--- Begin Message ---
- To: <submit@bugs.debian.org>
- Subject: [i386][netinst][beta3] failure: Dell Inspiron i7000 (2nd attempt)
- From: Vincent McIntyre <Vince.McIntyre@atnf.csiro.au>
- Date: Mon, 18 Sep 2006 23:09:58 +1000 (EST)
- Message-id: <Pine.SOL.4.33.0609182308270.20530-100000@venice.tip.CSIRO.AU>
Package: installation-reports
INSTALL REPORT
Debian-installer-version:
http://cdimage.debian.org/cdimage/etch_di_beta3/i386/iso-cd/debian-testing-i386-netinst.iso
uname -a:
Linux tinsley 2.6.16-2-686 #1 Fri Aug 18 19:01:49 UTC 2006 i686 GNU/Linux
Date: 2006-08-23T22_00_00+1000
Method:
How did you install? boot with "install" from netinst cdrom
What did you boot off? netinst cdrom
If network install, from where? n/a
Proxied? no
Machine: Dell Inspiron i7000
Processor: Intel(R) Celeron(Mendocino) CPU 367MHz
Memory: 127220 kB
Root Device: IDE, /dev/hda
Root Size/partition table:
(fdisk -l /dev/hda)
Disk /dev/hda: 60.0 GB, 60011642880 bytes
255 heads, 63 sectors/track, 7296 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/hda1 * 1 34 273073+ 83 Linux
/dev/hda2 35 7296 58332015 5 Extended
/dev/hda5 35 642 4883728+ 83 Linux
/dev/hda6 643 1007 2931831 83 Linux
/dev/hda7 1008 1069 497983+ 82 Linux swap / Solaris
/dev/hda8 1070 1131 497983+ 83 Linux
/dev/hda9 1132 2347 9767488+ 83 Linux
/dev/hda10 2348 7296 39752811 83 Linux
/etc/fstab:
# <file system> <mount point> <type> <options> <dump> <pass>
proc /proc proc defaults 0 0
/dev/hda1 / ext3 defaults,errors=remount-ro 0 1
/dev/hda10 /data ext3 defaults 0 2
/dev/hda9 /home ext3 defaults 0 2
/dev/hda8 /tmp ext3 defaults 0 2
/dev/hda5 /usr ext3 defaults 0 2
/dev/hda6 /var ext3 defaults 0 2
/dev/hda7 none swap sw 0 0
/dev/hdc /media/cdrom0 udf,iso9660 user,noauto 0 0
/dev/fd0 /media/floppy0 auto rw,user,noauto 0 0
Output of lspci and lspci -n:
00:00.0 0600: 8086:7190 (rev 03)
00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
00:01.0 0604: 8086:7191 (rev 03)
00:01.0 PCI bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03)
00:04.0 0607: 104c:ac17 (rev 02)
00:04.0 CardBus bridge: Texas Instruments PCI1220 (rev 02)
00:04.1 0607: 104c:ac17 (rev 02)
00:04.1 CardBus bridge: Texas Instruments PCI1220 (rev 02)
00:07.0 0680: 8086:7110 (rev 02)
00:07.0 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 02)
00:07.1 0101: 8086:7111 (rev 01)
00:07.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01)
00:07.2 0c03: 8086:7112 (rev 01)
00:07.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev 01)
00:07.3 0680: 8086:7113 (rev 02)
00:07.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 02)
00:08.0 0401: 125d:1968
00:08.0 Multimedia audio controller: ESS Technology ES1968 Maestro 2
01:00.0 0300: 1002:4c42 (rev dc)
01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage LT Pro AGP-133 (rev dc)
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [O]
Configure network HW: [O]
Config network: [O] *
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Create file systems: [O]
Mount partitions: [O]
Install base system: [E]
Install boot loader: [ ]
Reboot: [ ]
Comments/Problems:
Things went pretty well at first, thanks for your great work.
A couple of issues cropped up however.
[bug] kernel does not fully support TOSHIBA DVD-ROM SD-C2202
This may be specific to the d-i kernel; I have never noticed this problem
since completing the installation via a 2.4 kernel and then upgrading to
2.6.16. Oh, the problem:
I was unable to install a 2.6 kernel directly with the 'install' boot item.
It would repeatedly fail during installation of the base system with the error
hdc command error: status=0x51 { DriveReady SeekCompleteError} {IllegalLengthIndication LastFailedSense=0x05 }
ide: failed opcode was: unknown
end-request: I/O error, dev hdc, sector 3880
Buffer I/O error on device hdc, logical block 970
This would happen at different times during base installation. The status
would always be 0x51 but the sectore would change.
On noticing the failure I went into the shell on VT2 and tried manually
mounting. I was able to get the cdrom to remount with:
umount /cdrom
mount -t iso9660 -oro /dev/cdrom/cdrom0 /cdrom
ls /cdrom
On some of the umount/mount cycles I noticed that the 'etch' directory
was missing from /cdrom/dists/, but then it would return after another
umount/mount cycle.
I kept plugging away at this until the system locked up completely
and I had to abort, after about 3 or 4 cycles.
[wishlist]
Please consider always displaying the ESSID during wireless network config.
I had a small network glitch; I have a wireless router that does not broadcast
the ESSID, but a neighbour has one which does broadcast and the installer
latched on to that by default. I didn't want to suck up his bandwidth, so
this wasn't an appropriate default.
Causing the installer to Go Back out of this step and start it again caused
it to do the Right Thing, ie lowered the priority threshold enough so d-i
asked me for the correct ESSID to use. But I think it would be better if
d-i explained which ESSID it found and then always asked if that is the
correct one to use. In the usual case it is just one extra 'ok' from the
end user, and it allows correct handling of unusual cases.
lsmod output:
Module Size Used by
dm_snapshot 15324 0
dm_mirror 17236 0
apm 18380 1
usbhid 32128 0
sd_mod 16208 0
usb_storage 69312 0
scsi_mod 122220 2 sd_mod,usb_storage
ipv6 217760 16
dm_mod 47892 2 dm_snapshot,dm_mirror
loop 14472 0
hostap_cs 53588 0
hostap 99140 1 hostap_cs
ieee80211_crypt 5312 1 hostap
orinoco_cs 16420 1
orinoco 34452 1 orinoco_cs
hermes 7136 2 orinoco_cs,orinoco
radio_maestro 6656 0
compat_ioctl32 1184 1 radio_maestro
videodev 8640 1 radio_maestro
joydev 8864 0
mousedev 10368 1
pcmcia 34844 2 hostap_cs,orinoco_cs
tsdev 7200 0
firmware_class 9472 1 pcmcia
snd_es1968 25600 1
i2c_piix4 8080 0
shpchp 39200 0
pci_hotplug 24180 1 shpchp
gameport 13480 1 snd_es1968
i2c_core 19312 1 i2c_piix4
snd_ac97_codec 82784 1 snd_es1968
snd_ac97_bus 2048 1 snd_ac97_codec
snd_pcm 74408 2 snd_es1968,snd_ac97_codec
snd_timer 20292 1 snd_pcm
snd_page_alloc 9800 2 snd_es1968,snd_pcm
snd_mpu401_uart 6592 1 snd_es1968
snd_rawmidi 22048 1 snd_mpu401_uart
snd_seq_device 8236 1 snd_rawmidi
snd 46080 9 snd_es1968,snd_ac97_codec,snd_pcm,snd_timer,snd_
mpu401_uart,snd_rawmidi,snd_seq_device
intel_agp 20860 1
soundcore 8672 1 snd
agpgart 29232 1 intel_agp
evdev 8736 0
yenta_socket 23660 4
rsrc_nonstatic 11840 1 yenta_socket
pcmcia_core 37264 3 pcmcia,yenta_socket,rsrc_nonstatic
psmouse 34248 0
serio_raw 6436 0
parport_pc 31472 0
parport 31720 1 parport_pc
rtc 11252 0
pcspkr 2948 0
floppy 55628 0
ext3 116008 6
jbd 46932 1 ext3
mbcache 7652 1 ext3
ide_cd 35328 0
cdrom 31888 1 ide_cd
ide_disk 14528 8
piix 8932 0 [permanent]
generic 4164 0 [permanent]
ide_core 111440 5 usb_storage,ide_cd,ide_disk,piix,generic
uhci_hcd 26640 0
usbcore 110560 4 usbhid,usb_storage,uhci_hcd
processor 21696 0
--- End Message ---
--- Begin Message ---
We are closing this installation report for one of the following
reasons:
- it was reported with a pre-lenny version of Debian
Installer.
- indications in the installation report give the feeling that
the reported problem waslying in another software, unrelated to
D-I, which we can't easily identify.
- indications in the installation report suggest that it may have been
fixed in a more recent version of a D-I component
- it was successful and we forgot closing it..:-)
- it has no information we consider useful
The D-I team is currently in the process of cleaning out the old spool
of installation reports that haven't bene processed yet.
In case you think that the problem you reported has chances to be
still present, please reiterate your installation test with
a more recent image of D-I, if you're in position of doing this.
You'll find daily builds at
http://www.debian.org/devel/debian-installer. We recommend you choose
the netboot image, in the "daily builds section", then choose to
install "squeeze" when prompted.
If some problems are found, please report them with a new bug sent
against installation-reports.
Many thanks for your understanding and your help improving Debian,
past and present.
--- End Message ---