--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Cc: georg@f-451.net
- Subject: installation-reports: [i386][20040723][netinst] general success
- From: Georg Neis <georg@f-451.net>
- Date: Sun, 25 Jul 2004 01:01:57 +0200
- Message-id: <20040724230157.GC3042@georg.eisfair.net>
Package: installation-reports
Debian-installer-version:
- downloaded on 2004-07-24 from .../daily/i386/current/sarge-i386-netinst.iso
- MD5: 91a392498c5c5086f25a24e73dafec62
- setup says: built on 20040723
uname -a:
Linux beteigeuze 2.6.7-1-386 #1 Thu Jul 8 05:08:04 EDT 2004 i686 GNU/Linux
Date:
2004-07-24
Method:
I booted from the netinst CD without problems (both with "linux"
and "linux26"). I did a network installation over http from
ftp.de.debian.org (no proxy, using a gateway in my LAN).
Machine:
Dell Inspiron 8200 (Notebook)
Processor:
processor : 0
vendor_id : GenuineIntel
cpu family : 15
model : 2
model name : Mobile Intel(R) Pentium(R) 4 - M CPU 1.70GHz
stepping : 7
cpu MHz : 1695.039
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe cid
bogomips : 3358.72
Memory:
MemTotal: 257324 kB
MemFree: 25912 kB
Buffers: 3608 kB
Cached: 197916 kB
SwapCached: 0 kB
Active: 143492 kB
Inactive: 67152 kB
HighTotal: 0 kB
HighFree: 0 kB
LowTotal: 257324 kB
LowFree: 25912 kB
SwapTotal: 601632 kB
SwapFree: 601632 kB
Dirty: 248 kB
Writeback: 0 kB
Mapped: 19652 kB
Slab: 16756 kB
Committed_AS: 15844 kB
PageTables: 316 kB
VmallocTotal: 778160 kB
VmallocUsed: 3120 kB
VmallocChunk: 774720 kB
Root Device:
/dev/hda, IDE, 30 GB
Some info from dmesg:
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH3M: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ICH3M: chipset revision 2
ICH3M: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xbfa0-0xbfa7, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xbfa8-0xbfaf, BIOS settings: hdc:pio, hdd:pio
hda: IC25N030ATCS04-0, ATA DISK drive
hdb: HL-DT-STDVD-ROM GDR8081N, ATAPI CD/DVD-ROM drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 58605120 sectors (30005 MB) w/1768KiB Cache, CHS=58140/16/63, UDMA(100)
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4
Root Size/partition table:
fdisk output:
Disk /dev/hda: 30.0 GB, 30005821440 bytes
16 heads, 63 sectors/track, 58140 cylinders
Units = cylinders of 1008 * 512 = 516096 bytes
Device Boot Start End Blocks Id System
/dev/hda1 1 16257 8193149+ 7 HPFS/NTFS
/dev/hda2 16257 29820 6835752 83 Linux
/dev/hda3 29820 56947 13672008 83 Linux
/dev/hda4 56947 58140 601650 82 Linux swap
mount output:
/dev/hda2 on / type unknown (rw,errors=remount-ro)
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
devpts on /dev/pts type devpts (rw,gid=5,mode=620)
tmpfs on /dev/shm type tmpfs (rw)
/dev/hda3 on /home type ext2 (rw)
usbfs on /proc/bus/usb type usbfs (rw)
While partitioning, I've got error messages saying that parted
failed to resize my partition(s) - although I didn't want to
resize anything (the partitions existed before, I only wanted to
format hda2). However, these error messages were labeled "NOT YET
IMPLEMENTED" iirc.
In the german translation, the phrase "Führe Partitionierung" (iirc)
is quite confusing.
Output of lspci:
0000:00:00.0 Host bridge: Intel Corp. 82845 845 (Brookdale) Chipset Host Bridge (rev 04)
0000:00:01.0 PCI bridge: Intel Corp. 82845 845 (Brookdale) Chipset AGP Bridge (rev 04)
0000:00:1d.0 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #1) (rev 02)
0000:00:1d.2 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #3) (rev 02)
0000:00:1e.0 PCI bridge: Intel Corp. 82801BAM/CAM PCI Bridge (rev 42)
0000:00:1f.0 ISA bridge: Intel Corp. 82801CAM ISA Bridge (LPC) (rev 02)
0000:00:1f.1 IDE interface: Intel Corp. 82801CAM IDE U100 (rev 02)
0000:00:1f.5 Multimedia audio controller: Intel Corp. 82801CA/CAM AC'97 Audio Controller (rev 02)
0000:00:1f.6 Modem: Intel Corp. 82801CA/CAM AC'97 Modem Controller (rev 02)
0000:01:00.0 VGA compatible controller: nVidia Corporation NV17 [GeForce4 440 Go] (rev a3)
0000:02:00.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78)
0000:02:01.0 CardBus bridge: Texas Instruments PCI4451 PC card Cardbus Controller
0000:02:01.1 CardBus bridge: Texas Instruments PCI4451 PC card Cardbus Controller
0000:02:01.2 FireWire (IEEE 1394): Texas Instruments PCI4451 IEEE-1394 Controller
Base System Installation Checklist:
Initial boot worked: [O]
Configure network HW: [O]
(detected both my 3c905 and my Cisco Aironet 350)
Config network: [O]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Create file systems: [O]
Mount partitions: [O]
Install base system: [O]
Install boot loader: [O]
Reboot: [O]
Comments/Problems:
- It's very good that you can always go <back> to the previous step
of the installation process!
- When I played around a little bit, sometimes something went wrong
and I landed in the main menu. From then on I had to manually
select all the remaining installation steps one after one.
- I had some troubles with xserver-xfree86: the mouse detection
seemed frozen. I've just analysed this by running "time mdetect
-v -v -v": mdetect hangs over 5 minutes after printing "Opening
device ttyS1..." and then exits with code 2 (see manpage).
Note: my mouse is actually a touchpad. It works under X with
protocol PS/2 and device /dev/psaux.
- On every boot, there are some error messages:
Starting hotplug subsystem:
[...]
isapnp
PNP0A03: can't be loaded
PNP0C01: can't be loaded
PNP0A03: can't be loaded
PNP0000: can't be loaded
PNP0100: can't be loaded
PNP0200: can't be loaded
PNP0303: can't be loaded
[...]
input: PC Speaker
PNP0800: loaded sucessfully
PNP0B00: loaded sucessfully
PNP0C04: can't be loaded
PNP0E03: can't be loaded
PNP0E00: can't be loaded
PNP0501: can't be loaded
SMCF010: can't be loaded
[...]
modprobe: FATAL: Error inserting pciehp (/lib/modules/2.6.7-1-386/kernel/drivers/pci/hotplug/pciehp.ko): Operation not permitted
pciehp: can't be loaded
missing kernel or user mode driver pciehp
[...]
modprobe: FATAL: Error inserting shpchp (/lib/modules/2.6.7-1-386/kernel/drivers/pci/hotplug/shpchp.ko): Operation not permitted
shpchp: can't be loaded
missing kernel or user mode driver shpchp
[...]
modprobe: FATAL: Error inserting shpchp (/lib/modules/2.6.7-1-386/kernel/drivers/char/hw_random.ko): Operation not permitted
hw_random: can't be loaded
missing kernel or user mode driver hw_random
[...]
These files exist; the error messages of modprobe repeat a few
times.
Attached is the output of dmesg and lsmod.
Gruß, Georg
--
The Law of Fives is never wrong.
Linux version 2.6.7-1-386 (dilinger@toaster.hq.voxel.net) (gcc version 3.3.4 (Debian 1:3.3.4-2)) #1 Thu Jul 8 05:08:04 EDT 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 0000000000100000 - 000000000ffe2800 (usable)
BIOS-e820: 000000000ffe2800 - 0000000010000000 (reserved)
BIOS-e820: 00000000feda0000 - 00000000fee00000 (reserved)
BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
255MB LOWMEM available.
On node 0 totalpages: 65506
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 61410 pages, LIFO batch:14
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
Dell Inspiron with broken BIOS detected. Refusing to enable the local APIC.
ACPI: RSDP (v000 DELL ) @ 0x000fde50
ACPI: RSDT (v001 DELL CPi R 0x27d40107 ASL 0x00000061) @ 0x000fde64
ACPI: FADT (v001 DELL CPi R 0x27d40107 ASL 0x00000061) @ 0x000fde90
ACPI: DSDT (v001 INT430 SYSFexxx 0x00001001 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
Built 1 zonelists
Kernel command line: root=/dev/hda2 ro
Initializing CPU#0
PID hash table entries: 1024 (order 10: 8192 bytes)
Detected 1694.945 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Memory: 252512k/262024k available (1309k kernel code, 8768k reserved, 701k data, 204k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3350.52 BogoMIPS
Security Scaffold v1.0.0 initialized
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: bfebf9ff 00000000 00000000 00000000
CPU: After vendor identify, caps: bfebf9ff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After all inits, caps: bfebf9ff 00000000 00000000 00000080
CPU: Intel Mobile Intel(R) Pentium(R) 4 - M CPU 1.70GHz stepping 07
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
checking if image is initramfs...it isn't (ungzip failed); looks like an initrd
Freeing initrd memory: 4252k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfbfee, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: IRQ9 SCI: Edge set to Level Trigger.
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *11
ACPI: PCI Interrupt Link [LNKC] (IRQs 9 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 9 10 *11)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT]
ACPI: Power Resource [PADA] (on)
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fe2d0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xe2f4, dseg 0x40
pnp: 00:01: ioport range 0x800-0x85f has been reserved
pnp: 00:01: ioport range 0x860-0x87f has been reserved
pnp: 00:01: ioport range 0x880-0x8bf has been reserved
pnp: 00:01: ioport range 0x8c0-0x8ff has been reserved
pnp: 00:01: ioport range 0x3f0-0x3f1 has been reserved
pnp: 00:01: ioport range 0x900-0x90f has been reserved
pnp: 00:01: ioport range 0x910-0x91f has been reserved
pnp: 00:02: ioport range 0xbf40-0xbf5f has been reserved
pnp: 00:02: ioport range 0xbf20-0xbf3f has been reserved
PnPBIOS: 16 nodes reported by PnP BIOS; 16 recorded by driver
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 7
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
PCI: Using ACPI for IRQ routing
PCI: Cannot allocate resource region 4 of device 0000:00:1d.2
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
EISA: Probing bus 0 at eisa0
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S1 S3 S4 S4bios S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4252 blocks [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 204k freed
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH3M: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ICH3M: chipset revision 2
ICH3M: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xbfa0-0xbfa7, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xbfa8-0xbfaf, BIOS settings: hdc:pio, hdd:pio
hda: IC25N030ATCS04-0, ATA DISK drive
hdb: HL-DT-STDVD-ROM GDR8081N, ATAPI CD/DVD-ROM drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 58605120 sectors (30005 MB) w/1768KiB Cache, CHS=58140/16/63, UDMA(100)
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4
Adding 601632k swap on /dev/hda4. Priority:-1 extents:1
Real Time Clock Driver v1.12
hdb: ATAPI 24X DVD-ROM drive, 512kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
Capability LSM initialized
Linux agpgart interface v0.100 (c) Dave Jones
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
PCI: Enabling device 0000:02:01.0 (0000 -> 0002)
Yenta: CardBus bridge found at 0000:02:01.0 [1028:00d4]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:01.0, mfunc 0x05033002, devctl 0x64
Yenta: ISA IRQ mask 0x0438, PCI irq 11
Socket status: 30000010
PCI: Enabling device 0000:02:01.1 (0000 -> 0002)
Yenta: CardBus bridge found at 0000:02:01.1 [1028:00d4]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:01.1, mfunc 0x05033002, devctl 0x64
Yenta: ISA IRQ mask 0x0438, PCI irq 11
Socket status: 30000006
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:02:00.0: 3Com PCI 3c905C Tornado at 0xec80. Vers LK1.1.19
Intel 810 + AC97 Audio, version 1.01, 05:24:52 Jul 8 2004
PCI: Setting latency timer of device 0000:00:1f.5 to 64
i810: Intel ICH3 found at IO 0xdc80 and 0xd800, MEM 0x0000 and 0x0000, IRQ 7
i810_audio: Audio Controller supports 6 channels.
i810_audio: Defaulting to base 2 channel mode.
i810_audio: Resetting connection 0
ac97_codec: AC97 Audio codec, id: CRY91 (Unknown)
i810_audio: AC'97 codec 0 supports AMAP, total channels = 2
i810_audio: setting clocking to 48607
input: PS/2 Generic Mouse on isa0060/serio1
mice: PS/2 mouse device common for all mice
input: PC Speaker
ts: Compaq touchscreen protocol output
irda_init()
NET: Registered protocol family 23
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
parport0: irq 7 in use, resorting to polled operation
inserting floppy driver for 2.6.7-1-386
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
agpgart: Detected an Intel i845 Chipset.
agpgart: Maximum main memory to use for agp memory: 203M
agpgart: AGP aperture is 64M @ 0xe8000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
uhci_hcd 0000:00:1d.0: Intel Corp. 82801CA/CAM USB (Hub #1)
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 11, io base 0000bf80
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: Intel Corp. 82801CA/CAM USB (Hub #3)
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 11, io base 00001000
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
hw_random: RNG not detected
PCI: Setting latency timer of device 0000:00:1f.6 to 64
MC'97 1 converters and GPIO not ready (0xff00)
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1223 $ Ben Collins <bcollins@debian.org>
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[11] MMIO=[f8fff000-f8fff7ff] Max Packet=[2048]
ieee1394: Host added: ID:BUS[0-00:1023] GUID[354fc0000a8cc810]
ip1394: $Rev: 1224 $ Ben Collins <bcollins@debian.org>
ip1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
cs: IO port probe 0x0100-0x04ff: excluding 0x170-0x177 0x280-0x287 0x370-0x37f 0x4d0-0x4d7
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
airo: Probing for PCI adapters
airo: Finished probing for PCI adapters
airo: cmd= 111
airo: status= 7f11
airo: Rsp0= 2
airo: Rsp1= 0
airo: Rsp2= 0
airo: Doing fast bap_reads
airo: MAC enabled eth2 0:c:85:64:25:45
eth2: index 0x05: Vcc 5.0, Vpp 5.0, irq 3, io 0x0100-0x013f
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02c3f00(lo)
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
eth0: no IPv6 routers present
Module Size Used by
af_packet 20616 0
ipv6 221152 10
ds 17540 4
eth1394 19464 0
ohci1394 32004 0
ieee1394 100536 2 eth1394,ohci1394
snd_intel8x0m 18632 0
snd_intel8x0 33068 0
snd_ac97_codec 59268 2 snd_intel8x0m,snd_intel8x0
snd_pcm 85412 2 snd_intel8x0m,snd_intel8x0
snd_timer 23172 1 snd_pcm
snd_page_alloc 11144 3 snd_intel8x0m,snd_intel8x0,snd_pcm
gameport 4736 1 snd_intel8x0
snd_mpu401_uart 7296 1 snd_intel8x0
snd_rawmidi 23232 1 snd_mpu401_uart
snd_seq_device 7944 1 snd_rawmidi
snd 50148 8 snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi,snd_seq_device
uhci_hcd 29200 0
usbcore 100704 3 uhci_hcd
pci_hotplug 30640 0
intel_agp 17948 1
floppy 54996 0
parport_pc 31552 0
parport 37320 1 parport_pc
irtty_sir 8320 0
sir_dev 18092 1 irtty_sir
irda 167744 2 irtty_sir,sir_dev
tsdev 7168 0
pcspkr 3816 0
mousedev 9996 0
psmouse 17800 0
evdev 9088 0
i810_audio 30356 0
ac97_codec 16908 1 i810_audio
soundcore 9824 2 snd,i810_audio
3c59x 36520 0
yenta_socket 19072 0
pcmcia_core 60484 2 ds,yenta_socket
agpgart 31272 1 intel_agp
capability 4872 0
commoncap 7168 1 capability
ide_cd 38916 0
cdrom 35360 1 ide_cd
rtc 12088 0
ide_disk 16640 4
ide_generic 1664 0
piix 12448 1
ide_core 127448 4 ide_cd,ide_disk,ide_generic,piix
unix 25776 12
font 8576 0
vesafb 6688 0
cfbcopyarea 3840 1 vesafb
cfbimgblt 3200 1 vesafb
cfbfillrect 3712 1 vesafb
--- End Message ---