Bug#333831: #333831 Debian BTS
Output of dmesg.
Boot was repeated with kernel option pci-routeirq, and then again with
pollirq, all behave similarly.
Will retry without ide-cd
dmesg 2.6.14-1 boot
00 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
CPU: Intel Celeron (Coppermine) stepping 03
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0c00)
checking if image is initramfs... it is
softlockup thread 0 started up.
Freeing initrd memory: 1072k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0200, last bus=1
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [PILA] (IRQs 1 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [PILB] (IRQs 1 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [PILC] (IRQs 1 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [PILD] (IRQs 1 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [PILE] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [PILF] (IRQs 1 3 4 5 6 7 9 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [PILG] (IRQs 1 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [PILH] (IRQs 1 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [PILI] (IRQs 1 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
PCI quirk: region f100-f13f claimed by ali7101 ACPI
PCI quirk: region f140-f15f claimed by ali7101 SMB
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller [EC0] (gpe 34)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
report
pnp: 00:09: ioport range 0xf100-0xf13f could not be reserved
pnp: 00:09: ioport range 0xf140-0xf15f has been reserved
pnp: 00:09: ioport range 0x1060-0x106f has been reserved
pnp: 00:09: ioport range 0x40b-0x40b has been reserved
PCI: Bridge: 0000:00:01.0
IO window: 7000-7fff
MEM window: 80100000-820fffff
PREFETCH window: disabled.
PCI: Bus 2, cardbus bridge: 0000:00:13.0
IO window: 00001400-000014ff
IO window: 00001800-000018ff
PREFETCH window: 20000000-21ffffff
MEM window: 22000000-23ffffff
PCI: Bus 6, cardbus bridge: 0000:00:13.1
IO window: 00001c00-00001cff
IO window: 00002000-000020ff
PREFETCH window: 24000000-25ffffff
MEM window: 26000000-27ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt Link [PILB] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:13.0[A] -> Link [PILB] -> GSI 11 (level,
low) -> IRQ 11
ACPI: PCI Interrupt 0000:00:13.1[A] -> Link [PILB] -> GSI 11 (level,
low) -> IRQ 11
Simple Boot Flag at 0x6e set to 0x1
audit: initializing netlink socket (disabled)
audit(1131809688.985:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
Activating ISA DMA hang workarounds.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 4, 65536 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI Shortcut mode
ACPI wakeup devices:
COM0 OZ68 OZ69 OBAU USB0 LID
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 180k freed
input: AT Translated Set 2 keyboard on isa0060/serio0
mice: PS/2 mouse device common for all mice
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ALI15X3: IDE controller at PCI slot 0000:00:10.0
ACPI: PCI Interrupt 0000:00:10.0[A]: no GSI - using IRQ 15
PCI: setting IRQ 15 as level-triggered
ALI15X3: chipset revision 195
ALI15X3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x6050-0x6057, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x6058-0x605f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: IBM-DJSA-205, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: MATSHITA CR-176, ATAPI CD/DVD-ROM drive
irq 15: nobody cared (try booting with the "irqpoll" option)
[<c013cd0a>] __report_bad_irq+0x2a/0xa0
[<c013c69d>] handle_IRQ_event+0x3d/0x70
[<c013ce27>] note_interrupt+0x87/0xf0
[<c013c779>] __do_IRQ+0xa9/0xc0
[<c01052f9>] do_IRQ+0x19/0x30
[<c0103b0a>] common_interrupt+0x1a/0x20
[<c012085e>] __do_softirq+0x2e/0xa0
[<c01208f6>] do_softirq+0x26/0x30
[<c01052fe>] do_IRQ+0x1e/0x30
[<c0103b0a>] common_interrupt+0x1a/0x20
[<c014007b>] generic_file_buffered_write+0x37b/0x700
[<c013c997>] setup_irq+0x87/0x110
[<c013cb9a>] request_irq+0xaa/0xd0
[<d0863350>] ide_intr+0x0/0x180 [ide_core]
[<d08677f1>] init_irq+0x1a1/0x410 [ide_core]
[<d0863350>] ide_intr+0x0/0x180 [ide_core]
[<d0867f2f>] hwif_init+0xdf/0x2b0 [ide_core]
[<d0867406>] probe_hwif_init_with_fixup+0x26/0x90 [ide_core]
[<d086aeba>] ide_setup_pci_device+0x8a/0xa0 [ide_core]
[<d086b021>] ide_scan_pcidev+0x41/0x70 [ide_core]
[<d086b0a8>] ide_scan_pcibus+0x58/0x110 [ide_core]
[<d0823005>] ide_generic_init+0x5/0x12 [ide_generic]
[<c0137181>] sys_init_module+0xc1/0x1a0
[<c01030c5>] syscall_call+0x7/0xb
handlers:
[<d0863350>] (ide_intr+0x0/0x180 [ide_core])
Disabling IRQ #15
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 9767520 sectors (5000 MB) w/384KiB Cache, CHS=10336/15/63, UDMA(33)
hda: cache flushes not supported
hda: hda1 hda2 < hda5 >
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
NET: Registered protocol family 1
Adding 239044k swap on /dev/hda5. Priority:-1 extents:1 across:239044k
EXT3 FS on hda1, internal journal
ide-cd: cmd 0x5a timed out
hdc: lost interrupt
irq 15: nobody cared (try booting with the "irqpoll" option)
[<c013cd0a>] __report_bad_irq+0x2a/0xa0
[<c013c69d>] handle_IRQ_event+0x3d/0x70
[<c013ce27>] note_interrupt+0x87/0xf0
[<c013c779>] __do_IRQ+0xa9/0xc0
[<d08ffa60>] cdrom_pc_intr+0x0/0x2a0 [ide_cd]
[<c01052f9>] do_IRQ+0x19/0x30
[<c0103b0a>] common_interrupt+0x1a/0x20
[<d08ffa60>] cdrom_pc_intr+0x0/0x2a0 [ide_cd]
[<d0863134>] ide_timer_expiry+0xc4/0x220 [ide_core]
[<d0863070>] ide_timer_expiry+0x0/0x220 [ide_core]
[<c0124ade>] run_timer_softirq+0xce/0x1b0
[<c0120872>] __do_softirq+0x42/0xa0
[<c01208f6>] do_softirq+0x26/0x30
[<c01052fe>] do_IRQ+0x1e/0x30
[<c0103b0a>] common_interrupt+0x1a/0x20
[<c0101030>] default_idle+0x0/0x30
[<c0101056>] default_idle+0x26/0x30
[<c01010d3>] cpu_idle+0x33/0x50
[<c03468ba>] start_kernel+0x17a/0x1e0
[<c03463e0>] unknown_bootoption+0x0/0x1f0
handlers:
[<d0863350>] (ide_intr+0x0/0x180 [ide_core])
Disabling IRQ #15
ide-cd: cmd 0x5a timed out
hdc: lost interrupt
Real Time Clock Driver v1.12
Generic RTC Driver v1.07
apm: BIOS version 1.2 Flags 0x0f (Driver version 1.16ac)
apm: overridden by ACPI.
ACPI: PCI Interrupt Link [PILH] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [PILH] -> GSI 10 (level,
low) -> IRQ 10
ACPI: PCI Interrupt 0000:00:13.0[A] -> Link [PILB] -> GSI 11 (level,
low) -> IRQ 11
Yenta: CardBus bridge found at 0000:00:13.0 [1025:1010]
Yenta O2: res at 0x94/0xD4: ea/00
Yenta O2: enabling read prefetch/write burst
Yenta: ISA IRQ mask 0x0038, PCI irq 11
Socket status: 30000006
ACPI: PCI Interrupt 0000:00:13.1[A] -> Link [PILB] -> GSI 11 (level,
low) -> IRQ 11
Yenta: CardBus bridge found at 0000:00:13.1 [1025:1010]
Yenta: ISA IRQ mask 0x0038, PCI irq 11
Socket status: 30000410
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [PILI] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [PILI] -> GSI 11 (level,
low) -> IRQ 11
ohci_hcd 0000:00:14.0: OHCI Host Controller
ohci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:14.0: irq 11, io mem 0x82400000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
NET: Registered protocol family 15
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected ALi M???? chipset
agpgart: AGP aperture is 64M @ 0xe0000000
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
input: PC Speaker
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
Synaptics Touchpad, model: 1, fw: 4.6, id: 0x925ea1, caps: 0x80471b/0x0
input: SynPS/2 Synaptics TouchPad on isa0060/serio1
pcmcia: Detected deprecated PCMCIA ioctl usage.
pcmcia: This interface will soon be removed from the kernel; please
expect breakage unless you upgrade to new tools.
pcmcia: see
http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details.
cs: IO port probe 0x100-0x4ff: excluding 0x200-0x207 0x220-0x22f
0x330-0x337 0x388-0x38f 0x480-0x48f 0x4d0-0x4d7
cs: IO port probe 0x100-0x4ff: excluding 0x200-0x207 0x220-0x22f
0x330-0x337 0x388-0x38f 0x480-0x48f 0x4d0-0x4d7
cs: IO port probe 0x800-0x8ff: clean.
cs: IO port probe 0x800-0x8ff: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
orinoco 0.15rc2 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel
Roskin <proski@gnu.org>, et al)
orinoco_cs 0.15rc2 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel
Roskin <proski@gnu.org>, et al)
eth0: Hardware identity 0001:0001:0004:0000
eth0: Station identity 001f:0001:0008:000a
eth0: Firmware determined as Lucent/Agere 8.10
eth0: Ad-hoc demo mode supported
eth0: IEEE standard IBSS ad-hoc mode supported
eth0: WEP supported, 104-bit key
eth0: MAC address 00:02:2D:0D:27:84
eth0: Station name "HERMES I"
eth0: ready
eth0: index 0x01: Vcc 5.0, irq 3, io 0x0100-0x013f
eth0: New link status: Connected (0001)
NET: Registered protocol family 17
ide-cd: cmd 0x5a timed out
hdc: lost interrupt
irq 15: nobody cared (try booting with the "irqpoll" option)
[<c013cd0a>] __report_bad_irq+0x2a/0xa0
[<c013c69d>] handle_IRQ_event+0x3d/0x70
[<c013ce27>] note_interrupt+0x87/0xf0
[<c013c779>] __do_IRQ+0xa9/0xc0
[<d08ffa60>] cdrom_pc_intr+0x0/0x2a0 [ide_cd]
[<c01052f9>] do_IRQ+0x19/0x30
[<c0103b0a>] common_interrupt+0x1a/0x20
[<d08ffa60>] cdrom_pc_intr+0x0/0x2a0 [ide_cd]
[<d0863134>] ide_timer_expiry+0xc4/0x220 [ide_core]
[<d0863070>] ide_timer_expiry+0x0/0x220 [ide_core]
[<c0124ade>] run_timer_softirq+0xce/0x1b0
[<c0120872>] __do_softirq+0x42/0xa0
[<c01208f6>] do_softirq+0x26/0x30
[<c01052fe>] do_IRQ+0x1e/0x30
[<c0103b0a>] common_interrupt+0x1a/0x20
[<d0862503>] ide_map_sg+0x93/0xc0 [ide_core]
[<d086b31c>] ide_build_sglist+0x3c/0xc0 [ide_core]
[<d086b3dd>] ide_build_dmatable+0x3d/0x190 [ide_core]
[<d086b867>] ide_dma_setup+0x37/0xe0 [ide_core]
[<d084b529>] __ide_do_rw_disk+0x399/0x590 [ide_disk]
[<d08640eb>] ide_wait_stat+0x8b/0x150 [ide_core]
[<d0862ab0>] start_request+0x2b0/0x300 [ide_core]
[<d0862e38>] ide_do_request+0x308/0x400 [ide_core]
[<d0862f54>] do_ide_request+0x24/0x30 [ide_core]
[<c0236990>] generic_unplug_device+0x10/0x20
[<c0162856>] block_sync_page+0x36/0x50
[<c013d3f2>] sync_page+0x32/0x50
[<c02c1231>] __wait_on_bit_lock+0x41/0x70
[<c013d3c0>] sync_page+0x0/0x50
[<c013dc2d>] __lock_page+0x6d/0x80
[<c0130140>] wake_bit_function+0x0/0x60
[<c013e2c7>] do_generic_mapping_read+0x2e7/0x5f0
[<c013e79b>] __generic_file_aio_read+0xbb/0x250
[<c013e5d0>] file_read_actor+0x0/0x110
[<c014e8ff>] __handle_mm_fault+0x1bf/0x1d0
[<c013e98b>] generic_file_aio_read+0x5b/0x80
[<c015d49a>] do_sync_read+0xca/0x130
[<c0116999>] pgd_alloc+0x19/0x20
[<c0119768>] mm_init+0xd8/0x110
[<c01300e0>] autoremove_wake_function+0x0/0x60
[<c015d5d6>] vfs_read+0xd6/0x1b0
[<c0168a1e>] kernel_read+0x4e/0x60
[<c01693f9>] prepare_binprm+0xd9/0x100
[<c0169908>] do_execve+0x198/0x260
[<c0101cac>] sys_execve+0x3c/0x80
[<c01030c5>] syscall_call+0x7/0xb
handlers:
[<d0863350>] (ide_intr+0x0/0x180 [ide_core])
Disabling IRQ #15
hdc: ATAPI 24X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
lp0: using parport0 (interrupt-driven).
NET: Registered protocol family 10
Disabled Privacy Extensions on device c03148a0(lo)
IPv6 over IPv4 tunneling driver
apm: BIOS version 1.2 Flags 0x0f (Driver version 1.16ac)
apm: disabled on user request.
eth0: no IPv6 routers present
hdc: lost interrupt
irq 15: nobody cared (try booting with the "irqpoll" option)
[<c013cd0a>] __report_bad_irq+0x2a/0xa0
[<c013c69d>] handle_IRQ_event+0x3d/0x70
[<c013ce27>] note_interrupt+0x87/0xf0
[<c013c779>] __do_IRQ+0xa9/0xc0
[<d08ffa60>] cdrom_pc_intr+0x0/0x2a0 [ide_cd]
[<c01052f9>] do_IRQ+0x19/0x30
[<c0103b0a>] common_interrupt+0x1a/0x20
[<d08ffa60>] cdrom_pc_intr+0x0/0x2a0 [ide_cd]
[<d0863134>] ide_timer_expiry+0xc4/0x220 [ide_core]
[<d0863070>] ide_timer_expiry+0x0/0x220 [ide_core]
[<c0124ade>] run_timer_softirq+0xce/0x1b0
[<c0120872>] __do_softirq+0x42/0xa0
[<c01208f6>] do_softirq+0x26/0x30
[<c01052fe>] do_IRQ+0x1e/0x30
[<c0103b0a>] common_interrupt+0x1a/0x20
handlers:
[<d0863350>] (ide_intr+0x0/0x180 [ide_core])
Disabling IRQ #15
ide-cd: cmd 0x25 timed out
hdc: lost interrupt
ide-cd: cmd 0x25 timed out
hdc: lost interrupt
irq 15: nobody cared (try booting with the "irqpoll" option)
[<c013cd0a>] __report_bad_irq+0x2a/0xa0
[<c013c69d>] handle_IRQ_event+0x3d/0x70
[<c013ce27>] note_interrupt+0x87/0xf0
[<c013c779>] __do_IRQ+0xa9/0xc0
[<d08ffa60>] cdrom_pc_intr+0x0/0x2a0 [ide_cd]
[<c01052f9>] do_IRQ+0x19/0x30
[<c0103b0a>] common_interrupt+0x1a/0x20
[<d08ffa60>] cdrom_pc_intr+0x0/0x2a0 [ide_cd]
[<d0863134>] ide_timer_expiry+0xc4/0x220 [ide_core]
[<d0863070>] ide_timer_expiry+0x0/0x220 [ide_core]
[<c0124ade>] run_timer_softirq+0xce/0x1b0
[<c0120872>] __do_softirq+0x42/0xa0
[<c01208f6>] do_softirq+0x26/0x30
[<c01052fe>] do_IRQ+0x1e/0x30
[<c0103b0a>] common_interrupt+0x1a/0x20
[<c0101030>] default_idle+0x0/0x30
[<c0101056>] default_idle+0x26/0x30
[<c01010d3>] cpu_idle+0x33/0x50
[<c03468ba>] start_kernel+0x17a/0x1e0
[<c03463e0>] unknown_bootoption+0x0/0x1f0
handlers:
[<d0863350>] (ide_intr+0x0/0x180 [ide_core])
Disabling IRQ #15
Removed unneeded services from boot to speed things up a little.
Try with again "pci=routeirq"
No difference.
Try again with "pollirq"
Same behaviour although the precise call that gives a trace changes.
Reply to: