Re: Problema con Masterizzatore
On 02/05/2017 19:12, Davide Prina wrote:
On 01/05/2017 17:21, Portobello wrote:
Ma non scrive più, non masterizza né i DVD né i CD-ROM.
prova con wodim
Ho usato anche wodim.
Credo che ci sono errori anche hardware, ma non capisco quali sono.
Questi sono i messaggi che mi dà :
wodim -v -eject dev=/dev/sr1 speed=4 debian-testing-amd64-xfce-CD-1.iso
wodim: No write mode specified.
wodim: Assuming -tao mode.
wodim: Future versions of wodim may have different drive dependent defaults.
TOC Type: 1 = CD-ROM
scsidev: '/dev/sr1'
devname: '/dev/sr1'
scsibus: -2 target: -2 lun: -2
Linux sg driver version: 3.5.27
Wodim version: 1.1.11
SCSI buffer size: 64512
Device type : Removable CD-ROM
Version : 5
Response Format: 2
Capabilities :
Vendor_info : 'Optiarc '
Identification : 'DVD RW AD-7170S '
Revision : '1.00'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x000A (CD-RW)
Profile: 0x002B (DVD+R/DL)
Profile: 0x001B (DVD+R)
Profile: 0x001A (DVD+RW)
Profile: 0x0016 (DVD-R/DL layer jump recording)
Profile: 0x0015 (DVD-R/DL sequential recording)
Profile: 0x0014 (DVD-RW sequential recording)
Profile: 0x0013 (DVD-RW restricted overwrite)
Profile: 0x0012 (DVD-RAM)
Profile: 0x0011 (DVD-R sequential recording)
Profile: 0x0010 (DVD-ROM)
Profile: 0x000A (CD-RW) (current)
Profile: 0x0009 (CD-R)
Profile: 0x0008 (CD-ROM) (current)
Profile: 0x0002 (Removable disk)
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96R RAW/R96R
Drive buf size : 890880 = 870 KB
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
FIFO size : 12582912 = 12288 KB
Track 01: data 632 MB
Total size: 725 MB (71:54.48) = 323586 sectors
Lout start: 726 MB (71:56/36) = 323586 sectors
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 3
Reference speed: 6
Is not unrestricted
Is erasable
Disk sub type: High speed Rewritable (CAV) media (1)
ATIP start of lead in: -11745 (97:25/30)
ATIP start of lead out: 359848 (79:59/73)
1T speed low: 4 1T speed high: 10
2T speed low: 4 2T speed high: 0 (reserved val 6)
power mult factor: 1 5
recommended erase/write power: 5
A1 values: 24 1A D8
A2 values: 26 B2 4A
Disk type: Phase change
Manuf. index: 40
Manufacturer: INFODISC Technology Co., Ltd.
Blocks total: 359848 Blocks current: 359848 Blocks remaining: 36262
Speed set to 1764 KB/s
Starting to write CD/DVD at speed 10.0 in real TAO mode for single session.
Last chance to quit, starting real write in 0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
Performing OPC...
Starting new track at sector: 0
Track 01: 47 of 632 MB written (fifo 100%) [buf 100%] 10.2x.Errno: 5
(Input/output error), write_g1 scsi sendcmd: no error
CDB: 2A 00 00 00 5E 36 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 04 00 00 00 00 0A 00 00 00 00 08 03 00 00
Sense Key: 0x4 Hardware Error, Segment 0
Sense Code: 0x08 Qual 0x03 (logical unit communication crc error
(ultra-dma/32)) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.049s timeout 40s
write track data: error after 49393664 bytes
wodim: A write error occured.
wodim: Please properly read the error message above.
Writing time: 48.934s
Average write speed 111.4x.
Min drive buffer fill was 100%
Fixating...
Fixating time: 33.161s
BURN-Free was 1 times used.
wodim: fifo had 969 puts and 779 gets.
wodim: fifo was 0 times empty and 765 times full, min fill was 96%.
root@amd64:/home/nuovo/Documenti/varie_linux/debian/netinst_stretch#
Ciao
Grazie
Reply to: