
Configuring network interfaces...e100: eth0: e100_watchdog: link up,
100Mbps, half-duplex
eth1: DSPCFG accepted after 0 usec.
eth1: link up.
eth1: Setting full-duplex based on negotiated link capability.
done.
Starting portmap daemon....
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
Setting console screen modes and fonts.
Initializing random number generator...done.
Recovering nvi editor sessions...none found.
INIT: Entering runlevel: 2
--
...Bye..Dmitry.
Reply to: