Bug#404437: installation-reports
Package: installation-reports
Debian-installer-version: 12/22/06
http://cdimage.debian.org/cdimage/daily-builds/daily/arch-latest/amd64/iso-cd/debian-testing-amd64-netinst.iso
uname -a: Linux spade 2.6.18-3-amd64 #1 SMP Sun Dec 10
19:57:44 CET 2006 x86_64 GNU/Linux
Date: 12/22/06
Method: netist CD, used ftp.debian.org to download
needed pakages
Machine:IBM Thinkpad T60
Processor: Core 2 Duo 2.0 GHz
Memory: 1024 MB
Root Device: SATA
Root Size/partition table: Disk /dev/sda: 100.0 GB,
100030242816 bytes
255 heads, 63 sectors/track, 12161 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id
System
/dev/sda1 * 1 2550 20482843+ 7
HPFS/NTFS
/dev/sda2 11572 12161 4732560 12
Compaq diagnostics
Partition 2 does not end on cylinder boundary.
/dev/sda3 2551 2562 96390 83
Linux
/dev/sda4 2563 11571 72364792+ 5
Extended
/dev/sda5 2563 11199 69376671 83
Linux
/dev/sda6 11200 11571 2988058+ 82
Linux swap / Solaris
Output of lspci and lspci -n:
lspci:
00:00.0 Host bridge: Intel Corporation Mobile
945GM/PM/GMS/940GML and 945GT Express Memory
Controller Hub (rev 03)
00:01.0 PCI bridge: Intel Corporation Mobile
945GM/PM/GMS/940GML and 945GT Express PCI Express Root
Port (rev 03)
00:1b.0 Audio device: Intel Corporation 82801G (ICH7
Family) High Definition Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7
Family) PCI Express Port 1 (rev 02)
00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7
Family) PCI Express Port 2 (rev 02)
00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7
Family) PCI Express Port 3 (rev 02)
00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7
Family) PCI Express Port 4 (rev 02)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7
Family) USB UHCI #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7
Family) USB UHCI #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7
Family) USB UHCI #3 (rev 02)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7
Family) USB UHCI #4 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7
Family) USB2 EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI
Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation 82801GBM
(ICH7-M) LPC Interface Bridge (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7
Family) IDE Controller (rev 02)
00:1f.2 SATA controller: Intel Corporation
82801GBM/GHM (ICH7 Family) Serial ATA Storage
Controller AHCI (rev 02)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family)
SMBus Controller (rev 02)
01:00.0 VGA compatible controller: ATI Technologies
Inc Radeon Mobility X1400
02:00.0 Ethernet controller: Intel Corporation 82573L
Gigabit Ethernet Controller
03:00.0 Network controller: Intel Corporation
PRO/Wireless 3945ABG Network Connection (rev 02)
15:00.0 CardBus bridge: Texas Instruments PCI1510 PC
card Cardbus Controller
lspci -n:
00:00.0 0600: 8086:27a0 (rev 03)
00:01.0 0604: 8086:27a1 (rev 03)
00:1b.0 0403: 8086:27d8 (rev 02)
00:1c.0 0604: 8086:27d0 (rev 02)
00:1c.1 0604: 8086:27d2 (rev 02)
00:1c.2 0604: 8086:27d4 (rev 02)
00:1c.3 0604: 8086:27d6 (rev 02)
00:1d.0 0c03: 8086:27c8 (rev 02)
00:1d.1 0c03: 8086:27c9 (rev 02)
00:1d.2 0c03: 8086:27ca (rev 02)
00:1d.3 0c03: 8086:27cb (rev 02)
00:1d.7 0c03: 8086:27cc (rev 02)
00:1e.0 0604: 8086:2448 (rev e2)
00:1f.0 0601: 8086:27b9 (rev 02)
00:1f.1 0101: 8086:27df (rev 02)
00:1f.2 0106: 8086:27c5 (rev 02)
00:1f.3 0c05: 8086:27da (rev 02)
01:00.0 0300: 1002:7145
02:00.0 0200: 8086:109a
03:00.0 0280: 8086:4227 (rev 02)
15:00.0 0607: 104c:ac56
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] =
didn't try it
Initial boot worked: [O]
Configure network HW: [O]
Config network: [O]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Create file systems: [O]
Mount partitions: [O]
Install base system: [O]
Install boot loader: [O]
Reboot: [O]
Comments/Problems:
Installation went fine. I initially tried using the
daily build businesscard installer but the CD would
not boot.
The system is set up to dual boot windows and Debian.
I used the NT bootloader because it is needed to
preserve the function of the Thinkvantage button.
Before the install I resized the windows partition
using gpart from the sysresccd.
I started the installer in expert mode. All the
hardware checks went fine. We use DHCP and the
installer set that up correctly. I made a 100 MB /boot
partition and installed Grub on it. The rest of the
free space I used for / and swap.
I installed the 2.6.18-3 kernel. In the install
additional software section I selected Base and
Laptop, but not Desktop
Before finishing the installation I used
dd if=/dev/sda3 of=grub.mbr bs=512 count=1
to make a file grub.mbr from the /boot partition
I copyed this file to the windows partition and
pointed the NT bootloader at it to load Grub. Then
Grub loads Debian.
After these changes I rebooted the system and it came
up fine.
For some reason xfonts-base had not been installed
(maybe because I did not check Desktop?) so X did not
work. I installed the
__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com
Reply to: