Sarge install pb
Hello,
I'm trying to install sarge on a K220 server...
I have a kernel panic in the install when trying to load the 8250 driver
(see trace below)
Any idea ?
Firmware Version 2.2
Duplex Console IO Dependent Code (IODC) revision 4
------------------------------------------------------------------------------
(c) Copyright 1990-1998, Hewlett-Packard Company, All rights reserved
------------------------------------------------------------------------------
Processor Speed State CoProcessor State Cache Size
--------- -------- --------------------- ----------------- ----------
0 120 MHz Active Functional 1 M
1 120 MHz Idle Functional 1 M
Central Bus Speed (in MHz) : 120
Available Memory (bytes) : 536870912
Good Memory Required (bytes): 42819584
Primary boot path: 10/12/5.0 (dec)
Alternate boot path: 10/6.0 (dec)
Console path: 10/4/0.0 (dec)
Keyboard path: 10/12/7.0 (dec)
CPU 0
WARNING: Both STANDARD and EDO DRAMS are installed in this system.
WARNING: Memory has been initialized, but not tested as a result of
FASTBOOT being enabled. To test memory, use the FASTBOOT
command in the CONFIGURATION menu and reboot the system.
WARNING: Memory configuration is not optimized for performance. Refer
to the System Installation or Memory Installation manuals for
memory configuration guidelines.
Processor is booting from first available device.
To discontinue, press any key within 10 seconds.
Boot terminated.
------- Main Menu
-------------------------------------------------------------
Command Description
------- -----------
BOot [PRI|ALT|<path>] Boot from specified path
PAth [PRI|ALT] [<path>] Display or modify a path
SEArch [DIsplay|IPL] [<path>] Search for boot devices
COnfiguration menu Displays or sets boot values
INformation menu Displays hardware information
SERvice menu Displays service commands
DIsplay Redisplay the current menu
HElp [<menu>|<command>] Display help for menu or command
RESET Restart the system
-------
Main Menu: Enter command or menu > sea ipl
Searching for device(s) with bootable media
This may take several minutes.
To discontinue search, press any key (termination may not be immediate).
Path Number Device Path (dec) Device Type and Utilities
----------- ----------------- -------------------------
P0 10/0.5 Random access media
IPL
P1 10/12/5.2 Random access media
IPL
P2 10/12/6.0 LAN Module
Main Menu: Enter command or menu > boot p1
Interact with IPL (Y or N)?> Y
Booting...
Boot IO Dependent Code (IODC) revision 0
HARD Booted.
palo ipl 1.5 root@c3k Tue Sep 21 15:14:05 MDT 2004
Boot image contains:
0/vmlinux32 4319117 bytes @ 0x7a4800
0/vmlinux64 5820539 bytes @ 0x217000
0/ramdisk 2085296 bytes @ 0x10800
Information: No console specified on kernel command line. This is normal.
PALO will choose the console currently used by firmware (serial).Current
command line:
0/linux root=/dev/ram0 ramdisk_size=16384 initrd=0/ramdisk console=ttyB0
TERM=vt102
0: 0/linux
1: root=/dev/ram0
2: ramdisk_size=16384
3: initrd=0/ramdisk
4: console=ttyB0
5: TERM=vt102
<#> edit the numbered field
'b' boot with this command line
'r' restore command line
'l' list dir
? 0 4
console=ttyB0 S0
Current command line:
0/linux root=/dev/ram0 ramdisk_size=16384 initrd=0/ramdisk console=ttyS0
TERM=vt102
0: 0/linux
1: root=/dev/ram0
2: ramdisk_size=16384
3: initrd=0/ramdisk
4: console=ttyS0
5: TERM=vt102
<#> edit the numbered field
'b' boot with this command line
'r' restore command line
'l' list dir
? 0 b
Command line for kernel: 'root=/dev/ram0 ramdisk_size=16384
console=ttyS0 TERM=vt102 palo_kernel=0/linux'
Selected kernel: /linux from partition 0
Selected ramdisk: /ramdisk from partition 0
Warning: kernel name doesn't end with 32 or 64 -- Guessing... Choosing
32-bit kernelELF32 executable
Entry 00100000 first 00100000 n 2
Segment 0 load 00100000 size 2241844 mediaptr 0x1000
Segment 1 load 00324000 size 1056901 mediaptr 0x225000
Loading ramdisk 2085296 bytes @ 1fdf2000...
Branching to kernel entry point 0x00100000. If this is the last
message you see, you may need to switch your console. This is
a common symptom -- search the FAQ and mailing list at parisc-linux.org
Linux version 2.6.8-2-32 (kyle@caradhras) (gcc version 3.3.5 (Debian
1:3.3.5-7)) #1 Tue Feb 8 00:15:05 EST 2005
FP[0] enabled: Rev 1 Model 11
The 32-bit Kernel has started...
Determining PDC firmware type: System Map.
model 000058c0 00000491 00000000 00000002 19c88b80 100000f1 00000004
0000008a 0000008a
vers 0000000d
CPUID vers 11 rev 13 (0x0000016d)
model 9000/859/K220
Total Memory: 512 Mb
initrd: 2fdf2000-2ffef1b0
initrd: reserving 1fdf2000-1ffef1b0 (mem_max 20000000)
Built 1 zonelists
Kernel command line: root=/dev/ram0 ramdisk_size=16384 console=ttyS0
TERM=vt102 palo_kernel=0/linux
PID hash table entries: 16 (order 4: 128 bytes)
Console: colour dummy device 160x64
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 524288k available
Calibrating delay loop... 119.60 BogoMIPS
Security Scaffold v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
checking if image is initramfs...it isn't (no cpio magic); looks like an
initrd
NET: Registered protocol family 16
EISA bus registered
Searching for devices...
Found devices:
1. U2-IOA BC Runway Port at 0xfff88000 [8] { 12, 0x7, 0x580, 0x0000b }
2. U2-IOA BC GSC+ Port at 0xf103f000 [8/63] { 7, 0x1, 0x501, 0x0000c }
3. U2-IOA BC Runway Port at 0xfff8a000 [10] { 12, 0x7, 0x580, 0x0000b }
4. KittyHawk GSY Core FW-SCSI at 0xf1800000 [10/0] { 4, 0x1, 0x015,
0x00089 }
5. Gecko BOA BC GSC+ Port at 0xf1804000 [10/4] { 7, 0x0, 0x500, 0x0000c }
6. Eole CAP/MUX at 0xf1900000 [10/4/0] { 5, 0x0, 0x015, 0x0000d }
7. Wizard SCSI at 0xf1904000 [10/4/4] { 4, 0x0, 0x004, 0x0003b }
8. Wizard SCSI at 0xf190c000 [10/4/12] { 4, 0x0, 0x004, 0x0003b }
9. Gecko BOA BC HP-PB Port at 0xf193c000 [10/4/60] { 7, 0x0, 0x103,
0x0000c }
10. Baby Hugo Add-on mass FC (A3404A) at 0xf1808000 [10/8] { 4, 0x0,
0x015, 0x000a7 }
11. KittyHawk GSY Core BA at 0xffd00000 [10/12] { 11, 0x0, 0x015,
0x00081 }, additional addresses: 0xffd0c000 0xffc00000
12. KittyHawk GSY Core Centronics at 0xffd02000 [10/12/0] { 10, 0x0,
0x015, 0x00074 }, additional addresses: 0xffd01000 0xffd03000
13. KittyHawk GSY Core SCSI at 0xffd06000 [10/12/5] { 10, 0x0, 0x015,
0x00082 }
14. KittyHawk GSY Core LAN (802.3) at 0xffd07000 [10/12/6] { 10, 0x0,
0x015, 0x0008a }
15. KittyHawk GSY Core PS/2 Port at 0xffd08000 [10/12/7] { 10, 0x0,
0x015, 0x00084 }
16. KittyHawk GSY Core PS/2 Port at 0xffd08100 [10/12/8] { 10, 0x0,
0x015, 0x00084 }
17. U2-IOA BC GSC+ Port at 0xf183f000 [10/63] { 7, 0x1, 0x501, 0x0000c }
18. ThunderHawk DC3- 120 1M (K220) at 0xfffa0000 [32] { 0, 0x0, 0x58c,
0x00004 }
19. ThunderHawk DC3- 120 1M (K220) at 0xfffa2000 [34] { 0, 0x0, 0x58c,
0x00004 }
20. Memory at 0xfffb1000 [49] { 1, 0x0, 0x053, 0x00009 }
CONFIG_SMP=n ignoring additional CPUs
CPU: probe of parisc34 failed with error 1
CPU(s): 1 x PA7200 (PCX-T') at 120.000000 MHz
Found U2 at 0xfff88000
Found U2 at 0xfff8a000
Lasi version 0 at 0xffd00000 found.
LED display at ffd0c000 registered
Found GeckoBoa at 0xf1804000
SCSI subsystem initialized
TC classifier action (bugs to netdev@oss.sgi.com cc hadi@cyberus.ca)
STI GSC/PCI core graphics driver Version 0.9a
unwind_init: start = 0x10325720, end = 0x103468a0, entries = 8472
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
Soft power switch support not available.
Generic RTC Driver v1.07
Serial: 8250/16550 driver $Revision: 1.90 $ 25 ports, IRQ sharing enabled
Backtrace:
[<1022bb68>] serial8250_get_divisor+0x44/0x50
[<1022bc18>] serial8250_set_termios+0xa4/0x364
[<103e7384>] uart_set_options+0xec/0x14c
[<103e75fc>] serial8250_console_setup+0xbc/0xd0
[<1012aa4c>] register_console+0x1b0/0x214
[<103e7654>] serial8250_console_init+0x44/0x4c
[<103e78c8>] serial8250_pci_init+0x20/0x38
[<103d9348>] do_initcalls+0x58/0xf8
[<10102fb8>] init+0x38/0x108
[<1010ec5c>] ret_from_kernel_thread+0x1c/0x24
Kernel Fault: Code=13 regs=2fda03c0 (Addr=00000000)
YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI
PSW: 00000000000001001111111100001111 Not tainted
r00-03 00000000 ffffffff 1022bb68 1044c9a0
r04-07 00000000 2fda0288 00000013 10360010
r08-11 1035f000 00000000 4df21500 10431a40
r12-15 1035f1b0 3b9aca00 10361810 10431810
r16-19 f0001570 f0000074 f000006c 00009600
r20-23 00000000 01000000 00000cb0 00000000
r24-27 00000000 00000000 00000000 10347010
r28-31 00000000 39387000 2fda03c0 102269ec
sr0-3 00000000 00000000 00000000 00000000
sr4-7 00000000 00000000 00000000 00000000
IASQ: 00000000 00000000 IAOQ: 101f981c 101f9820
IIR: b3202000 ISR: 00000000 IOR: 00000000
CPU: 0 CR30: 2fda0000 CR31: 103d0000
ORIG_R28: f0000074
IAOQ[0]: $$divU+0xc/0x210
IAOQ[1]: $$divU+0x10/0x210
RP(r2): serial8250_get_divisor+0x44/0x50
Kernel panic: Kernel Fault
Reply to: