Bug#260150: /usr/sbin/mkinitrd: Cannot determine SCSI module
Am Dienstag, 27. Juli 2004 16:05 schrieben Sie:
> * Christian Leimer <christian_leimer@web.de> [2004-07-18 23:23]:
> > I use sarge and tried to install the kernel-image-2.6.7-powerpc.
> > I got this error: /usr/sbin/mkinitrd: Cannot determine SCSI module
> > Failed to create initrd image.
> >
> > I have an Umax S900 with an Adaptec SCSI card as boot device.
>
> Was /proc mounted at that point? What does /proc/partitions contain?
> Can you send the output of dmesg?
mount:
/dev/sdb2 on / type unknown (rw,errors=remount-ro)
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
devpts on /dev/pts type devpts (rw,gid=5,mode=620)
tmpfs on /dev/shm type tmpfs (rw)
usbfs on /proc/bus/usb type usbfs (rw)
proc/partitions:
ajor minor #blocks name
8 0 8925132 sda
8 1 31 sda1
8 2 8523438 sda2
8 3 401662 sda3
8 16 4199328 sdb
8 17 31 sdb1
8 18 27 sdb2
8 19 37 sdb3
8 20 256 sdb4
8 21 4025590 sdb5
8 22 153600 sdb6
8 23 19785 sdb7
dmesg:
Total memory = 464MB; using 1024kB for hash table (at c0300000)
Linux version 2.6.7 (root@debian) (gcc-Version 3.3.4 (Debian 1:3.3.4-3)) #1
SMP Tue Jul 27 06:27:46 CEST 2004
Found a Grand Central mac-io controller, rev: 2, mapped at 0xfdeb5000
PowerMac motherboard: Unknown PowerSurge
Cache coherency enabled for bandit/PSX
Found Bandit PCI host bridge at 0xf2000000. Firmware bus number: 0->1
nvram: OF partition at 0x1800
nvram: XP partition at 0x1300
nvram: NR partition at 0x1400
On node 0 totalpages: 118784
DMA zone: 118784 pages, LIFO batch:16
Normal zone: 0 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line:
System has 32 possible interrupts
PID hash table entries: 2048 (order 11: 16384 bytes)
GMT Delta read from XPRAM: 120 minutes, DST: on
via_calibrate_decr: ticks per jiffy = 12499 (749990 ticks)
Console: colour dummy device 80x25
Memory: 466752k available (1888k kernel code, 1008k data, 144k init, 0k
highmem)
Calibrating delay loop... 398.33 BogoMIPS
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU 1 done callin...
CPU 1 done setup...
CPU 1 done timebase take...
Processor 1 found.
Brought up 2 CPUs
CPU0: online
domain 0: span 3
groups: 1 2
CPU1: online
domain 0: span 3
groups: 2 1
NET: Registered protocol family 16
PCI: Probing PCI hardware
Registering pmac pic with sysfs...
SCSI subsystem initialized
PCI: Enabling device 0000:00:0d.0 (0002 -> 0003)
fb: 3Dfx Voodoo3 memory = 16384K
PCI: Via IRQ fixup for 0000:01:01.0, from 25 to 9
PCI: Via IRQ fixup for 0000:01:01.1, from 25 to 9
Console: switching to colour frame buffer device 80x30
Generic RTC Driver v1.07
Macintosh non-volatile memory driver v1.1
MacIO PCI driver attached to Grand Central chipset
eth0: MACE at 00:05:9a:c0:ee:79, chip revision 9.64
Macintosh CUDA driver v0.5 for Unified ADB.
PCI: Enabling device 0000:00:0e.0 (0016 -> 0017)
adb: starting probe task...
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 2940 Ultra SCSI adapter>
aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs
Using anticipatory io scheduler
adb devices: [2]: 2 5 [3]: 3 1
ADB keyboard at 2, handler 1
Detected ADB keyboard, type ISO, swapping keys.
input: ADB keyboard on adb2:2.05/input
ADB mouse at 3, handler set to 2
input: ADB mouse on adb3:3.01/input
adb: finished probe task...
(scsi0:A:1): 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
Vendor: FUJITSU Model: MAH3091MP Rev: 5206
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:1:0: Tagged Queuing enabled. Depth 32
SCSI device sda: 17850264 512-byte hdwr sectors (9139 MB)
SCSI device sda: drive cache: write back
sda: [mac] sda1 sda2 sda3
Attached scsi disk sda at scsi0, channel 0, id 1, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 1, lun 0, type 0
mice: PS/2 mouse device common for all mice
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET: Registered protocol family 1
NET: Registered protocol family 17
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 144k init 4k chrp 8k prep
EXT3 FS on sda2, internal journal
mesh: configured for synchronous 10 MB/s
mesh: performing initial bus reset...
scsi1 : MESH
mesh: target 1 synchronous at 10.0 MB/s
Vendor: MATSHITA Model: CD-ROM CR-508 Rev: XS03
Type: CD-ROM ANSI SCSI revision: 02
sr0: scsi-1 drive
Uniform CD-ROM driver Revision: 3.20
Attached scsi CD-ROM sr0 at scsi1, channel 0, id 1, lun 0
Attached scsi generic sg1 at scsi1, channel 0, id 1, lun 0, type 5
mesh: target 2 synchronous at 10.0 MB/s
Vendor: MICROP Model: 4743NS Rev: S168
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sdb: 8398656 512-byte hdwr sectors (4300 MB)
SCSI device sdb: drive cache: write back
sdb: [mac] sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb7
Attached scsi disk sdb at scsi1, channel 0, id 2, lun 0
Attached scsi generic sg2 at scsi1, channel 0, id 2, lun 0, type 0
usbcore: registered new driver usbfs
usbcore: registered new driver hub
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
USB Universal Host Controller Interface driver v2.2
PCI: Enabling device 0000:01:01.0 (0014 -> 0015)
uhci_hcd 0000:01:01.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller
uhci_hcd 0000:01:01.0: irq 25, io base 00001020
uhci_hcd 0000:01:01.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
PCI: Enabling device 0000:01:01.1 (0014 -> 0015)
uhci_hcd 0000:01:01.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (#2)
uhci_hcd 0000:01:01.1: irq 25, io base 00001000
uhci_hcd 0000:01:01.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 1-1: new low speed USB device using address 2
Unable to find swap-space signature
drivers/usb/input/hid-core.c: ctrl urb status -2 received
drivers/usb/input/hid-core.c: timeout initializing reports
input: USB HID v1.10 Mouse [Acrox USB & PS/2 Mouse] on usb-0000:01:01.0-1
usb 1-2: new full speed USB device using address 3
NET: Registered protocol family 5
Reply to: