Innanzitutto grazie per le vostre "corpose" e dettagliate risposte , sono molto legato a
cio' che studio ma manco di esperienza , ecco il perche' di tante mail (grazie anche della
pazienza) e di tante domande .
Per quanto riguarda gli ip , per la d-link andro' di statico e questo e' assodato , poi
siccome non avro' macchine che contattero' da internet dietro al wireless , ma solo dei
laptop per quanto riguarda bridge o subnet , configurero' il tutto con iptables , cosi'
permetto ai laptop di comunicare con i server in lan e viceversa .
Per il momento quando faccio ripartire il networking , wlano0 non viene su' e guardando
questo logs ho il sospetto che il driver acx non sia proprio quello giusto ma m-a non
sbaglia , quindi suppongo acx sia stato scritto in questi giorni per sostituire acx100 che,
nei miei precedenti tentativi ha si configurato le interfacce , una fatica per tirarle su',
acx molto meno , ma la macchina mi e' andata in kernel panik ... secca !!!
Per quanto riguarda scrivere l'howto , ne saro' felicissimo e ne saro' ancora piu' felice se
lo facessi dalle pagine del mio sito http://www.gabrix.ath.cx/ queste mail saranno molto
utili anche per quello e darei anche una mano a Craig .
Mi piacerebbe un vostro giudizio sul mio sito che naturalmente e' debian based !
Sep 25 08:34:18 ns1 kernel: acx: this driver is still EXPERIMENTAL
Sep 25 08:34:18 ns1 kernel: acx: this driver is still EXPERIMENTAL
Sep 25 08:34:18 ns1 kernel: acx: reading README file and/or Craig's HOWTO is recommended,
visit http://acx100.sf.net in case of further questions/discussion
Sep 25 08:34:18 ns1 kernel: acx: reading README file and/or Craig's HOWTO is recommended,
visit http://acx100.sf.net in case of further questions/discussion
Sep 25 08:34:18 ns1 kernel: acx: compiled to use 32bit I/O access. I/O timing issues might
occur, such as non-working firmware upload. Report them
Sep 25 08:34:18 ns1 kernel: acx: compiled to use 32bit I/O access. I/O timing issues might
occur, such as non-working firmware upload. Report them
Sep 25 08:34:18 ns1 kernel: running on a little-endian CPU
Sep 25 08:34:18 ns1 kernel: running on a little-endian CPU
Sep 25 08:34:18 ns1 kernel: PCI module v0.3.36 initialized, waiting for cards to probe...
Sep 25 08:34:18 ns1 kernel: PCI module v0.3.36 initialized, waiting for cards to probe...
Sep 25 08:34:18 ns1 kernel: PCI: Enabling device 0000:01:00.0 (0000 -> 0003)
Sep 25 08:34:18 ns1 kernel: PCI: Enabling device 0000:01:00.0 (0000 -> 0003)
Sep 25 08:34:18 ns1 kernel: PCI: Found IRQ 11 for device 0000:01:00.0
Sep 25 08:34:18 ns1 kernel: PCI: Sharing IRQ 11 with 0000:00:1f.2
Sep 25 08:34:18 ns1 kernel: acx: found ACX100-based wireless network card at 0000:01:00.0,
irq:11, phymem1:0xEC110000, phymem2:0xEC100000, mem1:0xd0d34000, mem1_size:4096,
mem2:0xd0d60000, mem2_size:65536
Sep 25 08:34:18 ns1 kernel: acx: found ACX100-based wireless network card at 0000:01:00.0,
irq:11, phymem1:0xEC110000, phymem2:0xEC100000, mem1:0xd0d34000, mem1_size:4096,
mem2:0xd0d60000, mem2_size:65536
Sep 25 08:34:18 ns1 kernel: using IRQ 11
Sep 25 08:34:18 ns1 kernel: using IRQ 11
Sep 25 08:34:18 ns1 kernel: acx: need to load firmware for acx100 chipset with radio ID 0d,
please provide via firmware hotplug:
Sep 25 08:34:18 ns1 kernel: acx: need to load firmware for acx100 chipset with radio ID 0d,
please provide via firmware hotplug:
Sep 25 08:34:18 ns1 kernel: acx: either one file only (<c>ombined firmware image file,
radio-specific) or two files (radio-less base image file *plus* separate <r>adio-specific
extension file)
Sep 25 08:34:18 ns1 kernel: acx: either one file only (<c>ombined firmware image file,
radio-specific) or two files (radio-less base image file *plus* separate <r>adio-specific
extension file)
Sep 25 08:34:18 ns1 kernel: requesting firmware image 'tiacx100c0D'
Sep 25 08:34:18 ns1 kernel: requesting firmware image 'tiacx100c0D'
Sep 25 08:34:18 ns1 kernel: acx: firmware image 'tiacx100c0D' was not provided. Check your
hotplug scripts
Sep 25 08:34:18 ns1 kernel: acx: firmware image 'tiacx100c0D' was not provided. Check your
hotplug scripts
Sep 25 08:34:18 ns1 kernel: requesting firmware image 'tiacx100'
Sep 25 08:34:18 ns1 kernel: requesting firmware image 'tiacx100'
Sep 25 08:34:18 ns1 kernel: acx_write_fw (main/combined): 0
Sep 25 08:34:18 ns1 kernel: acx_write_fw (main/combined): 0
Sep 25 08:34:18 ns1 kernel: acx_validate_fw (main/combined): 0
Sep 25 08:34:18 ns1 kernel: acx_validate_fw (main/combined): 0
Sep 25 08:34:18 ns1 kernel: requesting firmware image 'tiacx100r0D'
Sep 25 08:34:18 ns1 kernel: requesting firmware image 'tiacx100r0D'
Sep 25 08:34:18 ns1 kernel: acx_write_fw (radio): 0
Sep 25 08:34:18 ns1 kernel: acx_write_fw (radio): 0
Sep 25 08:34:18 ns1 kernel: acx_validate_fw (radio): 0
Sep 25 08:34:18 ns1 kernel: acx_validate_fw (radio): 0
Sep 25 08:34:18 ns1 kernel: acx100_s_init_wep: writing WEP options
Sep 25 08:34:18 ns1 kernel: acx100_s_init_wep: writing WEP options
Sep 25 08:34:18 ns1 kernel: initializing max packet templates
Sep 25 08:34:18 ns1 kernel: initializing max packet templates
Sep 25 08:34:19 ns1 kernel: NVS_vendor_offs:0000 probe_delay:500 eof_memory:65536
Sep 25 08:34:19 ns1 kernel: NVS_vendor_offs:0000 probe_delay:500 eof_memory:65536
Sep 25 08:34:19 ns1 kernel: CCAModes:04 Diversity:01 ShortPreOpt:01 PBCC:01 ChanAgil:00
PHY:05 Temp:01
Sep 25 08:34:19 ns1 kernel: CCAModes:04 Diversity:01 ShortPreOpt:01 PBCC:01 ChanAgil:00
PHY:05 Temp:01
Sep 25 08:34:19 ns1 kernel: AntennaID:00 Len:02 Data:01 02
Sep 25 08:34:19 ns1 kernel: AntennaID:00 Len:02 Data:01 02
Sep 25 08:34:19 ns1 kernel: PowerLevelID:01 Len:02 Data:001E 000A
Sep 25 08:34:19 ns1 kernel: PowerLevelID:01 Len:02 Data:001E 000A
Sep 25 08:34:19 ns1 kernel: DataRatesID:02 Len:05 Data:02 04 11 22 44
Sep 25 08:34:19 ns1 kernel: DataRatesID:02 Len:05 Data:02 04 11 22 44
Sep 25 08:34:19 ns1 kernel: DomainID:03 Len:06 Data:30 20 10 31 32 41
Sep 25 08:34:19 ns1 kernel: DomainID:03 Len:06 Data:30 20 10 31 32 41
Sep 25 08:34:19 ns1 kernel: ProductID:04 Len:09 Data:TI ACX100
Sep 25 08:34:19 ns1 kernel: ProductID:04 Len:09 Data:TI ACX100
Sep 25 08:34:19 ns1 kernel: ManufacturerID:05 Len:07 Data:TI Test
Sep 25 08:34:19 ns1 kernel: ManufacturerID:05 Len:07 Data:TI Test
Sep 25 08:34:19 ns1 kernel: get_mask 0x00004D82, set_mask 0x00000000
Sep 25 08:34:19 ns1 kernel: get_mask 0x00004D82, set_mask 0x00000000
Sep 25 08:34:19 ns1 kernel: got sensitivity value 176
Sep 25 08:34:19 ns1 kernel: got sensitivity value 176
Sep 25 08:34:19 ns1 kernel: got antenna value 0x8D
Sep 25 08:34:19 ns1 kernel: got antenna value 0x8D
Sep 25 08:34:19 ns1 kernel: got Energy Detect (ED) threshold 112
Sep 25 08:34:19 ns1 kernel: got Energy Detect (ED) threshold 112
Sep 25 08:34:19 ns1 kernel: got Channel Clear Assessment (CCA) value 13
Sep 25 08:34:19 ns1 kernel: got Channel Clear Assessment (CCA) value 13
Sep 25 08:34:19 ns1 kernel: got regulatory domain 0x30
Sep 25 08:34:19 ns1 kernel: got regulatory domain 0x30
Sep 25 08:34:19 ns1 kernel: get_mask 0x00000000, set_mask 0x00000000 - after update
Sep 25 08:34:19 ns1 kernel: get_mask 0x00000000, set_mask 0x00000000 - after update
Sep 25 08:34:19 ns1 kernel: new ratevector: 82 84 0B 16 2C
Sep 25 08:34:19 ns1 kernel: new ratevector: 82 84 0B 16 2C
Sep 25 08:34:19 ns1 kernel: setting RXconfig to 2010:0FDD
Sep 25 08:34:19 ns1 kernel: setting RXconfig to 2010:0FDD
Sep 25 08:34:19 ns1 kernel: acx: === chipset TNETW1100B, radio type 0x0D (Maxim), form
factor 0x01 ((mini-)PCI / CardBus), EEPROM version 0x05: uploaded firmware 'Rev 1.9.8.b' ===
Sep 25 08:34:19 ns1 kernel: acx: === chipset TNETW1100B, radio type 0x0D (Maxim), form
factor 0x01 ((mini-)PCI / CardBus), EEPROM version 0x05: uploaded firmware 'Rev 1.9.8.b' ===
Sep 25 08:34:19 ns1 kernel: creating /proc entry driver/acx_wlan0
Sep 25 08:34:19 ns1 kernel: creating /proc entry driver/acx_wlan0
Sep 25 08:34:19 ns1 kernel: creating /proc entry driver/acx_wlan0_diag
Sep 25 08:34:19 ns1 kernel: creating /proc entry driver/acx_wlan0_diag
Sep 25 08:34:19 ns1 kernel: creating /proc entry driver/acx_wlan0_eeprom
Sep 25 08:34:19 ns1 kernel: creating /proc entry driver/acx_wlan0_eeprom
Sep 25 08:34:19 ns1 kernel: creating /proc entry driver/acx_wlan0_phy
Sep 25 08:34:19 ns1 kernel: creating /proc entry driver/acx_wlan0_phy
Sep 25 08:34:19 ns1 kernel: acx v0.3.36: net device wlan0, driver compiled against wireless
extensions 20 and Linux 2.6.18-4-686
Sep 25 08:34:19 ns1 kernel: acx v0.3.36: net device wlan0, driver compiled against wireless
extensions 20 and Linux 2.6.18-4-686
Sep 25 08:34:19 ns1 kernel: USB module v0.3.36 initialized, probing for devices...
Sep 25 08:34:19 ns1 kernel: USB module v0.3.36 initialized, probing for devices...
Sep 25 08:34:19 ns1 kernel: usbcore: registered new driver acx_usb
Sep 25 08:41:05 ns1 kernel: new adev->mode=0
Sep 25 08:41:05 ns1 kernel: new adev->mode=0
Sep 25 08:41:17 ns1 kernel: acx: master mode (HostAP) is very, very experimental! It might
work partially, but better get prepared for nasty surprises at any time
Sep 25 08:41:17 ns1 kernel: acx: master mode (HostAP) is very, very experimental! It might
work partially, but better get prepared for nasty surprises at any time
Sep 25 08:41:17 ns1 kernel: new adev->mode=3
Sep 25 08:41:17 ns1 kernel: new adev->mode=3
Saluti!
--
Gabriele
http://www.gabrix.ath.cx/
mail: root@gabrix.ath.cx
msn: sickuser@gmail.com
sec 1024D/AD2077C5 2007-07-15
Key fingerprint = C3A7 AE50 C448 46FC 42E8 636E 45B2 12CF AD20 77C5
uid Gabriele (ULTIMA) <gabrix@gabrix.ath.cx>
ssb 4096g/81B02765 2007-07-15
Attachment:
signature.asc
Description: Digital signature