Re: R: Velocità HD
Su www.lecco.linux.it alla sezione software trovate fasthd...
----- Original Message -----
From: "Giacomo Tesio" <giacomo@tesio.it>
To: <debian-italian@lists.debian.org>
Sent: Saturday, August 31, 2002 12:58 PM
Subject: Re: R: Velocità HD
> Michele Bonera wrote:
>
> >Alle 12:12, giovedì 29 agosto 2002, Sethi ha scritto:
> >
> >
> >
> >>/dev/null Avevi ragione....
> >>cheope:/home/sethi# hdparm -t /dev/hda /dev/hdb /dev/hdd
> >>/dev/hda:
> >> Timing buffered disk reads: 64 MB in 2.48 seconds = 25.81 MB/sec
> >>
> >>
> >
> >Prova con
> >
> >hdparm -m128 -u1 -c3 -W1 -A1 -d1 -X69 /dev/hda
> >
> >(fammi sapere!)
> >
> >Byezz
> >
> Ehm... lo so che queste cose non si fanno, ma ho provato anch'io (e
> senza leggere la man)
>
> L'output è stato questo: non va male vero?
>
> localhost:/home/user# hdparm -i /dev/hda
>
> /dev/hda:
>
> Model=Maxtor 5T060H6, FwRev=TAH71DP0, SerialNo=T6HJRMPC
> Config={ Fixed }
> RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
> BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
> CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=120103200
> IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
> PIO modes: pio0 pio1 pio2 pio3 pio4
> DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
> AdvancedPM=yes: disabled (255) WriteCache=enabled
> Drive Supports : ATA/ATAPI-6 T13 1410D revision 0 : ATA-1 ATA-2 ATA-3
> ATA-4 ATA-5 ATA-6
>
> localhost:/home/user# hdparm -m16 -u1 -c3 -W1 -A1 -d1 -X69 /dev/hda
>
> /dev/hda:
> setting 32-bit I/O support flag to 3
> setting multcount to 16
> setting unmaskirq to 1 (on)
> setting using_dma to 1 (on)
> setting xfermode to 69 (UltraDMA mode5)
> setting drive read-lookahead to 1 (on)
> setting drive write-caching to 1 (on)
> multcount = 16 (on)
> I/O support = 3 (32-bit w/sync)
> unmaskirq = 1 (on)
> using_dma = 1 (on)
> localhost:/home/user# hdparm -t /dev/hda
>
> /dev/hda:
> Timing buffered disk reads: 64 MB in 1.76 seconds = 36.36 MB/sec
> localhost:/home/user# hdparm -T /dev/hda
>
> /dev/hda:
> Timing buffer-cache reads: 128 MB in 0.80 seconds =160.00 MB/sec
>
>
> Ciao e grazie
> Giacomo
> che se lo sgridate non si offende :-)
>
>
>
>
> --
> To UNSUBSCRIBE, email to debian-italian-request@lists.debian.org
> with a subject of "unsubscribe". Trouble? Contact
listmaster@lists.debian.org
>
Reply to: