Hardware not detected (9000/801/D200)
Hi there,
I've got a old D200 Server with two external SCSI disks. These disks (ST32171N) are not detected during installation.
Are there any hints ?
regards,
Frank
cfg2html (hp-ux 10.20):
---=[ Hardware with H/W-Path ]=-------------------------------------------
Class I H/W Path Driver S/W State H/W Type Description
=======================================================================
bc 0 root CLAIMED BUS_NEXUS
ba 0 16 bus_adapter CLAIMED BUS_NEXUS Core I/O Adapter
ext_bus 1 16/0 CentIf CLAIMED INTERFACE Built-in Parallel
Interface
tty 0 16/4 asio0 CLAIMED INTERFACE Built-in RS-232C
ext_bus 0 16/5 c720 CLAIMED INTERFACE Built-in SCSI
target 0 16/5.0 tgt CLAIMED DEVICE
tape 0 16/5.0.0 stape CLAIMED DEVICE HP C1533A
target 1 16/5.2 tgt CLAIMED DEVICE
disk 0 16/5.2.0 sdisk CLAIMED DEVICE TOSHIBA CD-ROM
XM-5401TA
target 2 16/5.5 tgt CLAIMED DEVICE
disk 1 16/5.5.0 sdisk CLAIMED DEVICE SEAGATE ST32550N
target 3 16/5.6 tgt CLAIMED DEVICE
disk 2 16/5.6.0 sdisk CLAIMED DEVICE SEAGATE ST32550N
target 4 16/5.7 tgt CLAIMED DEVICE
ctl 0 16/5.7.0 sctl CLAIMED DEVICE Initiator
lan 0 16/6 lan2 CLAIMED INTERFACE Built-in LAN
ps2 0 16/7 ps2 CLAIMED INTERFACE Built-in
Keyboard/Mouse
ba 1 20 bus_adapter CLAIMED BUS_NEXUS Core I/O Adapter
tty 1 20/2 asio0 CLAIMED INTERFACE Built-in RS-232C
ba 2 20/5 eisa CLAIMED BUS_NEXUS EISA Bus Adapter
ext_bus 2 20/5/1 c720 CLAIMED INTERFACE EISA card HWP0C80
target 5 20/5/1.5 tgt CLAIMED DEVICE
disk 3 20/5/1.5.0 sdisk CLAIMED DEVICE SEAGATE ST32171N
target 6 20/5/1.6 tgt CLAIMED DEVICE
disk 4 20/5/1.6.0 sdisk CLAIMED DEVICE SEAGATE ST32171N
target 7 20/5/1.7 tgt CLAIMED DEVICE
ctl 1 20/5/1.7.0 sctl CLAIMED DEVICE Initiator
processor 0 62 processor CLAIMED PROCESSOR Processor
memory 0 63 memory CLAIMED MEMORY Memory
Class I H/W Path Driver S/W State H/W Type Description
=======================================================================
bc 0 root CLAIMED BUS_NEXUS
ba 0 16 bus_adapter CLAIMED BUS_NEXUS Core I/O Adapter
ext_bus 1 16/0 CentIf CLAIMED INTERFACE Built-in Parallel
Interface
/dev/c1t0d0_lp
tty 0 16/4 asio0 CLAIMED INTERFACE Built-in RS-232C
/dev/diag/mux0 /dev/mux0 /dev/tty0p0
ext_bus 0 16/5 c720 CLAIMED INTERFACE Built-in SCSI
target 0 16/5.0 tgt CLAIMED DEVICE
tape 0 16/5.0.0 stape CLAIMED DEVICE HP C1533A
/dev/rmt/0m /dev/rmt/0mn
/dev/rmt/c0t0d0BEST /dev/rmt/c0t0d0BESTn
/dev/rmt/0mb /dev/rmt/0mnb
/dev/rmt/c0t0d0BESTb /dev/rmt/c0t0d0BESTnb
target 1 16/5.2 tgt CLAIMED DEVICE
disk 0 16/5.2.0 sdisk CLAIMED DEVICE TOSHIBA CD-ROM
XM-5401TA
/dev/dsk/c0t2d0 /dev/rdsk/c0t2d0
target 2 16/5.5 tgt CLAIMED DEVICE
disk 1 16/5.5.0 sdisk CLAIMED DEVICE SEAGATE ST32550N
/dev/dsk/c0t5d0 /dev/rdsk/c0t5d0
target 3 16/5.6 tgt CLAIMED DEVICE
disk 2 16/5.6.0 sdisk CLAIMED DEVICE SEAGATE ST32550N
/dev/dsk/c0t6d0 /dev/rdsk/c0t6d0
target 4 16/5.7 tgt CLAIMED DEVICE
ctl 0 16/5.7.0 sctl CLAIMED DEVICE Initiator
/dev/rscsi/c0t7d0
lan 0 16/6 lan2 CLAIMED INTERFACE Built-in LAN
/dev/diag/lan0 /dev/ether0 /dev/lan0
ps2 0 16/7 ps2 CLAIMED INTERFACE Built-in
Keyboard/Mouse
/dev/ps2_0 /dev/ps2_1 /dev/ps2kbd
/dev/ps2mouse
ba 1 20 bus_adapter CLAIMED BUS_NEXUS Core I/O Adapter
tty 1 20/2 asio0 CLAIMED INTERFACE Built-in RS-232C
/dev/diag/mux1 /dev/mux1 /dev/tty1p0
ba 2 20/5 eisa CLAIMED BUS_NEXUS EISA Bus Adapter
ext_bus 2 20/5/1 c720 CLAIMED INTERFACE EISA card HWP0C80
target 5 20/5/1.5 tgt CLAIMED DEVICE
disk 3 20/5/1.5.0 sdisk CLAIMED DEVICE SEAGATE ST32171N
/dev/dsk/c2t5d0 /dev/rdsk/c2t5d0
target 6 20/5/1.6 tgt CLAIMED DEVICE
disk 4 20/5/1.6.0 sdisk CLAIMED DEVICE SEAGATE ST32171N
/dev/dsk/c2t6d0 /dev/rdsk/c2t6d0
target 7 20/5/1.7 tgt CLAIMED DEVICE
ctl 1 20/5/1.7.0 sctl CLAIMED DEVICE Initiator
/dev/rscsi/c2t7d0
processor 0 62 processor CLAIMED PROCESSOR Processor
memory 0 63 memory CLAIMED MEMORY Memory
dmesg:
Linux version 2.4.17-32 (root@paer) (gcc version 3.0.4) #1 Sat Mar 16
17:09:00 MST 2002
FP[0] enabled: Rev 1 Model 13
The 32-bit Kernel has started...
Determining PDC firmware type: System Map.
model 00004850 00000481 00000000 00000000 77bc15ea 100000f0 00000004
00000072 00000072
vers 0000000c
model 9000/801/D200
Total Memory: 128 Mb
pagetable_init
On node 0 totalpages: 32768
zone(0): 32768 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/sda7 HOME=/ console=ttyS0 TERM=vt102
palo_kernel=2/vmlinux
Console: colour dummy device 160x64
Calibrating delay loop... 74.75 BogoMIPS
Memory: 125976k available
Dentry-cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode-cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
Searching for devices...
Found devices:
1. UL 350 Lasi Core BA (11) at 0xf0100000 [16], versions 0x2e, 0x0, 0x81,
additional addresses: 0xf010c000 0xf0100000
2. UL 350 Core Centronics (10) at 0xf0102000 [16/0], versions 0x2e, 0x0,
0x74, additional addresses: 0xf0101000 0xf0103000
3. UL 350 Lasi Core RS-232 (10) at 0xf0105000 [16/4], versions 0x2e, 0x0,
0x8c
4. UL 350 Core SCSI (10) at 0xf0106000 [16/5], versions 0x2e, 0x0, 0x82
5. UL 350 Core LAN (802.3) (10) at 0xf0107000 [16/6], versions 0x2e, 0x0,
0x8a
6. UL 350 Core PS/2 Port (10) at 0xf0108000 [16/7], versions 0x2e, 0x0, 0x84
7. UL 350 Core PS/2 Port (10) at 0xf0108100 [16/8], versions 0x2e, 0x0, 0x84
8. UL 350 Core Wax BA (11) at 0xffe00000 [20], versions 0x30, 0x0, 0x8e
9. UL 350 Wax Core RS-232 (10) at 0xffe02000 [20/2], versions 0x30, 0x0,
0x8c
10. UL 350 Wax EISA BA (11) at 0xfc000000 [20/5], versions 0x30, 0x0, 0x90,
additional addresses: 0xf0088000
11. Unknown machine (0) at 0xfffbe000 [62], versions 0x485, 0x0, 0x4
12. Memory (1) at 0xfffbf000 [63], versions 0x56, 0x0, 0x9
CPU(s): 1 x PA7100LC (PCX-L) at 75.000000 MHz
Lasi version 0 at 0xf0100000 found.
LED display at f010c000 registered
Wax at 0xffe00000 found.
Wax: HIL Keyboard-NMI registered.
Wax EISA Adapter found at 0xfc000000
EISA EEPROM at 0xf0088000
Enumerating EISA bus
EISA slot 1: HWP0C80 EISA IRQ 3 memory fc0d8000-fc0e0000
EISA slot 2 a configured board was not detected ( expected ___FFFF)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Enabled soft power switch (polling mode, io=0xf00a8000).
Starting kswapd
Journalled Block Device driver loaded
parport_init_chip: initialize bidirectional-mode.
parport0: PC-style at 0xf0102800, irq 88 [PCSPP,TRISTATE]
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ
SERIAL_PCI enabled
ttyS00 at iomem 0xf0105800 (irq = 90) is a 16550A
ttyS01 at iomem 0xffe02800 (irq = 121) is a 16550A
PS/2 keyboard port at 0xf0108000 (irq 69) found, no device attached.
PS/2 psaux port at 0xf0108100 (irq 69) found, no device attached.
lp0: using parport0 (interrupt-driven).
Generic RTC Driver v1.02 05/27/1999 Sam Creasey (sammy@oh.verio.com)
block: 128 slots per queue, batch=32
RAMDISK driver initialized: 16 RAM disks of 6144K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
loop: loaded (max 8 devices)
Found i82596 at 0xf0107000, IRQ 87
eth0: 82596 at 0xf0107000, 08 00 09 AE 18 68 IRQ 87.
82596.c $Revision: 1.28 $
SCSI subsystem driver Revision: 1.00
53c700: Version 2.6 By James.Bottomley@HansenPartnership.com
scsi0: 53c710 rev 2
scsi0 : LASI SCSI 53c700
scsi0: (0:0) Synchronous at offset 8, period 100ns
Vendor: HP Model: C1533A Rev: HP00
Type: Sequential-Access ANSI SCSI revision: 02
scsi0: (2:0) Synchronous at offset 8, period 236ns
Vendor: TOSHIBA Model: CD-ROM XM-5401TA Rev: 1036
Type: CD-ROM ANSI SCSI revision: 02
scsi0: (5:0) Synchronous at offset 8, period 100ns
Vendor: SEAGATE Model: ST32550N Rev: HP09
Type: Direct-Access ANSI SCSI revision: 02
scsi0: (6:0) Synchronous at offset 8, period 100ns
Vendor: SEAGATE Model: ST32550N Rev: HP09
Type: Direct-Access ANSI SCSI revision: 02
st: Version 20011103, bufsize 32768, wrt 30720, max init. bufs 4, s/g segs
16
Attached scsi tape st0 at scsi0, channel 0, id 0, lun 0
Attached scsi disk sda at scsi0, channel 0, id 5, lun 0
Attached scsi disk sdb at scsi0, channel 0, id 6, lun 0
scsi0: (5:0) Enabling Tag Command Queuing
SCSI device sda: 4165272 512-byte hdwr sectors (2133 MB)
Partition check:
sda: sda1 sda2 sda3 < sda5 sda6 sda7 >
scsi0: (6:0) Enabling Tag Command Queuing
SCSI device sdb: 4165272 512-byte hdwr sectors (2133 MB)
sdb: sdb1 sdb2 sdb3 < sdb5 sdb6 >
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 2, lun 0
sr0: scsi-1 drive
Uniform CD-ROM driver Revision: 3.12
sticonsole_init: searching for STI ROMs
BUG: Skipping previously registered driver: sti (native)
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
8regs : 56.800 MB/sec
8regs_prefetch: 56.800 MB/sec
32regs : 66.400 MB/sec
32regs_prefetch: 66.400 MB/sec
raid5: using function: 32regs_prefetch (66.400 MB/sec)
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 16384)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
NOT FREEING INITMEM (383k)
Adding Swap: 368240k swap-space (priority -1)
EXT3 FS 2.4-0.9.16, 02 Dec 2001 on sd(8,7), internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.16, 02 Dec 2001 on sd(8,2), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.16, 02 Dec 2001 on sd(8,5), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.16, 02 Dec 2001 on sd(8,6), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.16, 02 Dec 2001 on sd(8,18), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.16, 02 Dec 2001 on sd(8,21), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.16, 02 Dec 2001 on sd(8,22), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth0: link ok.
VFS: Disk change detected on device sr(11,0)
ISO 9660 Extensions: RRIP_1991A
ISO 9660 Extensions: RRIP_1991A
ISO 9660 Extensions: RRIP_1991A
VFS: Disk change detected on device sr(11,0)
ISO 9660 Extensions: RRIP_1991A
VFS: Disk change detected on device sr(11,0)
ISO 9660 Extensions: RRIP_1991A
SysRq : HELP : loglevel0-8 reBoot tErm kIll saK killalL showMem showPc unRaw
Sync showTasks Unmount
Reply to: