Bug#270102: kernel: modprobe aic79xx causes kobject_register failure
Package: kernel
Severity: normal
Second attempt to load module aic79xx causes the following:
# modprobe aic79xx
kobject_register failed for aic79xx (-17)
[<c01b32db>] kobject_register+0x5b/0x60
[<c02068e0>] bus_add_driver+0x50/0xc0
[<c01be1dc>] pci_register_driver+0x6c/0xa0
[<f8a766bf>] ahd_linux_pci_init+0xf/0x20 [aic79xx]
[<f8a6d725>] ahd_linux_detect+0x45/0x90 [aic79xx]
[<f882400f>] ahd_linux_init+0xf/0x24 [aic79xx]
[<c013a2f1>] sys_init_module+0x111/0x240
[<c01061f9>] sysenter_past_esp+0x52/0x71
hotplug package seems to try to load aic79xx multiple times
which causes a boot failure. (Should I raise a bug report for
hotplug too?). Removing hotplug package allows normal boot.
This problem does not occur with 2.6.6-2 but does with
2.6.7 and 2.6.8
Two boot logs are included, one a failure with hotplug
the second with boot param: init=/bin/bash and a manual
load of aic79xx.
-- System Information:
Debian Release: 3.1
APT prefers unstable
APT policy: (500, 'unstable')
Architecture: i386 (i686)
Kernel: Linux 2.6.8-1-k7-smp
Locale: LANG=C, LC_CTYPE=C
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009e800 (usable)
BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d2000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fef0000 (usable)
BIOS-e820: 000000003fef0000 - 000000003feff000 (ACPI data)
BIOS-e820: 000000003feff000 - 000000003ff00000 (ACPI NVS)
BIOS-e820: 000000003ff00000 - 000000003ff80000 (usable)
BIOS-e820: 000000003ff80000 - 0000000040000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec04000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Warning only 896MB will be used.
Use a HIGHMEM enabled kernel.
896MB LOWMEM available.
found SMP MP-table at 000f7170
DMI 2.3 present.
ACPI: RSDP (v000 PTLTD ) @ 0x000f7100
ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x3fefcf28
ACPI: FADT (v001 AMD TECATE 0x06040000 PTL 0x000f4240) @ 0x3fefef2e
ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x3fefefa2
ACPI: DSDT (v001 AMD AMDACPI 0x06040000 MSFT 0x0100000d) @ 0x00000000
ACPI: PM-Timer IO Port: 0x8008
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x01] enabled)
Processor #1 6:8 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:8 APIC version 16
WARNING: NR_CPUS limit of 1 reached. Processor ignored.
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: Assigned apic_id 2
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: root=/dev/sda2 ro console=ttyS0,115200
Initializing CPU#0
PID hash table entries: 4096 (order 12: 32768 bytes)
Detected 2000.282 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 901824k/917504k available (1329k kernel code, 14904k reserved, 727k data, 204k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3956.73 BogoMIPS
Security Scaffold v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: AMD Athlon(tm) MP 2400+ stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
masked ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
...TIMER: vector=0x31 pin1=2 pin2=-1
Using local APIC timer interrupts.
calibrating APIC timer ...
...... CPU clock speed is 1999.0790 MHz.
...... host bus clock speed is 266.0638 MHz.
checking if image is initramfs...it isn't (ungzip failed); looks like an initrd
Freeing initrd memory: 4328k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfd7d0, last bus=3
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 *5 10 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 5 10 11) *9
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 5 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 5 *10 11)
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f7130
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x9aad, dseg 0x400
PnPBIOS: 17 nodes reported by PnP BIOS; 17 recorded by driver
PCI: Using ACPI for IRQ routing
ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 20 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 21 (level, low) -> IRQ 177
ACPI: PCI interrupt 0000:01:05.0[A] -> GSI 18 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:03:00.0[D] -> GSI 19 (level, low) -> IRQ 193
ACPI: PCI interrupt 0000:03:04.0[A] -> GSI 16 (level, low) -> IRQ 201
ACPI: PCI interrupt 0000:03:04.1[B] -> GSI 17 (level, low) -> IRQ 209
ACPI: PCI interrupt 0000:03:05.0[A] -> GSI 17 (level, low) -> IRQ 209
ACPI: PCI interrupt 0000:03:06.0[A] -> GSI 18 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:03:06.1[B] -> GSI 19 (level, low) -> IRQ 193
ACPI: PCI interrupt 0000:03:06.2[C] -> GSI 16 (level, low) -> IRQ 201
ACPI: PCI interrupt 0000:03:07.0[A] -> GSI 19 (level, low) -> IRQ 193
testing the IO APIC.......................
Using vector-based indexing
..................................... done.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
BIOS failed to enable PCI standards compliance, fixing this error.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
EISA: Probing bus 0 at eisa0
Cannot allocate resource for EISA slot 1
Cannot allocate resource for EISA slot 2
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S1 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4328 blocks [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 204k freed
initrd-tools: 0.1.73
SCSI subsystem initialized
ACPI: PCI interrupt 0000:03:04.0[A] -> GSI 16 (level, low) -> IRQ 201
ACPI: PCI interrupt 0000:03:04.1[B] -> GSI 17 (level, low) -> IRQ 209
ACPI: PCI interrupt 0000:03:05.0[A] -> GSI 17 (level, low) -> IRQ 209
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 3960D Ultra160 SCSI adapter>
aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
Using anticipatory io scheduler
(scsi0:A:1): 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
Vendor: FUJITSU Model: MAN3367MP Rev: 0107
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:1:0: Tagged Queuing enabled. Depth 8
scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 3960D Ultra160 SCSI adapter>
aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs
scsi2 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 2940 Ultra SCSI adapter>
aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs
(scsi2:A:4): 20.000MB/s transfers (20.000MHz, offset 8)
Vendor: GENERIC Model: CRD-BP2 Rev: 2.21
Type: CD-ROM ANSI SCSI revision: 02
(scsi2:A:5): 10.000MB/s transfers (10.000MHz, offset 15)
Vendor: MATSHITA Model: DVD-RAM LF-D200 Rev: X120
Type: CD-ROM ANSI SCSI revision: 04
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
Attached scsi generic sg0 at scsi0, channel 0, id 1, lun 0, type 0
Attached scsi generic sg1 at scsi2, channel 0, id 4, lun 0, type 5
Attached scsi generic sg2 at scsi2, channel 0, id 5, lun 0, type 5
SCSI device sda: 71771688 512-byte hdwr sectors (36747 MB)
SCSI device sda: drive cache: write back
/dev/scsi/host0/bus0/target1/lun0: p1 p2 p3 < p5 p6 p7 p8 >
Attached scsi disk sda at scsi0, channel 0, id 1, lun 0
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
INIT: version 2.86 booting
Setting disc parameters: done.
Activating swap.
Adding 1172704k swap on /dev/sda5. Priority:-1 extents:1
Checking root file system...
fsck 1.35 (28-Feb-2004)
/dev/sda2: clean, 23565/124928 files, 446905/498EXT3 FS on sda2, internal journal
012 blocks
/etc/init.d/rcS: System clock was not updated at this time.
Cleaning up ifupdown...done.
WARNING: Bastille-firewall is not configured yet
Please create /etc/Bastille/bastille-firewall.cfg to enable it.
(HINT: use InteractiveBastille)
Calculating module dependencies... done.
Loading modules...
e1000
e1000: Ignoring new-style parameters in presence of obsolete ones
Intel(R) PRO/1000 Network Driver - version 5.2.52-k4
Copyright (c) 1999-2004 Intel Corporation.
ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 20 (level, low) -> IRQ 169
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
All modules loaded.
Capability LSM initialized
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com
Creating device-mapper devices...done.
Checking all file systems...
fsck 1.35 (28-Feb-2004)
/dev/sda6: recovering journal
/dev/sda6: clean, 177587/750720 files, 931761/1500061 blocks
/dev/sda7: recovering journal
/dev/sda7: clean, 22270/377856 files, 162431/755047 blocks (check in 2 mounts)
Setting kernel variables ...
.... done.
Mounting local filesystems...
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald st/dev/sda6 on /usr type ext3 (rw)
/dev/sda7 on /var type ext3 (rw)
arting. Commit interval 5 seconds
EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Setting sensors limits:Can't access procfs/sysfs file
Unable to find i2c bus information;
For 2.6 kernels, make sure you have mounted sysfs and done
'modprobe i2c_sensor'!
For older kernels, make sure you have done 'modprobe i2c-proc'!
Can't access procfs/sysfs file
Unable to find i2c bus information;
For 2.6 kernels, make sure you have mounted sysfs and done
'modprobe i2c_sensor'!
For older kernels, make sure you have done 'modprobe i2c-proc'!
done.
Running 0dns-down to make sure resolv.conf is ok...done.
/dev/shm/network/...Initializing: /etc/network/ifstate.
Starting hotplug subsystem:
input
evbug: blacklisted
evdev: loaded successfully
evbug: blacklisted
evdev: already loaded
input [success]
isapnp
Real Time Clock Driver v1.12
rtc: loaded sucessfully
input: PC Speaker
pcspkr: loaded sucessfully
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
mice: PS/2 mouse device common for all mice
psmouse: loaded sucessfully
ts: Compaq touchscreen protocol output
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
parport_pc: loaded sucessfully
inserting floppy driver for 2.6.8-1-386
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
floppy: loaded sucessfully
isapnp [success]
net
net [success]
pci
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected AMD 760MP chipset
agpgart: Maximum main memory to use for agp memory: 816M
agpgart: AGP aperture is 64M @ 0xf0000000
amd-k7-agp: loaded successfully
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5
modprobe: FATAL: Error inserting pciehp (/lib/modules/2.6.8-1-386/kernel/drivers/pci/hotplug/pciehp.ko): Operation not permitted
pciehp: can't be loaded
missing kernel or user mode driver pciehp
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
modprobe: FATAL: Error inserting shpchp (/lib/modules/2.6.8-1-386/kernel/drivers/pci/hotplug/shpchp.ko): Operation not permitted
shpchp: can't be loaded
missing kernel or user mode driver shpchp
amd76xrom amd76xrom_init_one(): Unable to register resource 0xffb00000-0xffffffff - kernel bug?
amd76xrom window : 500000 at ffb00000
CFI: Found no amd76xrom device at location zero
JEDEC: Found no amd76xrom device at location zero
CFI: Found no amd76xrom device at location zero
JEDEC: Found no amd76xrom device at location zero
CFI: Found no amd76xrom device at location zero
JEDEC: Found no amd76xrom device at location zero
CFI: Found no amd76xrom device at location zero
JEDEC: Found no amd76xrom device at location zero
CFI: Found no amd76xrom device at location zero
Found: PMC Pm49FL004
amd76xrom: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
amd76xrom chip at offset: 0x480000
amd76xrom: cannot reserve MTD resource
amd76xrom: loaded successfully
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
amd74xx: loaded successfully
hw_random: AMD768 system management I/O registers at 0x8000.
hw_random hardware driver 1.0.0 loaded
hw_random: loaded successfully
e1000: already loaded
Loading Adaptec I2O RAID: Version 2.4 Build 5go
Detecting Adaptec I2O RAID controllers...
ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 21 (level, low) -> IRQ 177
Adaptec I2O RAID controller 0 at f8ffa000 size=100000 irq=177
dpti: If you have a lot of devices this could take a few minutes.
dpti0: Reading the hardware resource table.
TID 008 Vendor: ADAPTEC Device: AIC-7899 Rev: 00000001
scsi3 : Vendor: Adaptec Model: 2110S FW:380E
dpt_i2o: loaded successfully
pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5
modprobe: FATAL: Error inserting pciehp (/lib/modules/2.6.8-1-386/kernel/drivers/pci/hotplug/pciehp.ko): Operation not permitted
pciehp: can't be loaded
missing kernel or user mode driver pciehp
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
modprobe: FATAL: Error inserting shpchp (/lib/modules/2.6.8-1-386/kernel/drivers/pci/hotplug/shpchp.ko): Operation not permitted
shpchp: can't be loaded
missing kernel or user mode driver shpchp
pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5
modprobe: FATAL: Error inserting pciehp (/lib/modules/2.6.8-1-386/kernel/drivers/pci/hotplug/pciehp.ko): Operation not permitted
pciehp: can't be loaded
missing kernel or user mode driver pciehp
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
modprobe: FATAL: Error inserting shpchp (/lib/modules/2.6.8-1-386/kernel/drivers/pci/hotplug/shpchp.ko): Operation not permitted
shpchp: can't be loaded
missing kernel or user mode driver shpchp
ignoring pci display device on 01:05.0
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ACPI: PCI interrupt 0000:03:00.0[D] -> GSI 19 (level, low) -> IRQ 193
ohci_hcd 0000:03:00.0: Advanced Micro Devices [AMD] AMD-768 [Opus] USB
ohci_hcd 0000:03:00.0: irq 193, pci mem f8977000
ohci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ACPI: PCI interrupt 0000:03:06.0[A] -> GSI 18 (level, low) -> IRQ 185
ohci_hcd 0000:03:06.0: NEC Corporation USB
ohci_hcd 0000:03:06.0: irq 185, pci mem f8fa9000
ohci_hcd 0000:03:06.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ACPI: PCI interrupt 0000:03:06.1[B] -> GSI 19 (level, low) -> IRQ 193
ohci_hcd 0000:03:06.1: NEC Corporation USB (#2)
ohci_hcd 0000:03:06.1: irq 193, pci mem f8fab000
ohci_hcd 0000:03:06.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci-hcd: loaded successfully
modprobe: FATAL: Error inserting aic79xx (/lib/modules/2.6.8-1-386/kernel/drivers/scsi/aic7xxx/aic79xx.ko): No such device
aic79xx: can't be loaded
missing kernel or user mode driver aic79xx
aic7xxx: already loaded
kobject_register failed for aic79xx (-17)
[<c018b8d3>] kobject_register+0x35/0x3d
[<c01d2f68>] bus_add_driver+0x38/0x70
[<c01d32d7>] driver_register+0x2d/0x31
[<c0193a7a>] pci_register_driver+0x4e/0x6b
[<f91a74e5>] ahd_linux_pci_init+0xa/0x12 [aic79xx]
[<f91a07ed>] ahd_linux_detect+0x3c/0x6c [aic79xx]
[<f897500a>] ahd_linux_init+0xa/0x19 [aic79xx]
[<c012af8c>] sys_init_module+0xe3/0x1d4
[<c0105f45>] sysenter_past_esp+0x52/0x71
modprobe: FATAL: Error inserting aic79xx (/lib/modules/2.6.8-1-386/kernel/drivers/scsi/aic7xxx/aic79xx.ko): No such device
aic79xx: can't be loaded
missing kernel or user mode driver aic79xx
aic7xxx: already loaded
aic7xxx: already loaded
ohci-hcd: already loaded
ohci-hcd: already loaded
Unable to handle kernel paging request at virtual address f91c2ab8
printing eip:
c018b855
*pde = 370cf067
*pte = 00000000
Oops: 0002 [#1]
PREEMPT
Modules linked in: ehci_hcd ohci_hcd usbcore dpt_i2o hw_random amd74xx ide_core cfi_cmdset_0002 cfi_util mtdpart jedec_probe cfi_probe gen_probe amd76xrom mtdcore chipreg map_funcs pci_hotplug amd_k7_agp agpgart floppy parport_pc tsdev parport mousedev psmouse pcspkr rtc evdev dm_mod capability commoncap e1000 xfs ext3 jbd sd_mod sg unix font vesafb cfbcopyarea cfbimgblt cfbfillrect aic7xxx scsi_mod
CPU: 0
EIP: 0060:[<c018b855>] Not tainted
EFLAGS: 00010296 (2.6.8-1-386)
EIP is at kobject_add+0x67/0xb0
eax: c02c19c0 ebx: f9101a3c ecx: f91c2ab8 edx: f9101a58
esi: c02c19c8 edi: f9101a24 ebp: 00000000 esp: f6a0ff40
ds: 007b es: 007b ss: 0068
Process modprobe (pid: 1815, threadinfo=f6a0e000 task=f6ce20f0)
Stack: f9101a3c ffffffea f9101a24 c018b8b9 f9101a3c f9101a3c f9101a3c c02c1960
c01d2f68 f9101a3c f9101a00 00000000 f9101a98 c0289e00 c01d32d7 f9101a24
f8fd6b4a f8fd1000 00000000 c0279124 c0193a7a f9101a24 c0289e18 f9101b00
Call Trace:
[<c018b8b9>] kobject_register+0x1b/0x3d
[<c01d2f68>] bus_add_driver+0x38/0x70
[<c01d32d7>] driver_register+0x2d/0x31
[<c0193a7a>] pci_register_driver+0x4e/0x6b
[<f8975018>] init+0x18/0x24 [ehci_hcd]
[<c012af8c>] sys_init_module+0xe3/0x1d4
[<c0105f45>] sysenter_past_esp+0x52/0x71
Code: 89 11 89 4a 04 8b 43 28 8b 00 83 c0 48 e8 35 14 00 00 89 73
./hotplug.functions: line 140: 1815 Segmentation fault $MODPROBE $MODULE >/dev/null 2>&1
ehci-hcd: can't be loaded
missing kernel or user mode driver ehci-hcd
emu10k1: blacklisted
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d2000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fef0000 (usable)
BIOS-e820: 000000003fef0000 - 000000003feff000 (ACPI data)
BIOS-e820: 000000003feff000 - 000000003ff00000 (ACPI NVS)
BIOS-e820: 000000003ff00000 - 000000003ff80000 (usable)
BIOS-e820: 000000003ff80000 - 0000000040000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec04000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f7170
DMI 2.3 present.
ACPI: RSDP (v000 PTLTD ) @ 0x000f7100
ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x3fefcf28
ACPI: FADT (v001 AMD TECATE 0x06040000 PTL 0x000f4240) @ 0x3fefef2e
ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x3fefefa2
ACPI: DSDT (v001 AMD AMDACPI 0x06040000 MSFT 0x0100000d) @ 0x00000000
ACPI: PM-Timer IO Port: 0x8008
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x01] enabled)
Processor #1 6:8 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:8 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: Assigned apic_id 2
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: root=/dev/sda2 ro console=ttyS0,115200 init=/bin/bash
Initializing CPU#0
PID hash table entries: 4096 (order 12: 32768 bytes)
Detected 2000.474 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1030132k/1048064k available (1636k kernel code, 16956k reserved, 775k data, 168k init, 130496k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3956.73 BogoMIPS
Security Scaffold v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: AMD Athlon(tm) MP 2400+ stepping 01
per-CPU timeslice cutoff: 731.38 usecs.
task migration cache decay timeout: 1 msecs.
masked ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Booting processor 1/0 eip 3000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 3997.69 BogoMIPS
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: AMD Athlon(tm) Processor stepping 01
Total of 2 processors activated (7954.43 BogoMIPS).
ENABLING IO-APIC IRQs
...TIMER: vector=0x31 pin1=2 pin2=-1
Using local APIC timer interrupts.
calibrating APIC timer ...
...... CPU clock speed is 1999.0725 MHz.
...... host bus clock speed is 266.0630 MHz.
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
checking if image is initramfs...it isn't (ungzip failed); looks like an initrd
Freeing initrd memory: 4724k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd7d0, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
mtrr: your CPUs had inconsistent fixed MTRR settings
mtrr: probably your BIOS does not setup all CPUs.
mtrr: corrected configuration.
ACPI: Subsystem revision 20040326
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 *5 10 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 5 10 11) *9
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 5 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 5 *10 11)
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f7130
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x9aad, dseg 0x400
PnPBIOS: 17 nodes reported by PnP BIOS; 17 recorded by driver
PCI: Using ACPI for IRQ routing
ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 20 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:01:05.0[A] -> GSI 18 (level, low) -> IRQ 177
ACPI: PCI interrupt 0000:02:00.0[D] -> GSI 19 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:02:04.0[A] -> GSI 16 (level, low) -> IRQ 193
ACPI: PCI interrupt 0000:02:04.1[B] -> GSI 17 (level, low) -> IRQ 201
ACPI: PCI interrupt 0000:02:06.0[A] -> GSI 18 (level, low) -> IRQ 177
ACPI: PCI interrupt 0000:02:06.1[B] -> GSI 19 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:02:06.2[C] -> GSI 16 (level, low) -> IRQ 193
ACPI: PCI interrupt 0000:02:07.0[A] -> GSI 19 (level, low) -> IRQ 185
testing the IO APIC.......................
Using vector-based indexing
..................................... done.
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
BIOS failed to enable PCI standards compliance, fixing this error.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S1 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4724 blocks [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 168k freed
initrd-tools: 0.1.74
SCSI subsystem initialized
ACPI: PCI interrupt 0000:02:04.0[A] -> GSI 16 (level, low) -> IRQ 193
ACPI: PCI interrupt 0000:02:04.1[B] -> GSI 17 (level, low) -> IRQ 201
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 3960D Ultra160 SCSI adapter>
aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
Using anticipatory io scheduler
(scsi0:A:1): 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
Vendor: FUJITSU Model: MAN3367MP Rev: 0107
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:1:0: Tagged Queuing enabled. Depth 8
scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 3960D Ultra160 SCSI adapter>
aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
Attached scsi generic sg0 at scsi0, channel 0, id 1, lun 0, type 0
SCSI device sda: 71771688 512-byte hdwr sectors (36747 MB)
SCSI device sda: drive cache: write back
/dev/scsi/host0/bus0/target1/lun0: p1 p2 p3 < p5 p6 p7 p8 >
Attached scsi disk sda at scsi0, channel 0, id 1, lun 0
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
root@(none):/# modprobe aic79xx
FATAL: Error inserting aic79xx (/lib/modules/2.6.8-1-k7-smp/kernel/drivers/scsi/aic7xxx/aic79xx.ko): No such device
root@(none):/# mount /proc
root@(none):/# lsmod
Module Size Used by
xfs 621596 0
ext3 129448 1
jbd 69976 1 ext3
mbcache 10500 1 ext3
sd_mod 22272 2
sg 40224 0
unix 31316 0
font 8896 0
vesafb 7136 0
cfbcopyarea 4224 1 vesafb
cfbimgblt 3520 1 vesafb
cfbfillrect 4160 1 vesafb
aic7xxx 207256 1
scsi_mod 127556 3 sd_mod,sg,aic7xxx
root@(none):/# modprobe aic79xx
kobject_register failed for aic79xx (-17)
[<c01b32db>] kobject_register+0x5b/0x60
[<c02068e0>] bus_add_driver+0x50/0xc0
[<c01be1dc>] pci_register_driver+0x6c/0xa0
[<f8a766bf>] ahd_linux_pci_init+0xf/0x20 [aic79xx]
[<f8a6d725>] ahd_linux_detect+0x45/0x90 [aic79xx]
[<f882400f>] ahd_linux_init+0xf/0x24 [aic79xx]
[<c013a2f1>] sys_init_module+0x111/0x240
[<c01061f9>] sysenter_past_esp+0x52/0x71
FATAL: Error inserting aic79xx (/lib/modules/2.6.8-1-k7-smp/kernel/drivers/scsi/aic7xxx/aic79xx.ko): No such device
root@(none):/# lsmod
Module Size Used by
xfs 621596 0
ext3 129448 1
jbd 69976 1 ext3
mbcache 10500 1 ext3
sd_mod 22272 2
sg 40224 0
unix 31316 0
font 8896 0
vesafb 7136 0
cfbcopyarea 4224 1 vesafb
cfbimgblt 3520 1 vesafb
cfbfillrect 4160 1 vesafb
aic7xxx 207256 1
scsi_mod 127556 3 sd_mod,sg,aic7xxx
root@(none):/#
Reply to: