Bug#469208: bug report pci don't works
Package: installation-reports
Boot method: <How did you boot the installer? CD? floppy? network?> cd
Image version: <Full URL to image you downloaded is best>
Date: <Date and time of the install>25.03.2008
Machine: <Description of machine (eg, IBM Thinkpad R32)>toshiba portege7200
Processor:p-3
Memory:328 mb
Partitions: <df -Tl will do; the raw partition table is preferred>T7200:/home/lm# df -Tl
Filesystem Type 1K-blocks Used Available Use% Mounted on
/dev/hda3 ext3 5052060 2461544 2333880 52% /
tmpfs tmpfs 160864 0 160864 0% /lib/init/rw
udev tmpfs 10240 80 10160 1% /dev
tmpfs tmpfs 160864 0 160864 0% /dev/shm
T7200:/home/lm#
Output of lspci -nn and lspci -vnn:at the below letter
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot: [o]
Detect network card: [ o]
Configure network: [o ] see below - was problems.
Detect CD: [o ]
Load installer modules: [o ]
Detect hard drives: [o ]
Partition hard drives: [o ]
Install base system: [o ]
Clock/timezone setup: [o ]
User/password setup: [ o]
Install tasks: [ o]
Install boot loader: [ o]
Overall install: [ o]
Comments/Problems:
all applicaions work OK, just some pci devices dont installed
1/wi-wi eternet card (10-100 installs ok and works)
2/Irda
3/Usb - don't sees Usb PDA cradle
4/PCMCIA - doesn't see nor flash cards, nor wi-fi card, nor GPS.
5. synce doesn't work, I install it but possible it because of item 3?
6/screen resolution don't change, in spite of I change line in xorg.conf.
all these devices are properly configured (see in LCPCI reply below)
<Description of the install, in prose, and any thoughts, comments
and ideas you had during the initial install.>
In the bug report, describe what the problem is, including the last
visible kernel messages in the event of a kernel hang. Describe the
steps that you did which brought the system into the problem state.
dmesg
Linux version 2.6.18-6-686 (Debian 2.6.18.dfsg.1-18etch1)
(waldi@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian
4.1.1-21)) #1 SMP Sun Feb 10 22:11:31 UTC 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 00000000000e8640 (reserved)
BIOS-e820: 00000000000e8640 - 00000000000e8840 (ACPI NVS)
BIOS-e820: 00000000000e8840 - 00000000000ec000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000013fe0000 (usable)
BIOS-e820: 0000000013fe0000 - 0000000013ff0000 (ACPI data)
BIOS-e820: 0000000013ff0000 - 0000000014000000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
319MB LOWMEM available.
On node 0 totalpages: 81888
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 77792 pages, LIFO batch:15
DMI 2.3 present.
ACPI: RSDP (v000 TOSHIB ) @ 0x000f0170
ACPI: RSDT (v001 TOSHIB 750 0x00970814 TASM 0x04010000) @
0x13fe0000
ACPI: FADT (v001 TOSHIB 750 0x00970814 TASM 0x04010000) @
0x13fe0054
ACPI: DSDT (v001 TOSHIB 7100 0x20000621 MSFT 0x0100000a) @
0x00000000
ACPI: PM-Timer IO Port: 0xfe08
Allocating PCI resources starting at 20000000 (gap: 14000000:ebf80000)
Detected 646.874 MHz processor.
Built 1 zonelists. Total pages: 81888
Kernel command line: root=/dev/hda3 ro
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (0128a000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 316596k/327552k available (1541k kernel code, 10424k reserved,
580k data, 196k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode...
Ok.
Calibrating delay using timer specific routine.. 1294.77 BogoMIPS
(lpj=2589557)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0387f9ff 00000000 00000000 00000000
00000000 00000000 00000000
CPU: After vendor identify, caps: 0387f9ff 00000000 00000000 00000000
00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU serial number disabled.
CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
ACPI: Core revision 20060707
ACPI: setting ELCR to 0200 (from 0808)
CPU0: Intel Pentium III (Coppermine) stepping 03
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
migration_cost=0
checking if image is initramfs... it is
Freeing initrd memory: 4781k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfed9b, last bus=21
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKE] (IRQs *3 4)
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
PCI quirk: region fe00-fe3f claimed by PIIX4 ACPI
PCI quirk: region fe70-fe7f claimed by PIIX4 SMB
PIIX4 devres B PIO at 006c-006f
PCI: Firmware left 0000:00:06.0 e100 interrupts enabled, disabling
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Power Resource [PIHD] (on)
ACPI: Power Resource [PMHD] (off)
ACPI: Power Resource [PDOC] (off)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: Power Resource [PFAN] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
PCI: setting IRQ 13 as level-triggered
pnp: PnP ACPI: found 12 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
report
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: f0000000-f7ffffff
PREFETCH window: 28000000-280fffff
PCI: Bus 2, cardbus bridge: 0000:00:0b.0
IO window: 00001000-000010ff
IO window: 00001400-000014ff
PREFETCH window: 20000000-21ffffff
MEM window: 22000000-23ffffff
PCI: Bus 6, cardbus bridge: 0000:00:0b.1
IO window: 00001800-000018ff
IO window: 00002000-000020ff
PREFETCH window: 24000000-25ffffff
MEM window: 26000000-27ffffff
PCI: Enabling device 0000:00:0b.0 (0000 -> 0003)
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKA] -> GSI 11 (level,
low) -> IRQ 11
PCI: Enabling device 0000:00:0b.1 (0000 -> 0003)
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [LNKB] -> GSI 11 (level,
low) -> IRQ 11
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1204573201.108:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Limiting direct PCI/PCI transfers.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI No-Shortcut mode
ACPI: (supports S0 S1 S3 S4 S5)
Time: tsc clocksource has been installed.
Freeing unused kernel memory: 196k freed
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI: Transitioning device [FAN] to D3
ACPI: Transitioning device [FAN] to D3
ACPI: Fan [FAN] (off)
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Thermal Zone [THRM] (50 C)
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:05.2[D] -> Link [LNKD] -> GSI 11 (level,
low) -> IRQ 11
uhci_hcd 0000:00:05.2: UHCI Host Controller
uhci_hcd 0000:00:05.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:05.2: irq 11, io base 0x0000ff80
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LNKC] -> GSI 11 (level,
low) -> IRQ 11
e100: eth0: e100_probe: addr 0xcffff000, irq 11, MAC addr
00:00:39:50:6D:10
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
PIIX4: IDE controller at PCI slot 0000:00:05.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfff0-0xfff7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfff8-0xffff, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
usb 1-2: new full speed USB device using uhci_hcd and address 2
usb 1-2: configuration #1 chosen from 1 choice
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 4 ports detected
hda: TOSHIBA MK1214GAP, ATA DISK drive
Time: acpi_pm clocksource has been installed.
usb 1-2.4: new low speed USB device using uhci_hcd and address 3
usb 1-2.4: configuration #1 chosen from 1 choice
usbcore: registered new driver hiddev
input: MOSART Semi. Wireless Keyboard & Mouse as /class/input/input1
input: USB HID v1.10 Keyboard [MOSART Semi. Wireless Keyboard & Mouse]
on usb-0000:00:05.2-2.4
input: MOSART Semi. Wireless Keyboard & Mouse as /class/input/input2
input,hiddev96: USB HID v1.10 Mouse [MOSART Semi. Wireless Keyboard &
Mouse] on usb-0000:00:05.2-2.4
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: TOSHIBA DVD-ROM SD-C2102, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 23579136 sectors (12072 MB), CHS=23392/16/63, UDMA(33)
hda: cache flushes not supported
hda: hda1 hda2 < hda5 hda6 hda7 > hda3
hdc: ATAPI 20X DVD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
ts: Compaq touchscreen protocol output
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 440BX Chipset.
agpgart: AGP aperture is 256M @ 0xd0000000
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
piix4_smbus 0000:00:05.3: Found 0000:00:05.3 device
input: PC Speaker as /class/input/input3
Yenta: CardBus bridge found at 0000:00:0b.0 [1179:0001]
irda_init()
NET: Registered protocol family 23
Yenta: ISA IRQ mask 0x04b8, PCI irq 11
Socket status: 30000007
Yenta: CardBus bridge found at 0000:00:0b.1 [1179:0001]
Yenta: ISA IRQ mask 0x04b8, PCI irq 11
Socket status: 30000020
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKC] -> GSI 11 (level,
low) -> IRQ 11
IrDA: Registered device irda0
toshoboe: Using multiple tasks, version $Id: donauboe.c V2.18 ven jan 10
03:14:16 2003$
spurious 8259A interrupt: IRQ7.
logips2pp: Detected unknown logitech mouse model 0
Real Time Clock Driver v1.12ac
pccard: CardBus card inserted into slot 1
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,ECP,DMA]
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
input: ImPS/2 Logitech Wheel Mouse as /class/input/input4
ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKD] -> GSI 11 (level,
low) -> IRQ 11
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
es1968: clocking to 48000
Linux video capture interface: v2.00
Adding 289128k swap on /dev/hda7. Priority:-1 extents:1 across:289128k
EXT3 FS on hda3, internal journal
loop: loaded (max 8 devices)
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised:
dm-devel@redhat.com
pcmcia: Detected deprecated PCMCIA ioctl usage from process: discover.
pcmcia: This interface will soon be removed from the kernel; please
expect breakage unless you upgrade to new tools.
pcmcia: see
http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for
details.
cs: memory probe 0xa0000000-0xa0ffffff: excluding 0xa0000000-0xa0ffffff
cs: memory probe 0x60000000-0x60ffffff: excluding 0x60000000-0x60ffffff
cs: warning: no high memory space available!
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ACPI: Battery Slot [BAT1] (battery absent)
ACPI: AC Adapter [ADP1] (on-line)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKC] -> GSI 11 (level,
low) -> IRQ 11
[drm] Initialized savage 2.4.1 20050313 on minor 0
mtrr: base(0xf2000000) is not aligned on a size(0x5000000) boundary
agpgart: Found an AGP 1.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
eth0: no IPv6 routers present
mtrr: base(0xf2000000) is not aligned on a size(0x5000000) boundary
mtrr: base(0xf2000000) is not aligned on a size(0x5000000) boundary
mtrr: base(0xf2000000) is not aligned on a size(0x5000000) boundary
agpgart: Found an AGP 1.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
lspci -vnn
00:00.0 Host bridge [0600]: Intel Corporation 440BX/ZX/DX -
82443BX/ZX/DX Host bridge [8086:7190] (rev 03)
Subsystem: Toshiba America Info Systems Toshiba Tecra 8100
Laptop System Chipset [1179:0001]
Flags: bus master, medium devsel, latency 64
Memory at d0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [a0] AGP version 1.0
00:01.0 PCI bridge [0604]: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX
AGP bridge [8086:7191] (rev 03) (prog-if 00 [Normal decode])
Flags: bus master, 66MHz, medium devsel, latency 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
Memory behind bridge: f0000000-f7ffffff
Prefetchable memory behind bridge: 28000000-280fffff
00:05.0 Bridge [0680]: Intel Corporation 82371AB/EB/MB PIIX4 ISA
[8086:7110] (rev 02)
Flags: bus master, medium devsel, latency 0
00:05.1 IDE interface [0101]: Intel Corporation 82371AB/EB/MB PIIX4 IDE
[8086:7111] (rev 01) (prog-if 80 [Master])
Flags: bus master, medium devsel, latency 64
I/O ports at fff0 [size=16]
00:05.2 USB Controller [0c03]: Intel Corporation 82371AB/EB/MB PIIX4 USB
[8086:7112] (rev 01) (prog-if 00 [UHCI])
Flags: bus master, medium devsel, latency 64, IRQ 11
I/O ports at ff80 [size=32]
00:05.3 Bridge [0680]: Intel Corporation 82371AB/EB/MB PIIX4 ACPI
[8086:7113] (rev 03)
Flags: medium devsel, IRQ 9
00:06.0 Ethernet controller [0200]: Intel Corporation 82557/8/9
[Ethernet Pro 100] [8086:1229] (rev 05)
Subsystem: Toshiba America Info Systems PCI FastEther LAN on
Docker [1179:0002]
Flags: bus master, medium devsel, latency 64, IRQ 11
Memory at cffff000 (32-bit, prefetchable) [size=4K]
I/O ports at ff60 [size=32]
Memory at eff00000 (32-bit, non-prefetchable) [size=1M]
Expansion ROM at efe00000 [disabled] [size=1M]
Capabilities: [dc] Power Management version 1
00:07.0 Communication controller [0780]: Agere Systems 56k WinModem
[11c1:0441] (rev 01)
Subsystem: Toshiba America Info Systems Internal V.90 Modem
[1179:0001]
Flags: bus master, medium devsel, latency 0, IRQ 3
Memory at ffefff00 (32-bit, non-prefetchable) [size=256]
I/O ports at 02f8 [size=8]
I/O ports at 1c00 [size=256]
Capabilities: [f8] Power Management version 2
00:09.0 IRDA controller [0d00]: Toshiba America Info Systems FIR Port
Type-DO [1179:0d01]
Subsystem: Toshiba America Info Systems FIR Port Type-DO
[1179:0001]
Flags: bus master, slow devsel, latency 64, IRQ 11
I/O ports at ff40 [size=32]
Capabilities: [80] Power Management version 2
00:0b.0 CardBus bridge [0607]: Toshiba America Info Systems ToPIC100 PCI
to Cardbus Bridge with ZV Support [1179:0617] (rev 20)
Subsystem: Toshiba America Info Systems Unknown device
[1179:0001]
Flags: bus master, slow devsel, latency 168, IRQ 11
Memory at 28100000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=0
Memory window 0: 20000000-21fff000 (prefetchable)
Memory window 1: 22000000-23fff000
I/O window 0: 00001000-000010ff
I/O window 1: 00001400-000014ff
16-bit legacy interface ports at 0001
00:0b.1 CardBus bridge [0607]: Toshiba America Info Systems ToPIC100 PCI
to Cardbus Bridge with ZV Support [1179:0617] (rev 20)
Subsystem: Toshiba America Info Systems Unknown device
[1179:0001]
Flags: bus master, slow devsel, latency 168, IRQ 11
Memory at 28101000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=09, sec-latency=0
Memory window 0: 24000000-25fff000 (prefetchable)
Memory window 1: 26000000-27fff000
I/O window 0: 00001800-000018ff
I/O window 1: 00002000-000020ff
16-bit legacy interface ports at 0001
00:0c.0 Multimedia audio controller [0401]: ESS Technology ES1978
Maestro 2E [125d:1978] (rev 10)
Subsystem: Toshiba America Info Systems ES1978 Maestro-2E
Audiodrive [1179:0001]
Flags: bus master, medium devsel, latency 64, IRQ 11
I/O ports at fc00 [size=256]
Capabilities: [c0] Power Management version 2
01:00.0 VGA compatible controller [0300]: S3 Inc. 86C270-294
Savage/IX-MV [5333:8c12] (rev 11) (prog-if 00 [VGA])
Subsystem: Toshiba America Info Systems 86C584 SuperSavage/IXC
Toshiba [1179:0001]
Flags: bus master, 66MHz, medium devsel, latency 248, IRQ 11
Memory at f0000000 (32-bit, non-prefetchable) [size=128M]
Expansion ROM at 28000000 [disabled] [size=64K]
Capabilities: [dc] Power Management version 1
Capabilities: [80] AGP version 1.0
06:00.0 Ethernet controller [0200]: Linksys, A Division of Cisco Systems
WMP11v4 802.11b PCI card [17fe:2120]
Subsystem: Linksys, A Division of Cisco Systems WMP11v4 802.11b
PCI card [17fe:2120]
Flags: medium devsel, IRQ 11
Memory at 26000000 (32-bit, non-prefetchable) [disabled]
[size=2K]
Capabilities: [40] Power Management version 2
Reply to: