I have a C240 satisfyingly running Debian Testing and kernels from 2.4.17 to 2.4.27-pa4, both stock and custom compiled. However, no variation of 2.6.x ever booted. Since the last message I see is that infamous »you may need to switch your console« I eventually organized a serial cable, a second machine running minicom and got the same result: ======================================================================== Attempting to boot Primary Path... BOOTABLE DEVICE FOUND: Path Number Device Path Device Type and Utilities ----------- ----------------- ------------------------- P0 FWSCSI.0.0 IBM DNES-309170W IPL Booting... Boot IO Dependent Code (IODC) revision 1 HARD Booted. palo ipl 1.5 root@c3k Fri May 14 16:17:38 MDT 2004 Skipping extended partition 6 - beyond reach of IPL Partition Start(MB) End(MB) Id Type 1 1 15 f0 Palo 2 16 503 83 ext2 3 504 980 82 swap 5 981 2887 83 ext2 PALO(F0) partition contains: 0/vmlinux32 4078989 bytes @ 0x44000 Information: No console specified on kernel command line. This is normal. PALO will choose the console currently used by firmware (serial). Command line for kernel: 'root=/dev/sda2 HOME=/ max_loop=64 console=ttyS0 TERM=' Selected kernel: /boot/vmlinux from partition 2 Selected ramdisk: /boot/initrd.img-2.6.8-1-32 from partition 2 ELF32 executable Entry 00100000 first 00100000 n 2 Segment 0 load 00100000 size 2265344 mediaptr 0x1000 Segment 1 load 0032c000 size 458886 mediaptr 0x22b000 Loading ramdisk 3133440 bytes @ 3fcf1000... Branching to kernel entry point 0x00100000. If this is the last message you see, you may need to switch your console. This is a common symptom -- search the FAQ and mailing list at parisc-linux.org ======================================================================== Above kernel is the stock Debian kernel-image-2.6.8-1-32. I also experimented with a few custom compiled ones (no initrd, NIC driver statically), same result. Where is this FAQ item mentioned above? And how is this ment, anyway? Just switching consoles within HP's »BIOS«, or passing some arguments via /etc/palo.conf, or compiling the kernel with different settings? I'd really like to help more, but without any diagnostics of 2.6.x ... Well, here is the start of dmesg when booting with a custom compiled kernel: ======================================================================== Linux version 2.4.27-pa4 (root@lnzx02) (gcc version 3.3.4 (Debian 1:3.3.4-13)) #1 Wed Dec 22 10:21:43 CET 2004 FP[0] enabled: Rev 0 Model 14 The 32-bit Kernel has started... Determining PDC firmware type: System Map. model 00005990 00000481 00000000 00000002 782320ae 100000f0 00000008 000000b2 000000b2 vers 00000501 CPUID vers 14 rev 23 (0x000001d7) capabilities 0x2 model 9000/782/C240+ Total Memory: 1536 Mb pagetable_init On node 0 totalpages: 393216 zone(0): 393216 pages. zone(1): 0 pages. zone(2): 0 pages. LED display at f0190001 registered Kernel command line: root=/dev/sda2 HOME=/ max_loop=64 console=tty0 sti=10/0/4/0 sti_font=VGA8x16 TERM=linux palo_kernel=2/boot/vmlinux-2.4.27-pa4 Console: colour dummy device 160x64 Calibrating delay loop... 470.22 BogoMIPS Memory: 1551652k available Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) Inode cache hash table entries: 131072 (order: 8, 1048576 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 131072 (order: 7, 524288 bytes) Page-cache hash table entries: 524288 (order: 9, 2097152 bytes) Searching for devices... Found devices: 1. U2-IOA BC Runway Port (12) at 0xfff88000 [8], versions 0x580, 0xf, 0xb 2. Dino PCI Bridge (13) at 0xf2000000 [8/0], versions 0x680, 0x3, 0xa, additional addresses: 0xf2800000 3. Raven U/L2 Dino RS-232 (10) at 0xf2003000 [8/0/63], versions 0x6, 0x0, 0x8c 4. Raven U/L2 Dino PS/2 Port (10) at 0xf2001000 [8/1], versions 0x6, 0x0, 0x96 5. Raven+ w SE FWSCSI Core BA (11) at 0xffd00000 [8/16], versions 0x56, 0x0, 0x81, additional addresses: 0xffd0c000 0xffc00000 6. Raven+ w SE FWSCSI Core Centronics (10) at 0xffd02000 [8/16/0], versions 0x56, 0x0, 0x74, additional addresses: 0xffd01000 0xffd03000 7. Raven+ w SE FWSCSI Core Audio (10) at 0xffd04000 [8/16/1], versions 0x56, 0x4, 0x7b 8. Raven+ w SE FWSCSI Core RS-232 (10) at 0xffd05000 [8/16/4], versions 0x56, 0x0, 0x8c 9. Raven+ w SE FWSCSI Core SCSI (10) at 0xffd06000 [8/16/5], versions 0x56, 0x0, 0x82 10. Raven+ w SE FWSCSI Core PS/2 Port (10) at 0xffd08000 [8/16/7], versions 0x56, 0x0, 0x84 11. Raven+ w SE FWSCSI Core PS/2 Port (10) at 0xffd08100 [8/16/8], versions 0x56, 0x0, 0x84 12. U2-IOA BC GSC+ Port (7) at 0xf203f000 [8/63], versions 0x501, 0x1, 0xc 13. U2-IOA BC Runway Port (12) at 0xfff8a000 [10], versions 0x580, 0xf, 0xb 14. Cujo PCI Bridge (13) at 0xf1000000 [10/0], versions 0x682, 0x1, 0xa, additional addresses: 0xf1800000 0xf6000000 15. Dino RS-232 (10) at 0xf1003000 [10/3], versions 0x7, 0x0, 0x8c 16. U2-IOA BC GSC+ Port (7) at 0xf103f000 [10/63], versions 0x501, 0x1, 0xc 17. Raven U 240 (9000/780/C240) (0) at 0xfffa0000 [32], versions 0x599, 0x0, 0x4 18. Memory (1) at 0xfffb1000 [49], versions 0x6f, 0x0, 0x9 CPU(s): 1 x PA8200 (PCX-U+) at 236.000000 MHz Found U2 at 0xfff88000 Found U2 at 0xfff8a000 Lasi version 0 at 0xffd00000 found. Dino version 3.1 found at 0xf2000000 Cujo version 2.0 found at 0xf1000000 Enabling Cujo 2.0 bug workaround Don't recognise Cujo at address 0xf1000000, not enabling workaround POSIX conformance testing by UNIFIX Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Soft power switch enabled, polling @ 0xf0140000. Starting kswapd Journalled Block Device driver loaded STI GSC/PCI graphics driver version 0.9 STI PCI graphic ROM found at f1e00000 (2048 kB), fb at f6000000 (32 MB) STI word mode ROM at f1e00044, hpa at f6000000 STI id 2fc1066b-9a02587, conforms to spec rev. 8.09 STI device: HPA4554A stifb: Unsupported gfx card id 0x2fc1066b ========================================================================
Attachment:
pgp5LlMc8_L1K.pgp
Description: PGP signature