Re: Impossible to find CD-ROM using sata drivers
Sorry, dmesg was missing :
dmesg
Linux version 2.6.14-2-686 (Debian 2.6.14-4) (fs@debian.org) (gcc
version 4.0.3 20051111 (prerelease) (Debian 4.0.2-4)) #1 Sat Nov 26
13:10:11 UTC 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003ffd0000 (usable)
BIOS-e820: 000000003ffd0000 - 000000003ffde000 (ACPI data)
BIOS-e820: 000000003ffde000 - 0000000040000000 (ACPI NVS)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fed13000 - 00000000fed1a000 (reserved)
BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000ff780
On node 0 totalpages: 262096
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 32720 pages, LIFO batch:15
DMI 2.3 present.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: TEMPLATE Product ID: ETEMPLATE APIC at: 0xFEE00000
Processor #0 6:13 APIC version 20
I/O APIC #1 Version 32 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 1
Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
Built 1 zonelists
Kernel command line: root=/dev/sda1 ro acpi=off
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 1867.328 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1034548k/1048384k available (1875k kernel code, 13000k reserved,
536k data, 180k init, 130880k highmem)
Checking if this processor honours the WP bit even in supervisor mode...
Ok.
Calibrating delay using timer specific routine.. 3737.05 BogoMIPS
(lpj=1868526)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000
00000180 00000000 00000000
CPU: After vendor identify, caps: afe9fbff 00100000 00000000 00000000
00000180 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: After all inits, caps: afe9fbff 00100000 00000000 00000040 00000180
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
CPU: Intel(R) Pentium(R) M processor 1.86GHz stepping 08
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=0
checking if image is initramfs... it is
Freeing initrd memory: 1085k freed
softlockup thread 0 started up.
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=3
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f52a0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x625a, dseg 0xf0000
PnPBIOS: Missing SMALL_TAG_ENDDEP tag
PnPBIOS: 14 nodes reported by PnP BIOS; 14 recorded by driver
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2
Boot video device is 0000:03:00.0
PCI: Transparent bridge - 0000:00:1e.0
PCI: Discovered primary peer bus ff [IRQ]
PCI: Using IRQ router PIIX/ICH [8086/2641] at 0000:00:1f.0
PCI->APIC IRQ transform: 0000:00:01.0[A] -> IRQ 129
PCI->APIC IRQ transform: 0000:00:1b.0[A] -> IRQ 129
PCI->APIC IRQ transform: 0000:00:1d.0[A] -> IRQ 161
PCI->APIC IRQ transform: 0000:00:1d.1[B] -> IRQ 153
PCI->APIC IRQ transform: 0000:00:1d.2[C] -> IRQ 145
PCI->APIC IRQ transform: 0000:00:1d.3[D] -> IRQ 129
PCI->APIC IRQ transform: 0000:00:1d.7[A] -> IRQ 161
PCI->APIC IRQ transform: 0000:00:1f.2[B] -> IRQ 153
PCI->APIC IRQ transform: 0000:00:1f.3[B] -> IRQ 153
PCI->APIC IRQ transform: 0000:03:00.0[A] -> IRQ 129
PCI->APIC IRQ transform: 0000:01:03.0[A] -> IRQ 137
PCI->APIC IRQ transform: 0000:01:07.0[A] -> IRQ 153
PCI->APIC IRQ transform: 0000:01:0a.0[A] -> IRQ 145
PCI->APIC IRQ transform: 0000:01:0c.0[A] -> IRQ 153
pnp: 00:0a: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:0a: ioport range 0xcf8-0xcff could not be reserved
pnp: 00:0a: ioport range 0x480-0x4bf has been reserved
pnp: 00:0a: ioport range 0x800-0x87f has been reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: f4a00000-feafffff
PREFETCH window: bfe00000-dfefffff
PCI: Bus 2, cardbus bridge: 0000:01:03.0
IO window: 0000c000-0000c0ff
IO window: 0000c400-0000c4ff
PREFETCH window: 50000000-51ffffff
MEM window: 52000000-53ffffff
PCI: Bridge: 0000:00:1e.0
IO window: c000-dfff
MEM window: f4100000-f49fffff
PREFETCH window: bde00000-bfdfffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
audit: initializing netlink socket (disabled)
audit(1133467341.584:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: PS/2 Controller [PNP0303,PNP0f13] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.0.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard on isa0060/serio0
IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
TCP established hash table entries: 262144 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI Shortcut mode
Freeing unused kernel memory: 180k freed
mice: PS/2 mouse device common for all mice
SCSI subsystem initialized
libata version 1.12 loaded.
ata_piix version 1.04
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xFFA0 irq 14
ata1: dev 1 cfg 49:2f00 82:346b 83:7f09 84:6063 85:3469 86:3e09 87:6063
88:203f
ata1: dev 1 ATA, max UDMA/100, 156301488 sectors: lba48
ata1: dev 1 configured for UDMA/100
scsi0 : ata_piix
Vendor: ATA Model: FUJITSU MHT2080B Rev: 0000
Type: Direct-Access ANSI SCSI revision: 05
ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xFFA8 irq 15
ata2: dev 0 cfg 49:0f00 82:4218 83:5000 84:4000 85:4218 86:1000 87:4000
88:0407
ata2: dev 0 ATAPI, max UDMA/33
ata2(0): applying bridge limits
ata2: dev 0 configured for UDMA/33
scsi1 : ata_piix
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 < sda5 >
Attached scsi disk sda at scsi0, channel 0, id 1, lun 0
JFS: nTxBlock = 8095, nTxLock = 64766
Synaptics Touchpad, model: 1, fw: 6.2, id: 0xa0b1, caps:
0xa04713/0x20040a
input: SynPS/2 Synaptics TouchPad on isa0060/serio2
input: PC Speaker
usbcore: registered new driver usbfs
usbcore: registered new driver hub
hw_random: RNG not detected
Linux agpgart interface v0.101 (c) Dave Jones
Real Time Clock Driver v1.12
USB Universal Host Controller Interface driver v2.3
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 161, io base 0x0000e480
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
agpgart: Detected an Intel 915GM Chipset.
agpgart: AGP aperture is 256M @ 0x0
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 153, io base 0x0000e800
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 145, io base 0x0000e880
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 129, io base 0x0000ec00
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: irq 161, io mem 0xfebffc00
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec
2004
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
ieee80211_crypt: registered algorithm 'NULL'
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1313 $ Ben Collins <bcollins@debian.org>
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[145]
MMIO=[f49ff000-f49ff7ff] Max Packet=[2048]
r8169 Gigabit Ethernet driver 2.2LK loaded
eth0: Identified chip type is 'RTL8169s/8110s'.
eth0: RTL8169 at 0xf8ed6c00, 00:03:0d:36:cd:69, IRQ 153
PCI: Setting latency timer of device 0000:00:1b.0 to 64
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.0.0
ipw2200: Copyright(c) 2003-2004 Intel Corporation
Yenta: CardBus bridge found at 0000:01:03.0 [1584:3200]
Yenta: adjusting diagnostic: 40 -> 60
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:01:03.0, mfunc 0x000c1002, devctl 0x44
Yenta: ISA IRQ mask 0x0250, PCI irq 137
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0xc000 - 0xdfff
cs: IO port probe 0xc000-0xdfff: clean.
pcmcia: parent PCI bridge Memory window: 0xf4100000 - 0xf49fffff
pcmcia: parent PCI bridge Memory window: 0xbde00000 - 0xbfdfffff
ipw2200: Detected Intel PRO/Wireless 2915ABG Network Connection
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00030d49255fbcdb]
eth1394: $Rev: 1312 $ Ben Collins <bcollins@debian.org>
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
Adding 2650684k swap on /dev/sda5. Priority:-1 extents:1
across:2650684k
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for
Generic
usbcore: registered new driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
drivers/usb/serial/usb-serial.c: USB Serial support registered for
IPWireless converter
usbcore: registered new driver ipwtty
drivers/usb/serial/ipw.c: IPWireless tty driver v0.3
ieee80211_crypt: registered algorithm 'WEP'
ipw2200: Firmware error detected. Restarting.
pcmcia: Detected deprecated PCMCIA ioctl usage.
pcmcia: This interface will soon be removed from the kernel; please
expect breakage unless you upgrade to new tools.
pcmcia: see
http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for
details.
cs: IO port probe 0x100-0x4ff: excluding 0x370-0x377 0x3b0-0x3df
0x3f0-0x3f7
cs: IO port probe 0x800-0x8ff: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0xa00-0xaff: clean.
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0328b40(lo)
IPv6 over IPv4 tunneling driver
wifi: duplicate address detected!
wifi (WE) : Driver using old /proc/net/wireless support, please fix
driver !
st: Version 20050830, fixed bufsize 32768, s/g segs 256
Attached scsi generic sg0 at scsi0, channel 0, id 1, lun 0, type 0
Reply to: