Bug#404618: installation-report - sarge
Package: installation-reports
Boot method: CD & network [same results]
Image version: [Object]
URL=http://cdimage.debian.org/debian-cd/current/i386/iso-cd/debian-31r4-i386-binary-1.iso
URL=http://cdimage.debian.org/debian-cd/current/i386/iso-cd/debian-31r4-i386-netinst.iso
Date: <12/26/07 15:00>
Machine: <custom build>
Processor:Celeron (EM64T) 2.66GHz
Memory: 512MB
Partitions: <df -Tl will do; the raw partition table is preferred>
root@1[robert]# more /etc/fstab
# Pluggable devices are handled by uDev, they are not in fstab
/dev/sda1 / ext3 defaults,noatime 1 1
/dev/sda2 swap swap sw,pri=1 0 0
none /proc proc defaults 0 0
none /proc/bus/usb usbfs devmode=0666 0 0
none /dev/pts devpts mode=0622 0 0
none /sys sysfs defaults 0 0
/dev/sda3 /home ext3 defaults,noatime 1 2
# Dynamic entries below, identified by 'users' option
/dev/sdb1 /mnt/sdb1 vfat,ext3,ext2,reiserfs noauto,users,exec 0 0
root@1[robert]#
root@1[robert]# df -Tl
Filesystem Type 1K-blocks Used Available Use% Mounted on
/dev/sda1 ext3 9612252 2023616 7100356 23% /
/dev/sda3 ext3 23360528 134300 22039560 1% /home
tmpfs tmpfs 224580 0 224580 0% /dev/shm
tmpfs tmpfs 10240 92 10148 1% /dev
Output of lspci and lspci -n:
root@1[robert]# lspci
0000:00:00.0 Host bridge: ATI Technologies Inc: Unknown device 5a33 (rev 01)
0000:00:01.0 PCI bridge: ATI Technologies Inc: Unknown device 5a3f
0000:00:11.0 IDE interface: ATI Technologies Inc ATI 437A Serial ATA Controller (rev 80)
0000:00:12.0 IDE interface: ATI Technologies Inc ATI 4379 Serial ATA Controller (rev 80)
0000:00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (rev 80)
0000:00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (rev 80)
0000:00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host Controller (rev 80)
0000:00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 81)
0000:00:14.1 IDE interface: ATI Technologies Inc Standard Dual Channel PCI IDE Controller ATI (rev 80)
0000:00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge (rev 80)
0000:00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge (rev 80)
0000:01:05.0 VGA compatible controller: ATI Technologies Inc: Unknown device 5a61
0000:02:02.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
root@1[robert]# lspci -n
0000:00:00.0 0600: 1002:5a33 (rev 01)
0000:00:01.0 0604: 1002:5a3f
0000:00:11.0 0101: 1002:437a (rev 80)
0000:00:12.0 0101: 1002:4379 (rev 80)
0000:00:13.0 0c03: 1002:4374 (rev 80)
0000:00:13.1 0c03: 1002:4375 (rev 80)
0000:00:13.2 0c03: 1002:4373 (rev 80)
0000:00:14.0 0c05: 1002:4372 (rev 81)
0000:00:14.1 0101: 1002:4376 (rev 80)
0000:00:14.3 0601: 1002:4377 (rev 80)
0000:00:14.4 0604: 1002:4371 (rev 80)
0000:01:05.0 0300: 1002:5a61
0000:02:02.0 0200: 10ec:8139 (rev 10)
root@1[robert]#
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [O]
Configure network HW: [O]
Config network: [O]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [E] Error Message: "No partitionable media were found."
Partition hard drives: [E] Error Message: "No partitionable media were found."
Create file systems: [ ]
Mount partitions: [ ]
Install base system: [ ]
Install boot loader: [ ]
Reboot: [ ]
Comments/Problems:
Install script doesn't seem to detect SATA hard drives, either raw or ext3 partitions.
The only error message that comes up is: "No partitionable media were found."
I hope someone can help.
Reply to: