Re: debian sur sparc
salut a tous
je bloque encore.
c'est une potato 2.2r2 sparc
quand je lance startx :
tempete:/etc# startx
(using VT number 7)
Xconnection to :0.0 broken (explicit kill or server shutdown)
avec xinit, pareil.
je suis pas sur de mon XF86Config (il est en attachment)
si quelqu'un pouvait m'envoyer le sien.
merci
# XF86Config file preconfigured for SPARC machines
Section "Files"
RgbPath "/usr/X11R6/lib/X11/rgb"
FontPath "/usr/lib/X11/fonts/misc/:unscaled"
FontPath "/usr/lib/X11/fonts/cyrillic/:unscaled"
FontPath "/usr/lib/X11/fonts/100dpi/:unscaled"
FontPath "/usr/lib/X11/fonts/75dpi/:unscaled"
FontPath "/usr/lib/X11/fonts/Speedo/"
FontPath "/usr/lib/X11/fonts/Type1/"
FontPath "/usr/lib/X11/fonts/misc/"
FontPath "/usr/lib/X11/fonts/cyrillic/"
FontPath "/usr/lib/X11/fonts/100dpi/"
FontPath "/usr/lib/X11/fonts/75dpi/"
EndSection
Section "ServerFlags"
#NoTrapSignals
#DontZap
#DontZoom
EndSection
Section "Keyboard"
Protocol "Standard"
# AutoRepeat 500 5
# Let the server do the NumLock processing. This should only be
# required when using pre-R6 clients.
#ServerNumLock
# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
#Xleds 1 2 3
LeftAlt Meta
RightAlt Meta
ScrollLock Compose
RightCtl Control
# To disable the XKEYBOARD (XKB) extension, uncomment XkbDisable. When not
# using XKB, the server often guesses the console keymap incorrectly;
# uncomment appropriate lines in /etc/X11/Xmodmap to fix it.
XkbDisable
# The following works for a Type 5 North American keyboard.
# XKB is extremely poorly documented (thanks, SGI!). Good luck.
# XkbModel "sun"
# XkbKeycodes "sun(type5)"
# PC (PS/2) keyboard users (North America)
# XkbRules "xfree86"
# XkbModel "pc104"
# XkbLayout "us"
EndSection
# **********************************************************************
# Pointer section
# **********************************************************************
Section "Pointer"
Protocol "sun"
# The mouse is most likely located at one of three places:
Device "/dev/sunmouse" # traditional Sun mouse
# Device "/dev/mouse" # usually a symlink to the real device
# Device "/dev/misc/sunmouse" # devfs location
# For PS/2 systems, you should install GPM, use mouse type "ps2" (or
# whatever protocol is appropriate for your mouse), set up the repeater
# for "raw", then uncomment these settings
# Protocol "ps/2"
# Device "/dev/gpmdata"
EndSection
# **********************************************************************
# Monitor section
# **********************************************************************
# any number of monitor sections may be present
Section "Monitor"
Identifier "Generic Monitor"
VendorName "Unknown"
ModelName "Unknown"
# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
HorizSync 31.5-80
# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
VertRefresh 50-120
# Sun Microsystems Modes
# The third number in the mode name is the vertical refresh rate.
ModeLine "1152x900x66" 94.5 1152 1192 1320 1528 900 902 906 937 -hsync -vsync
ModeLine "1152x900x76" 108.0 1152 1184 1312 1504 900 902 906 937 -hsync -vsync
ModeLine "1280x1024x67" 117.0 1280 1296 1408 1632 1024 1026 1034 1067 -hsync -vsync
ModeLine "1280x1024x76" 135.0 1280 1312 1376 1664 1024 1026 1034 1066 -hsync -vsync
EndSection
# **********************************************************************
# Graphics device section
# **********************************************************************
# any number of graphics device sections may be present
Section "Device"
Identifier "Generic Video Card"
VendorName "Unknown"
BoardName "Unknown"
VideoRam 4096
# Insert Clocks lines here if appropriate
EndSection
# **********************************************************************
# Screen sections
# **********************************************************************
# the Mach64 or 3DLabs/GLINT accelerated server
Section "Screen"
Driver "accel"
Device "Generic Video Card"
Monitor "Generic Monitor"
Subsection "Display"
Depth 8
Modes "1152x900x76"
ViewPort 0 0
Virtual 1152 900
EndSubsection
EndSection
Reply to: