[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Bug#481604: daily armel (EABI) lenny on NSLU2



Package: installation-reports
Version: 2.32
Severity: wishlist

Boot method: network (built-in nic)
Image version: http://people.debian.org/~joeyh/d-i/armel/images/daily/ixp4xx/netboot/di-nslu2.bin (2008-05-13)
Date: 2008-05-16

Machine: Linksys NSLU2
Partitions:

Disk /dev/sda: 2048 MB, 2048729600 bytes
255 heads, 63 sectors/track, 249 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x0007a76f

   Device Boot      Start         End      Blocks   Id  System
/dev/sda1   *           1         237     1903671   83  Linux
/dev/sda2             238         249       96390    5  Extended
/dev/sda5             238         249       96358+  82  Linux swap / Solaris

Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it

Initial boot:           [O] nic firmware a bit tricky
Detect network card:    [O]
Configure network:      [O]
Detect CD:              [ ]
Load installer modules: [O]
Detect hard drives:     [O]
Partition hard drives:  [O]
Install base system:    [E] locales stuck
Clock/timezone setup:   [O]
User/password setup:    [O]
Install tasks:          [ ]
Install boot loader:    [O]
Overall install:        [O]

Comments/Problems:

First, I downloaded the daily built armel image, as I wanted EABI. Then,
I embedded the NIC firmware in it taken from another image, according to
the instructions at <http://www.nslu2-linux.org/wiki/Debian/BuildImage>.
This procedure could have been easier. Perhaps a script to embed the
firmware.

I then followed tbm's instructions at
<http://www.cyrius.com/debian/nslu2/install.html> which went mostly
well. The only glitch was that locale generation seemed to take forever,
and I had to log in to a separate shell and kill the processes. This
might have been my fault though, for selecting too many locales to
generate. Also, I might not have been patient enough. I did note however
that it only stuck on the UTF-8 locales, not the ISO-8859-x ones.

Apart from this, everything went fine and the system booted up after
installation.

-- 

Please make sure that the hardware-summary log file, and any other
installation logs that you think would be useful are attached to this
report. Please compress large files using gzip.

Once you have filled out this report, mail it to submit@bugs.debian.org.

==============================================
Installer lsb-release:
==============================================
DISTRIB_ID=Debian
DISTRIB_DESCRIPTION="Debian GNU/Linux installer"
DISTRIB_RELEASE="lenny (installer build 20080513-09:31)"
X_INSTALLATION_MEDIUM=netboot

==============================================
Installer hardware-summary:
==============================================
umame -a: Linux slug 2.6.24-1-ixp4xx #1 Mon Apr 21 00:44:03 UTC 2008 armv5tel unknown
lspci -knn: 00:01.0 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 43)
lspci -knn: 	Kernel driver in use: ohci_hcd
lspci -knn: 00:01.1 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 43)
lspci -knn: 	Kernel driver in use: ohci_hcd
lspci -knn: 00:01.2 USB Controller [0c03]: NEC Corporation USB 2.0 [1033:00e0] (rev 04)
lspci -knn: 	Kernel driver in use: ehci_hcd
lsmod: Module                  Size  Used by
lsmod: reiserfs              259572  0 
lsmod: ext3                  138056  1 
lsmod: jbd                    49748  1 ext3
lsmod: vfat                   13024  0 
lsmod: fat                    55228  1 vfat
lsmod: ext2                   73320  0 
lsmod: mbcache                 9088  2 ext3,ext2
lsmod: sd_mod                 26896  3 
lsmod: usb_storage            84103  2 
lsmod: scsi_mod              120276  2 sd_mod,usb_storage
lsmod: ohci_hcd               21284  0 
lsmod: ehci_hcd               34252  0 
lsmod: evdev                  11520  0 
lsmod: ixp4xx_beeper           3488  0 
lsmod: ixp4xx_eth             16088  0 
lsmod: ixp4xx_npe              8608  2 ixp4xx_eth
lsmod: firmware_class         10048  1 ixp4xx_npe
lsmod: ixp4xx_qmgr             6040  6 ixp4xx_eth
lsmod: usbcore               139000  4 usb_storage,ohci_hcd,ehci_hcd
df: Filesystem           1k-blocks      Used Available Use% Mounted on
df: tmpfs                    14848        16     14832   0% /dev
df: tmpfs                    14848        16     14832   0% /dev
df: /dev/sda1              1873740    322200   1456360  18% /target
df: /dev/sda1              1873740    322200   1456360  18% /dev/.static/dev
df: tmpfs                    14848        16     14832   0% /target/dev
free:               total         used         free       shared      buffers
free:   Mem:        29700        27416         2284            0          740
free:  Swap:        96348         5616        90732
free: Total:       126048        33032        93016
/proc/cpuinfo: Processor	: XScale-IXP42x Family rev 1 (v5l)
/proc/cpuinfo: BogoMIPS	: 266.24
/proc/cpuinfo: Features	: swp half fastmult edsp 
/proc/cpuinfo: CPU implementer	: 0x69
/proc/cpuinfo: CPU architecture: 5TE
/proc/cpuinfo: CPU variant	: 0x0
/proc/cpuinfo: CPU part	: 0x41f
/proc/cpuinfo: CPU revision	: 1
/proc/cpuinfo: Cache type	: undefined 5
/proc/cpuinfo: Cache clean	: undefined 5
/proc/cpuinfo: Cache lockdown	: undefined 5
/proc/cpuinfo: Cache format	: Harvard
/proc/cpuinfo: I size		: 32768
/proc/cpuinfo: I assoc		: 32
/proc/cpuinfo: I line length	: 32
/proc/cpuinfo: I sets		: 32
/proc/cpuinfo: D size		: 32768
/proc/cpuinfo: D assoc		: 32
/proc/cpuinfo: D line length	: 32
/proc/cpuinfo: D sets		: 32
/proc/cpuinfo: 
/proc/cpuinfo: Hardware	: Linksys NSLU2
/proc/cpuinfo: Revision	: 0000
/proc/cpuinfo: Serial		: 0000000000000000
/proc/ioports: 00000000-0000ffff : PCI I/O Space
/proc/iomem: 00000000-01ffffff : System RAM
/proc/iomem:   00022000-00294fff : Kernel text
/proc/iomem:   00296000-002cfd57 : Kernel data
/proc/iomem: 48000000-4bffffff : PCI Memory Space
/proc/iomem:   48000000-48000fff : 0000:00:01.0
/proc/iomem:     48000000-48000fff : ohci_hcd
/proc/iomem:   48001000-48001fff : 0000:00:01.1
/proc/iomem:     48001000-48001fff : ohci_hcd
/proc/iomem:   48002000-480020ff : 0000:00:01.2
/proc/iomem:     48002000-480020ff : ehci_hcd
/proc/iomem: 50000000-50ffffff : IXP4XX-Flash.0
/proc/iomem:   50000000-50ffffff : IXP4XXFlash
/proc/iomem: 60000000-60003fff : IXP4xx Queue Manager
/proc/iomem: c8000000-c8000fff : serial8250.0
/proc/iomem:   c8000000-c800001f : serial
/proc/iomem: c8001000-c8001fff : serial8250.0
/proc/iomem:   c8001000-c800101f : serial
/proc/iomem: c8007000-c8007fff : NPE-B
/proc/iomem: c8008000-c8008fff : NPE-C
/proc/iomem: c8009000-c8009fff : eth0
/proc/iomem: c800b000-c800bfff : pxa2xx-udc
/proc/interrupts:            CPU0
/proc/interrupts:   3:      92179      IXP4xx  IXP4xx Queue Manager
/proc/interrupts:   5:     813536      IXP4xx  timer1
/proc/interrupts:  11:       1317      IXP4xx  ixp4xx-beeper
/proc/interrupts:  15:        972      IXP4xx  serial
/proc/interrupts:  22:          0      IXP4xx  NSLU2 power button
/proc/interrupts:  26:    2516983      IXP4xx  ehci_hcd:usb1
/proc/interrupts:  27:          0      IXP4xx  ohci_hcd:usb3
/proc/interrupts:  28:          0      IXP4xx  ohci_hcd:usb2
/proc/interrupts:  29:          0      IXP4xx  NSLU2 reset button
/proc/interrupts: Err:          0
/proc/meminfo: MemTotal:        29700 kB
/proc/meminfo: MemFree:          2264 kB
/proc/meminfo: Buffers:           740 kB
/proc/meminfo: Cached:          17896 kB
/proc/meminfo: SwapCached:       2212 kB
/proc/meminfo: Active:          12256 kB
/proc/meminfo: Inactive:         9140 kB
/proc/meminfo: SwapTotal:       96348 kB
/proc/meminfo: SwapFree:        90732 kB
/proc/meminfo: Dirty:             372 kB
/proc/meminfo: Writeback:           0 kB
/proc/meminfo: AnonPages:        2592 kB
/proc/meminfo: Mapped:           1568 kB
/proc/meminfo: Slab:             3040 kB
/proc/meminfo: SReclaimable:     1264 kB
/proc/meminfo: SUnreclaim:       1776 kB
/proc/meminfo: PageTables:        404 kB
/proc/meminfo: NFS_Unstable:        0 kB
/proc/meminfo: Bounce:              0 kB
/proc/meminfo: CommitLimit:    111196 kB
/proc/meminfo: Committed_AS:    12772 kB
/proc/meminfo: VmallocTotal:   991232 kB
/proc/meminfo: VmallocUsed:     16856 kB
/proc/meminfo: VmallocChunk:   966652 kB
/proc/bus/input/devices: I: Bus=0019 Vendor=001f Product=0001 Version=0100
/proc/bus/input/devices: N: Name="ixp4xx beeper"
/proc/bus/input/devices: P: Phys=ixp4xx/gpio
/proc/bus/input/devices: S: Sysfs=/class/input/input0
/proc/bus/input/devices: U: Uniq=
/proc/bus/input/devices: H: Handlers=kbd event0 
/proc/bus/input/devices: B: EV=40001
/proc/bus/input/devices: B: SND=6
/proc/bus/input/devices: 

==============================================
Installer status:
==============================================
Package: preseed-common
Status: install ok unpacked
Version: 1.35
Depends: cdebconf-udeb, di-utils (>= 1.14)
Description: common files for preseeding

Package: nic-usb-modules-2.6.24-1-ixp4xx-di
Status: install ok unpacked
Version: 1.14
Provides: nic-usb-modules
Depends: core-modules-2.6.24-1-ixp4xx-di, kernel-image-2.6.24-1-ixp4xx-di, usb-modules-2.6.24-1-ixp4xx-di
Description: USB NIC drivers

Package: udpkg
Status: install ok unpacked
Version: 1.06
Depends: libc6 (>= 2.5-5), libdebian-installer4-udeb (>= 0.51)
Description: tiny dpkg clone

Package: kernel-image-2.6.24-1-ixp4xx-di
Status: install ok unpacked
Version: 1.14
Provides: kernel-image, socket-modules
Description: Linux kernel binary image for the Debian installer

Package: oldsys-preseed
Status: install ok unpacked
Version: 1.3
Depends: devio-udeb
Description: Preseed debian-installer from an existing device

Package: libnss-dns-udeb
Status: install ok unpacked
Version: 2.7-10
Description: GNU C Library: NSS helper for DNS - udeb

Package: download-installer
Status: install ok installed
Version: 1.20
Depends: anna (>= 1.07), cdebconf-udeb, net-retriever
Description: Download installer components
Installer-Menu-Item: 2300

Package: lowmemcheck
Status: install ok unpacked
Version: 1.28
Depends: cdebconf-udeb (>= 0.75), main-menu (>= 1.03)
Description: detect low-memory systems and enter lowmem mode

Package: main-menu
Status: install ok unpacked
Version: 1.26
Depends: cdebconf-udeb, libc6 (>= 2.7-1), libdebconfclient0-udeb, libdebian-installer4-udeb (>= 0.57)
Description: Debian installer main menu

Package: di-utils-shell
Status: install ok unpacked
Version: 1.57
Depends: cdebconf-udeb, di-utils (>= 1.18)
Description: Execute a shell
Installer-Menu-Item: 95000

Package: di-utils
Status: install ok installed
Version: 1.57
Depends: libc6 (>= 2.7-1), libdebian-installer4-udeb (>= 0.57), cdebconf-udeb
Description: Miscellaneous utilities for the debian installer

Package: choose-mirror
Status: install ok installed
Version: 2.24
Depends: choose-mirror-bin, configured-network
Description: Choose mirror to install from (menu item)
Installer-Menu-Item: 2300

Package: cdebconf-newt-udeb
Status: install ok unpacked
Version: 0.130
Depends: cdebconf-udeb, di-utils-terminfo, libc6 (>= 2.7-1), libnewt0.52, libslang2-udeb (>= 2.0.7-1)
Description: Newt frontend for Debian Configuration Management System

Package: dhcp3-client-udeb
Status: install ok installed
Version: 3.1.0-5
Depends: libc6 (>= 2.7-1)
Description: DHCP Client for debian-installer

Package: module-init-tools-udeb
Status: install ok unpacked
Version: 3.4-1
Depends: libc6 (>= 2.7-1)
Description: tools for managing Linux kernel modules

Package: gpgv-udeb
Status: install ok installed
Version: 1.4.6-2.1
Depends: libc6 (>= 2.7-1), zlib1g-udeb (>= 1:1.2.3.3.dfsg-1)
Description: minimal signature verification tool

Package: rootskel
Status: install ok installed
Version: 1.62
Depends: cdebconf-udeb, di-utils (>= 1.43)
Description: Skeleton root filesystem used by debian-installer

Package: input-modules-2.6.24-1-ixp4xx-di
Status: install ok unpacked
Version: 1.14
Provides: input-modules
Depends: kernel-image-2.6.24-1-ixp4xx-di, usb-modules-2.6.24-1-ixp4xx-di
Description: Input devices support

Package: openssh-server-udeb
Status: install ok installed
Version: 1:4.7p1-8
Depends: libc6 (>= 2.7-1), libcrypto0.9.8-udeb (>= 0.9.8f-5), libgcc1 (>= 1:4.3), libnss-files-udeb, zlib1g-udeb (>= 1:1.2.3.3.dfsg-1)
Description: secure shell server for the Debian installer

Package: network-console
Status: install ok unpacked
Version: 1.15
Depends: cdebconf-udeb, configured-network, openssh-server-udeb (>= 1:3.8p1-1)
Description: Continue installation remotely using SSH
Installer-Menu-Item: 2100

Package: udev-udeb
Status: install ok unpacked
Version: 0.114-2
Depends: libc6 (>= 2.6-1)
Description: /dev/ and hotplug management daemon

Package: libnss-files-udeb
Status: install ok installed
Version: 2.7-10
Description: GNU C Library: NSS helper for files - udeb

Package: libcrypto0.9.8-udeb
Status: install ok installed
Version: 0.9.8g-8
Depends: libc6 (>= 2.7-1), libgcc1 (>= 1:4.3), zlib1g-udeb (>= 1:1.2.3.3.dfsg-1)
Description: crypto shared library - udeb

Package: libfribidi0-udeb
Status: install ok unpacked
Version: 0.10.9-1
Depends: libc6 (>= 2.7-1)
Description: Free Implementation of the Unicode BiDi algorithm

Package: libtextwrap1-udeb
Status: install ok installed
Version: 0.1-6
Depends: libc6 (>= 2.7-1)
Description: text-wrapping library with i18n - runtime udeb

Package: auto-install
Status: install ok unpacked
Version: 1.2
Depends: cdebconf-udeb, netcfg, preseed-common (>= 1.18)
Description: Support for automatic installs
Installer-Menu-Item: 1900

Package: rescue-check
Status: install ok unpacked
Version: 1.14
Depends: cdebconf-udeb (>= 0.75), main-menu (>= 1.03), di-utils (>= 1.18)
Description: enter d-i rescue mode if requested

Package: nano-udeb
Status: install ok unpacked
Version: 2.0.7-1
Provides: editor
Depends: libc6 (>= 2.7-1), libslang2-udeb (>= 2.0.7-1)
Description: free Pico clone with some new features - tiny build

Package: debian-archive-keyring-udeb
Status: install ok installed
Version: 2008.04.16+nmu1
Description: GnuPG keys of the Debian archive

Package: nic-modules-2.6.24-1-ixp4xx-di
Status: install ok unpacked
Version: 1.14
Provides: nic-modules
Depends: core-modules-2.6.24-1-ixp4xx-di, kernel-image-2.6.24-1-ixp4xx-di
Description: Common NIC drivers

Package: ai-choosers
Status: install ok unpacked
Version: 1.2
Depends: keyboard-setup, localechooser (>= 1.23)
Description: Delayed configuration of locale and keyboard for auto-install
Installer-Menu-Item: 2200

Package: cdebconf-text-udeb
Status: install ok unpacked
Version: 0.130
Depends: cdebconf-udeb, libc6 (>= 2.7-1)
Description: Plain text frontend for Debian Configuration Management System

Package: iso-3166-udeb
Status: install ok installed
Version: 2.0-1
Description: provides iso_3166.tab file

Package: core-modules-2.6.24-1-ixp4xx-di
Status: install ok unpacked
Version: 1.14
Provides: core-modules
Depends: kernel-image-2.6.24-1-ixp4xx-di
Description: Core modules

Package: ethdetect
Status: install ok installed
Version: 1.61
Provides: ethernet-card-detection
Depends: cdebconf-udeb (>= 0.38), di-utils (>= 1.13), hw-detect, rootskel (>= 1.30)
Description: Detect network hardware and load kernel drivers for it
Installer-Menu-Item: 1700

Package: devio-udeb
Status: install ok unpacked
Version: 1.2-1
Depends: libc6 (>= 2.5)
Description: correctly read (or write) a region of a block device

Package: busybox-udeb
Status: install ok unpacked
Version: 1:1.9.2-3
Depends: libc6 (>= 2.7-1), libgcc1 (>= 1:4.3)
Description: Tiny utilities for the debian-installer

Package: initrd-preseed
Status: install ok unpacked
Version: 1.35
Depends: preseed-common
Description: load debconf preseed file from /preseed.cfg on the initrd

Package: net-retriever
Status: install ok installed
Version: 1.20
Provides: retriever
Depends: cdebconf-udeb, choose-mirror, configured-network, debian-archive-keyring-udeb, di-utils (>= 1.16), gpgv-udeb
Description: Fetch modules from the Internet

Package: usb-modules-2.6.24-1-ixp4xx-di
Status: install ok unpacked
Version: 1.14
Provides: usb-modules
Depends: kernel-image-2.6.24-1-ixp4xx-di
Description: USB support

Package: libiw29-udeb
Status: install ok installed
Version: 29-1
Depends: libc6 (>= 2.6.1-1)
Description: Tools for manipulating Linux Wireless Extensions

Package: beep-udeb
Status: install ok unpacked
Version: 1.2.2-20
Depends: libc6 (>= 2.6.1-1)
Description: advanced pc-speaker beeper

Package: di-utils-reboot
Status: install ok unpacked
Version: 1.57
Depends: cdebconf-udeb
Description: Reboot
Installer-Menu-Item: 99500

Package: choose-mirror-bin
Status: install ok installed
Version: 2.24
Depends: cdebconf-udeb, libc6 (>= 2.7-1), libdebconfclient0-udeb, libdebian-installer4-udeb (>= 0.57)
Description: Choose mirror to install from (program)

Package: pciutils-udeb
Status: install ok unpacked
Version: 1:3.0.0-3
Depends: libc6 (>= 2.7-1), zlib1g-udeb (>= 1:1.2.3.3.dfsg-1)
Description: Linux PCI Utilities (udeb)

Package: console-keymaps-at
Status: install ok installed
Version: 2:1.07-2
Provides: console-keymaps
Depends: cdebconf-udeb
Description: keymaps for PC-style (PS/2 and AT) keyboards

Package: di-utils-terminfo
Status: install ok unpacked
Version: 1.57
Description: Terminfo entries needed by newt/slang in debian installer

Package: kbd-chooser
Status: install ok installed
Version: 1.43
Provides: keyboard-setup
Depends: cdebconf-udeb, console-keymaps, libc6 (>= 2.7-1), libdebconfclient0-udeb, libdebian-installer4-udeb (>= 0.55)
Description: Detect a keyboard and select layout
Installer-Menu-Item: 1200

Package: installation-locale
Status: install ok unpacked
Version: 1.2
Depends: rootskel
Description: UTF-8 C locale

Package: env-preseed
Status: install ok unpacked
Version: 1.35
Description: debconf preseeding via environment variables

Package: netcfg
Status: install ok installed
Version: 1.43
Provides: configured-network
Depends: dhcp3-client-udeb (>= 3.1.0-2), ethernet-card-detection, libc6 (>= 2.7-1), libdebconfclient0-udeb, libdebian-installer4-udeb (>= 0.57), libiw29-udeb (>= 28+29pre7)
Description: Configure the network
Installer-Menu-Item: 1800

Package: zlib1g-udeb
Status: install ok installed
Version: 1:1.2.3.3.dfsg-12
Description: compression library - runtime for Debian installer

Package: bogl-bterm-udeb
Status: install ok unpacked
Version: 0.1.18-2
Provides: editor
Depends: libc-udeb
Description: Ben's Own Graphics Library - graphical terminal

Package: debian-installer
Status: install ok installed
Version: ixp4xx-netboot-20080513-09:33
Description: debian installation image

Package: apt-mirror-setup
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 176
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1:0.37
Depends: choose-mirror-bin, cdebconf-udeb
Description: set up a mirror in sources.list

Package: apt-setup-udeb
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 160
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1:0.37
Depends: apt-mirror-setup, installed-base, cdebconf-udeb
Description: Configure apt
Installer-Menu-Item: 7000

Package: base-installer
Status: install ok installed
Priority: required
Section: debian-installer
Installed-Size: 156
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.91
Depends: cdebconf-udeb, di-utils-mapdevfs, di-utils (>= 1.48), rootskel (>= 1.19)
Description: base system installation framework

Package: bootstrap-base
Status: install ok installed
Priority: required
Section: debian-installer
Installed-Size: 524
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.91
Depends: libc6 (>= 2.7-1), libdebconfclient0-udeb, libdebian-installer4-udeb (>= 0.57), mounted-partitions, created-fstab, base-installer, debootstrap-udeb (>= 1.0.7), gpgv-udeb, debian-archive-keyring-udeb, archdetect
Provides: installed-base, kernel-installer
Description: Install the base system
Installer-Menu-Item: 6500

Package: cdebconf-priority
Status: install ok unpacked
Priority: standard
Section: debian-installer
Installed-Size: 16
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 0.131
Depends: cdebconf-udeb
Description: Change debconf priority
 This is a udeb that allows you to change the priority limit for the
 questions.
Installer-Menu-Item: 93000

Package: clock-setup
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 140
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 0.95
Depends: cdebconf-udeb, configured-network, di-utils, localechooser, rdate-udeb (>= 1:1.1.2-5), tzsetup-udeb (>= 1:0.18)
Description: set up clock
Installer-Menu-Item: 2600

Package: debootstrap-udeb
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 96
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.0.9
Depends: mounted-partitions
Description: Bootstrap the Debian system

Package: di-utils-mapdevfs
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 16
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.57
Depends: libc6 (>= 2.7-1), libdebian-installer4-udeb (>= 0.57)
Description: mapdevfs utility for the debian installer

Package: disk-detect
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 72
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.62
Depends: cdebconf-udeb (>= 0.38), hw-detect, di-utils (>= 1.13)
Provides: harddrive-detection
Description: Detect disk drives
Installer-Menu-Item: 3500

Package: e2fsprogs-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 460
Maintainer: Theodore Y. Ts'o <tytso@mit.edu>
Version: 1.40.8-2
Depends: libblkid1-udeb, libc6 (>= 2.7-1), libgcc1 (>= 1:4.3)
Description: stripped-down versions of e2fsprogs, for debian-installer
 This package is an e2fsprogs package built for a reduced size, so that
 it can help to save space in debian-installer.
 .
 Don't attempt to install this package, it has no support for a couple of
 features you surely want.  Anyway it should refuse to install.

Package: ext2-modules-2.6.24-1-ixp4xx-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 120
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.14
Depends: core-modules-2.6.24-1-ixp4xx-di, kernel-image-2.6.24-1-ixp4xx-di
Provides: ext2-modules
Description: EXT2 filesystem support
 This package contains the EXT2 filesystem module for the Linux kernel.

Package: ext3-modules-2.6.24-1-ixp4xx-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 260
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.14
Depends: core-modules-2.6.24-1-ixp4xx-di, kernel-image-2.6.24-1-ixp4xx-di
Provides: ext3-modules
Description: EXT3 filesystem support
 This package contains the EXT3 filesystem module for the Linux kernel.

Package: fat-modules-2.6.24-1-ixp4xx-di
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 140
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.14
Depends: kernel-image-2.6.24-1-ixp4xx-di
Provides: fat-modules
Description: FAT filesystem support
 This package contains the FAT and VFAT filesystem modules for the Linux kernel.

Package: finish-install
Status: install ok unpacked
Priority: required
Section: debian-installer
Installed-Size: 116
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 2.18
Depends: cdebconf-udeb, archdetect, installed-base, created-fstab, bootable-system
Description: Finish the installation and reboot
Installer-Menu-Item: 7800

Package: flash-kernel-installer
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 36
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.11
Depends: cdebconf-udeb, installed-base
Provides: bootable-system
Description: Configure flash to boot the system
Installer-Menu-Item: 7300

Package: libblkid1-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 48
Maintainer: Theodore Y. Ts'o <tytso@mit.edu>
Version: 1.40.8-2
Depends: libc6 (>= 2.7-1), libgcc1 (>= 1:4.3)
Description: block device id library
 The blkid library which allows system programs like fsck and
 mount to quickly and easily find block devices by filesystem UUID and
 LABEL.  This allows system administrators to avoid specifiying
 filesystems by hard-coded device names, but via a logical naming
 system instead.
 .
 This is a minimal package for debian-installer.

Package: libc6-udeb
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 2188
Maintainer: GNU Libc Maintainers <debian-glibc@lists.debian.org>
Version: 2.7-10
Provides: glibc-2.7-1, libc-udeb, libc6
Description: GNU C Library: Shared libraries - udeb
 Contains the standard libraries that are used by nearly all programs on
 the system. This package includes shared versions of the standard C library
 and the standard math library, as well as many others.
 .
 This package contains a minimal set of libraries needed for the Debian
 installer.  Do not install it on a normal system.

Package: libparted1.7-udeb
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 372
Maintainer: Parted Maintainer Team <parted-maintainers@lists.alioth.debian.org>
Version: 1.7.1-5.1
Depends: libc6 (>= 2.5), libgcc1 (>= 1:4.1.1-12), libuuid1-udeb
Provides: libparted1.7-1
Description: The GNU Parted disk partitioning shared library
 GNU Parted is a program that allows you to create, destroy,
 resize, move and copy hard disk partitions. This is useful
 for creating space for new operating systems, reorganising
 disk usage, and copying data to new hard disks. This package
 contains the Parted binary and manual page.
 .
 This package contains libparted, the required shared library
 used by Parted. This is a cut-down package with no normal
 documentation intended to be used in debian-installer.
 .
 Parted currently supports DOS, Mac, Sun, BSD, GPT, MIPS and
 PC98 disklabels/partition tables, as well as a 'loop' (raw
 disk) type which allows use on RAID/LVM. Filesystems which
 are currently fully supported are ext2, ext3, fat (FAT16
 and FAT32), ReiserFS (with libreiserfs) and linux-swap.
 Parted can also detect and remove HFS (Mac OS), JFS, NTFS,
 UFS (Sun and HP), XFS and ASFS/AFFS/APFS (Amiga) filesystems,
 but cannot create, resize or check these filesystems yet.
 .
 Note that ReiserFS support is only enabled if you install
 the libreiserfs0.3-0 package. Since libreiserfs0.3-0 has been
 removed from sarge, ReiserFS support is not compiled in the
 default package.
 .
 The nature of this software means that any bugs could cause
 massive data loss. While there are no known bugs at the moment,
 they could exist, so please back up all important files before
 running it, and do so at your own risk.

Package: libuuid1-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 28
Maintainer: Theodore Y. Ts'o <tytso@mit.edu>
Version: 1.40.8-2
Depends: libc6 (>= 2.7-1), libgcc1 (>= 1:4.3)
Description: universally unique id library
 libuuid generates and parses 128-bit universally unique id's (UUID's).
 See RFC 4122 for more information.
 .
 This is a minimal package for debian-installer.

Package: localechooser
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 672
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 2.03
Depends: cdebconf-udeb (>= 0.129), iso-3166-udeb
Description: choose language/country/locale
Installer-Menu-Item: 1000

Package: lowmem
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 32
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.29
Description: free memory for lowmem install
Installer-Menu-Item: 2500

Package: network-preseed
Status: install ok unpacked
Priority: standard
Section: debian-installer
Installed-Size: 40
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.36
Depends: cdebconf-udeb, configured-network, preseed-common
Description: download debconf preseed file
Installer-Menu-Item: 2100

Package: nobootloader
Status: install ok unpacked
Priority: standard
Section: debian-installer
Installed-Size: 228
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.21
Depends: cdebconf-udeb, installed-base, di-utils-mapdevfs
Provides: bootable-system
Description: Don't install any bootloader.
 This package will skip installing a boot-loader
Installer-Menu-Item: 7700

Package: partman-auto
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 384
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 78
Depends: cdebconf-udeb, di-utils, partman-base (>= 114), partman-basicfilesystems, partman-ext3
Description: Automatically partition storage devices (partman)

Package: partman-base
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 808
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 119
Depends: libc6 (>= 2.7-1), libgcc1 (>= 1:4.3), libparted1.7-udeb (>= 1.7.1-1), cdebconf-udeb, partman-utils, partman-partitioning (>= 54), partman-target, archdetect, harddrive-detection, di-utils-mapdevfs, di-utils (>= 1.15)
Provides: created-fstab, made-filesystems, mounted-partitions, partitioned-harddrives
Description: Partition the storage devices (partman)
Installer-Menu-Item: 4200

Package: partman-basicfilesystems
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 628
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 60
Depends: cdebconf-udeb, e2fsprogs-udeb, ext2-modules, fat-modules
Provides: partman-filesystem
Description: Add to partman support for ext2, linux-swap, fat16 and fat32

Package: partman-basicmethods
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 132
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 39
Depends: cdebconf-udeb
Provides: partman-method
Description: Basic partition usage methods for partman
 This package provides partman with two methods to use partitions.
 The first is to format the partition.  The second is to keep and use
 the existing data in the partition as it is.

Package: partman-ext3
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 188
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 52
Depends: cdebconf-udeb, e2fsprogs-udeb, ext3-modules, partman-basicfilesystems (>= 59)
Provides: partman-filesystem
Description: Add to partman support for ext3

Package: partman-partitioning
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 556
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 59
Depends: e2fsprogs-udeb, cdebconf-udeb
Description: Partitioning operations for partman
 This udeb provides partman with editing operations for creation
 of new partitions, deletion of partitions and initialisation of the
 partition table.

Package: partman-target
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 352
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 55
Depends: cdebconf-udeb, partman-basicfilesystems, partman-basicmethods, di-utils-mapdevfs
Description: Provides partman with ability to prepare /target
 This udeb allows the user to choose how partitions should be used.

Package: partman-utils
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 20
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 119
Depends: libc6 (>= 2.7-1), libparted1.7-udeb (>= 1.7.1-1)
Description: Utilities related to partitioning

Package: pkgsel
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 56
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 0.20
Depends: cdebconf-udeb, apt-setup-udeb, di-utils (>= 1.56)
Description: Select and install packages
Installer-Menu-Item: 7000

Package: rdate-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 32
Maintainer: Anibal Monsalve Salazar <anibal@debian.org>
Version: 1:1.1.3-1
Depends: libc6 (>= 2.7-1)
Description: sets the system's date from a remote host

Package: save-logs
Status: install ok unpacked
Priority: standard
Section: debian-installer
Installed-Size: 196
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 2.35
Depends: cdebconf-udeb
Description: save logs and configuration for debug purposes
Installer-Menu-Item: 94000

Package: scsi-core-modules-2.6.24-1-ixp4xx-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 212
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.14
Depends: kernel-image-2.6.24-1-ixp4xx-di
Provides: scsi-core-modules
Description: Core SCSI subsystem
 This package contains the core SCSI subsystem for the Linux kernel.

Package: tzsetup-udeb
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 308
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1:0.21
Depends: cdebconf-udeb, localechooser
Description: choose time zone

Package: usb-storage-modules-2.6.24-1-ixp4xx-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 148
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.14
Depends: kernel-image-2.6.24-1-ixp4xx-di, scsi-core-modules-2.6.24-1-ixp4xx-di, usb-modules-2.6.24-1-ixp4xx-di
Provides: usb-storage-modules
Description: USB storage support
 This package contains the USB storage driver for the Linux kernel.

Package: user-setup-udeb
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 372
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.20
Depends: cdebconf-udeb
Description: Set up users and passwords
Installer-Menu-Item: 6900

Package: archdetect
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 16
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.62
Depends: libc6 (>= 2.7-1), libdebian-installer4-udeb (>= 0.57)
Description: Hardware architecture detector

Package: cdebconf-udeb
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 260
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 0.131
Depends: libc6 (>= 2.7-1), libdebian-installer4-udeb (>= 0.58), libtextwrap1-udeb
Provides: debconf-2.0
Description: Debian Configuration Management System (C-implementation)
 Debconf is a configuration management system for Debian packages. It is
 used by some packages to prompt you for information before they are
 installed. This is a reimplementation of the original debconf version
 in C.
 .
 cdebconf-udeb is a minimal cdebconf package used by the
 debian-installer

Package: hw-detect
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 252
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.62
Depends: rootskel (>= 1.30), archdetect, cdebconf-udeb (>= 0.75), di-utils (>= 1.48)
Description: Detect hardware and load kernel drivers for it

Package: libdebian-installer4-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 52
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 0.58
Depends: libc6 (>= 2.7-1)
Description: Library of common debian-installer functions
 This library is used by debian-installer to perform common functions
 such as logging messages and executing commands. If you aren't
 working on debian-installer or building your own install system based
 on debian-installer, then you probably don't need this library.

Package: libdevmapper1.02.1-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 96
Maintainer: Debian LVM Team <pkg-lvm-maintainers@lists.alioth.debian.org>
Version: 2:1.02.24-4
Depends: libc6 (>= 2.7-1)
Description: The Linux Kernel Device Mapper userspace library
 This is a udeb, or a microdeb, for the debian-installer.
 .
 The Linux Kernel Device Mapper is the LVM (Linux Logical Volume Management)
 Team's implementation of a minimalistic kernel-space driver that handles
 volume management, while keeping knowledge of the underlying device layout
 in user-space.  This makes it useful for not only LVM, but EVMS, software
 raid, and other drivers that create "virtual" block devices.

Package: lvm2-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 536
Maintainer: Debian LVM Team <pkg-lvm-maintainers@lists.alioth.debian.org>
Version: 2.02.35-1
Depends: libc6 (>= 2.7-1), libdevmapper1.02.1-udeb (>= 2:1.02.24), libgcc1 (>= 1:4.3)
Description: The Linux Logical Volume Manager
 This is a udeb, or a microdeb, for the debian-installer.
 .
 This is LVM2, the rewrite of The Linux Logical Volume Manager.  LVM
 supports enterprise level volume management of disk and disk subsystems
 by grouping arbitrary disks into volume groups. The total capacity of
 volume groups can be allocated to logical volumes, which are accessed as
 regular block devices.

Package: md-modules-2.6.24-1-ixp4xx-di
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 520
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.14
Depends: kernel-image-2.6.24-1-ixp4xx-di
Provides: md-modules
Description: RAID and LVM support
 This package contains RAID and LVM modules for the Linux kernel.

Package: partman-auto-lvm
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 172
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 27
Depends: cdebconf-udeb, partman-base (>= 114), partman-auto (>= 74), partman-lvm (>= 58), di-utils (>= 1.15)
Description: Automatically partition storage devices using LVM

Package: partman-lvm
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 800
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 61
Depends: cdebconf-udeb, partman-base (>= 114), di-utils (>= 1.14), md-modules, lvm2-udeb
Description: Adds support for LVM to partman

Package: anna
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 184
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.32
Depends: libc6 (>= 2.7-1), libdebconfclient0-udeb, libdebian-installer4-udeb (>= 0.57), cdebconf-udeb
Description: anna's not nearly apt, but for the Debian installer, it will do

Package: libdebconfclient0-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 24
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 0.131
Depends: libc6 (>= 2.7-1), cdebconf-udeb
Description: Debian Configuration Management System (C-implementation)
 Debconf is a configuration management system for Debian packages. It is
 used by some packages to prompt you for information before they are
 installed. This is a reimplementation of the original debconf version
 in C.
 .
 This is a udeb version of libdebconfclient0.

Package: os-prober-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 104
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.25
Depends: di-utils-mapdevfs, anna (>= 1.16)
Provides: os-prober
Description: utility to detect other OSes on a set of drives
 This package is to be used by boot loader installers to detect other OSes
 available on a system, in a generic format, which it can then adapt to its
 own configuration format.

Package: reiserfs-modules-2.6.24-1-ixp4xx-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 316
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.14
Depends: kernel-image-2.6.24-1-ixp4xx-di
Provides: reiserfs-modules
Description: Reiser filesystem support
 This package contains the Reiser filesystem module for the Linux kernel.


-- System Information:
Debian Release: lenny/sid
  APT prefers testing
  APT policy: (500, 'testing')
Architecture: armel (armv5tel)

Kernel: Linux 2.6.24-1-ixp4xx
Locale: LANG=C, LC_CTYPE=C (charmap=ANSI_X3.4-1968)
Shell: /bin/sh linked to /bin/dash

installation-report depends on no packages.

Versions of packages installation-report recommends:
ii  pciutils                      1:3.0.0-4  Linux PCI Utilities
ii  reportbug                     3.39-0.1   reports bugs in the Debian distrib

-- no debconf information



Reply to: