[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Bug#609466: marked as done ([SPARC] console [tty0] enabled, bootconsole disabled)

Your message dated Sun, 20 Mar 2011 18:30:42 +0000
with message-id <201103201830.42290.elmig@debianpt.org>
and subject line 
has caused the Debian Bug report #609466,
regarding [SPARC] console [tty0] enabled, bootconsole disabled
to be marked as done.

This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.

(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact owner@bugs.debian.org
immediately.)


-- 
609466: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=609466
Debian Bug Tracking System
Contact owner@bugs.debian.org with problems
--- Begin Message --- 
Package: installation-reports

Boot method: <How did you boot the installer? CD
Image version: <Full URL to image you downloaded is best> http://cdimage.debian.org/debian-cd/5.0.7/sparc/iso-cd/debian-507-sparc-CD-1.iso
Date: <Date and time of the install> 2011-01-09

Machine: <Description of machine (eg, IBM Thinkpad R32)> Sun Sparc Ultra 10
Processor: Ultra SPARC IIi 333 MHZ
Memory: 1GB
Partitions: <df -Tl will do; the raw partition table is preferred> ? didn't go that far

Output of lspci -knn (or lspci -nn): didn't go that far

Base System Installation Checklist: E
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it

Initial boot:           [ ]
Detect network card:    [ ]
Configure network:      [ ]
Detect CD:              [ ]
Load installer modules: [ ]
Detect hard drives:     [ ]
Partition hard drives:  [ ]
Install base system:    [ ]
Clock/timezone setup:   [ ]

 
 
User/password setup:    [ ]
Install tasks:          [ ]
Install boot loader:    [ ]
Overall install:        [ ]

Comments/Problems:

<Description of the install, in prose, and any thoughts, comments
      and ideas you had during the initial install.>

start to boot and prints lots of messages on screen, but then stops
the last messages are
[0.000000] Booting Linux...
[0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130071
[0.000000] Kernel command line:
[0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[0.000000] clocksource: mult[300c5] shift[16]
[0.000000] clockevent: mult[553f7ced] shift[32]
[42.966816] Console: colour dummy device 80x25
[43.020133] console handover: boot [earlyprom0] -> real [tty0]
after this nothing seems to happen
 
I have previously been running Sarge and FreeBSD 8.1 so the hardware should be fine.
rescue mode has the same problem, expert mode has the same problem
 
The following image has a similar problem, the error message is a bit different, but stops when doing something with the console
http://cdimage.debian.org/debian-cd/5.0.7/sparc/iso-cd/debian-507-sparc-businesscard.iso
last line is: 
[0.000000] console [tty0] enabled, bootconsole disabled
 
 
 

--- End Message ---
--- Begin Message --- 
Fixed in Debian 6.0.1 full images with linux-2.6_2.6.32-31.

--- End Message ---
Reply to: