--- Begin Message ---
Package: installation-reports
Boot method: external firewire cd
Image version: http://cdimage.debian.org/cdimage/daily-builds/daily/arch-latest/powerpc/iso-cd/debian-testing-powerpc-netinst.iso (from 5/3/06)
Date: 5/03/06 07:45
Machine: Xserve G5 cluster node (headless), external firewire, serial console only (different box from Bug#365844, but identical)
Processor: Dual PowerPC970 (Apple RackMac3,1 5.1.7f0 BootROM built on 05/06/04 at 15:57:06)
Memory: 2GB
Partitions: none yet; testing installer bootability
Output of lspci and lspci -n: N/A
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [E]
Configure network HW: [ ]
Config network: [ ]
Detect CD: [ ]
Load installer modules: [ ]
Detect hard drives: [ ]
Partition hard drives: [ ]
Create file systems: [ ]
Mount partitions: [ ]
Install base system: [ ]
Install boot loader: [ ]
Reboot: [ ]
Comments/Problems:
Boot crashes right after 'core99_setup_cpu 0 done' message. Note that this
installation attempt was identical to that in Bug#365844. A different Xserve
box was used, although an identical model to the box in Bug#365844 (both are
members of the same Xserve cluster).
The only difference between the two machines is that the USB ports in this
one have been used, whereas the USB ports in the box from Bug#365844 have
never been touched. NO USB devices were plugged in at the time of the
attempt. The only external device was the firewire cd.
Note also that this box and all it's ports work fine under Mac OS X
See Bug#365730, which may be a duplicate.
Console log:
Apple RackMac3,1 5.1.7f0 BootROM built on 05/06/04 at 15:57:06
Copyright 1994-2004 Apple Computer, Inc.
All Rights Reserved.
Welcome to Open Firmware, the system time and date is: 11:01:37 05/03/2006
To continue booting, type "mac-boot" and press return.
To shut down, type "shut-down" and press return.
ok
0 > dev fw ls
ff9f1a68: /node@00d04b3815067a2f
ff9f1c60: /sbp-2@c000
ff9f1ea8: /disk@0
ok
0 > devalias cd /ht/pci@5/firewire/node@00d04b3815067a2f/sbp-2@c000/disk@0 ok
0 > dir cd:,\install
sbp2:Open ->login?
speed=ffffffff 2 2 -
Size/ GMT File/Dir
bytes date time TYPE CRTR Name
781 5/ 3/ 6 3: 4:23 ???? ???? boot.msg
1855 5/ 3/ 6 3: 4:23 tbxi UNIX ofboot.b
2319 5/ 3/ 6 3: 4:23 ???? ???? pegasos
1/ 1/ 4 0: 0: 0 powerpc
1/ 1/ 4 0: 0: 0 powerpc64
149740 3/ 2/ 6 16:11: 8 boot UNIX yaboot
1138 5/ 3/ 6 3: 4:23 conf UNIX yaboot.conf
ok
0 > boot cd:,\install\yaboot
sbp2:Open ->login?
speed=ffffffff 2 2 load-size=248ec adler32=881546ed
Loading ELF
sbp2:Open ->login?
speed=ffffffff 2 2
sbp2:Open ->login?
speed=ffffffff 2 2
sbp2:Open ->login?
speed=ffffffff 2 2
sbp2:Open ->login?
speed=ffffffff 2 2
sbp2:Open ->login?
speed=ffffffff 2 2 Config file read, 1138 bytes
sbp2:Open ->login?
speed=ffffffff 2 2
sbp2:Open ->login?
speed=ffffffff 2 2 \
sbp2:Open ->login?
speed=ffffffff 2 2
sbp2:Open ->login?
speed=ffffffff 2 2
sbp2:Open ->login?
speed=ffffffff 2 2 Welcome to Debian GNU/Linux etch!
This is a Debian installation CDROM,
built on 20060503.
The default option is 'install'. For maximum
control, you can use the 'expert' option.
If the system fails to boot at all (the typical
symptom is a white screen which doesn't go away),
use 'install video=ofonly' or 'expert video=ofonly'.
The plain options are for the powerpc family of
processors (from 601 to G4). The *64 options are for
64bit powerpc processors, which include the IBM
Power3, Power4, Power5, ... boxes, as well as the
Apple G5 boxes. Press the tab key for a list of
options, or type 'help' for help.
************************************
If in doubt, just choose 'install', and if that
doesn't work, try 'install video=ofonly'.
************************************
Welcome to yaboot version 1.3.13
Enter "help" to get some basic usage information
sbp2:Open ->login?
speed=ffffffff 2 2 boot:
* install expert install64
expert64
boot: expert64 video=ofonly console=ttyS0,57600 debug dobladecenter
Please wait, loading kernel...
sbp2:Open ->login?
speed=ffffffff 2 2
sbp2:Open ->login?
speed=ffffffff 2 2
sbp2:Open ->login?
speed=ffffffff 2 2
sbp2:Open ->login?
speed=ffffffff 2 2
sbp2:Open ->login?
speed=ffffffff 2 2 Elf64 kernel loaded...
Loading ramdisk...
sbp2:Open ->login?
speed=ffffffff 2 2
sbp2:Open ->login?
speed=ffffffff 2 2
sbp2:Open ->login?
speed=ffffffff 2 2
sbp2:Open ->login?
speed=ffffffff 2 2
sbp2:Open ->login?
speed=ffffffff 2 2 ramdisk loaded at 01a00000, size: 3565 Kbytes
OF stdout device is: /ht@0,f2000000/pci@3/mac-io@7/escc@13000/ch-a@13020
command line: ro ramdisk_size=10240 DEBCONF_PRIORITY=low devfs=mount,dall init=/linuxrc -- video=ofonly console=ttyS0,57600 debug dobladecenter
memory layout at init:
memory_limit : 0000000000000000 (16 MB aligned)
alloc_bottom : 0000000001d7c000
alloc_top : 0000000030000000
alloc_top_hi : 0000000080000000
rmo_top : 0000000030000000
ram_top : 0000000080000000
Looking for displays
copying OF device tree ...
Building dt strings...
Building dt structure...
Device tree strings 0x0000000001e7d000 -> 0x0000000001e7e366
Device tree struct 0x0000000001e7f000 -> 0x0000000001e92000
Calling quiesce ...
DO-QUIESCE finishedreturning from prom_init
Hello World !
Page orders: linear mapping = 24, others = 12
Found initrd at 0xc000000001a00000:0xc000000001d7b5d5
Found U3 memory controller & host bridge @ 0xf8000000 revision: 0x35
Mapped at 0xd000080080000000
Found a K2 mac-io controller, rev: 96, mapped at 0xd000080080041000
PowerMac motherboard: XServe G5
boot stdout isn't a display !
DART: table not allocated, using direct DMA
CF000100
MM Init
CF000100
MM Init Done
CF000012
Setup Arch
CF000015
Setup Done
Starting Linux PPC64 #2 SMP Tue Apr 25 15:26:45 CEST 2006
-----------------------------------------------------
ppc64_pft_size = 0x0
ppc64_interrupt_controller = 0x1
platform = 0x400
physicalMemorySize = 0x80000000
ppc64_caches.dcache_line_size = 0x80
ppc64_caches.icache_line_size = 0x80
htab_address = 0xc00000007c000000
htab_hash_mask = 0x3ffff
-----------------------------------------------------
[boot]0100 MM Init
[boot]0100 MM Init Done
Linux version 2.6.16-1-powerpc64 (Debian 2.6.16-10) (waldi@debian.org) (gcc version 4.0.3 (Debian 4.0.3-1)) #2 SMP Tue Apr 25 15:26:45 CEST 2006
[boot]0012 Setup Arch
Top of RAM: 0x80000000, Total RAM: 0x80000000
Memory hole size: 0MB
Found U3-AGP PCI host bridge. Firmware bus number: 240->255
Can't get bus-range for /ht@0,f2000000, assume bus 0
Found U3-HT PCI host bridge. Firmware bus number: 0->239
PCI Host 0, io start: 400000; io end: bfffff
PCI Host 1, io start: 0; io end: 3fffff
via-pmu: Server Mode is disabled
PMU driver v2 initialized for Core99, firmware: 0c
nvram: Checking bank 0...
nvram: gen0=116, gen1=115
nvram: Active bank is: 0
nvram: OF partition at 0x410
nvram: XP partition at 0x1020
nvram: NR partition at 0x1120
[boot]0015 Setup Done
Built 1 zonelists
Kernel command line: ro ramdisk_size=10240 DEBCONF_PRIORITY=low devfs=mount,dall init=/linuxrc -- video=ofonly console=ttyS0,57600 debug dobladecenter
mpic: Setting up MPIC " MPIC 1 " version 1.2 at 80040000, max 4 CPUs
mpic: ISU size: 120, shift: 7, mask: 7f
mpic: Initializing for 120 sources
mpic: Setting up MPIC " MPIC 2 " version 1.2 at f8040000, max 4 CPUs
mpic: ISU size: 124, shift: 7, mask: 7f
mpic: Initializing for 124 sources
PID hash table entries: 4096 (order: 12, 131072 bytes)
time_init: decrementer frequency = 33.333333 MHz
time_init: processor frequency = 2000.000000 MHz
Page orders: linear mapping = 24, others = 12
Found initrd at 0xc000000001a00000:0xc000000001d7b5d5
Found U3 memory controller & host bridge @ 0xf8000000 revision: 0x35
Mapped at 0xd000080080000000
Found a K2 mac-io controller, rev: 96, mapped at 0xd000080080041000
PowerMac motherboard: XServe G5
boot stdout isn't a display !
DART: table not allocated, using direct DMA
Starting Linux PPC64 #2 SMP Tue Apr 25 15:26:45 CEST 2006
-----------------------------------------------------
ppc64_pft_size = 0x0
ppc64_interrupt_controller = 0x1
platform = 0x400
physicalMemorySize = 0x80000000
ppc64_caches.dcache_line_size = 0x80
ppc64_caches.icache_line_size = 0x80
htab_address = 0xc00000007c000000
htab_hash_mask = 0x3ffff
-----------------------------------------------------
[boot]0100 MM Init
[boot]0100 MM Init Done
Linux version 2.6.16-1-powerpc64 (Debian 2.6.16-10) (waldi@debian.org) (gcc version 4.0.3 (Debian 4.0.3-1)) #2 SMP Tue Apr 25 15:26:45 CEST 2006
[boot]0012 Setup Arch
Top of RAM: 0x80000000, Total RAM: 0x80000000
Memory hole size: 0MB
Found U3-AGP PCI host bridge. Firmware bus number: 240->255
Can't get bus-range for /ht@0,f2000000, assume bus 0
Found U3-HT PCI host bridge. Firmware bus number: 0->239
PCI Host 0, io start: 400000; io end: bfffff
PCI Host 1, io start: 0; io end: 3fffff
via-pmu: Server Mode is disabled
PMU driver v2 initialized for Core99, firmware: 0c
nvram: Checking bank 0...
nvram: gen0=116, gen1=115
nvram: Active bank is: 0
nvram: OF partition at 0x410
nvram: XP partition at 0x1020
nvram: NR partition at 0x1120
On node 0 totalpages: 524288
DMA zone: 524288 pages, LIFO batch:31
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 0 pages, LIFO batch:0
HighMem zone: 0 pages, LIFO batch:0
[boot]0015 Setup Done
Built 1 zonelists
Kernel command line: ro ramdisk_size=10240 DEBCONF_PRIORITY=low devfs=mount,dall init=/linuxrc -- video=ofonly console=ttyS0,57600 debug dobladecenter
mpic: Setting up MPIC " MPIC 1 " version 1.2 at 80040000, max 4 CPUs
mpic: ISU size: 120, shift: 7, mask: 7f
mpic: Initializing for 120 sources
mpic: Setting up MPIC " MPIC 2 " version 1.2 at f8040000, max 4 CPUs
mpic: ISU size: 124, shift: 7, mask: 7f
mpic: Initializing for 124 sources
PID hash table entries: 4096 (order: 12, 131072 bytes)
time_init: decrementer frequency = 33.333333 MHz
time_init: processor frequency = 2000.000000 MHz
Console: colour dummy device 80x25
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
freeing bootmem node 0
Memory: 2020836k/2097152k available (3392k kernel code, 76316k reserved, 920k data, 304k bss, 236k init)
Calibrating delay loop... 66.56 BogoMIPS (lpj=33280)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 256
smp_core99_probe
PowerMac SMP probe found 2 cpus
KeyWest i2c @0xf8001003 irq 128 /u3@0,f8000000/i2c@f8001000
channel 0 bus <multibus>
channel 1 bus <multibus>
KeyWest i2c @0x80018000 irq 26 /ht@0,f2000000/pci@3/mac-io@7/i2c@18000
channel 0 bus <multibus>
PMU i2c /ht@0,f2000000/pci@3/mac-io@7/via-pmu@16000/pmu-i2c
channel 1 bus <multibus>
channel 2 bus <multibus>
Processor timebase sync using Pulsar i2c clock
requesting IPIs ...
IPIs requested...
smp_core99_kick_cpu
smp_core99_kick_cpu done
Processor 1 found.
Brought up 2 CPUs
core99_setup_cpu 0 done
Unable to handle kernel paging request for data at address 0xc00000007c4d7480
Faulting instruction address: 0xc00000000002cc80
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=32 NUMA POWERMAC
Modules linked in:
NIP: C00000000002CC80 LR: C00000000002AAFC CTR: C0000000000467D0
REGS: c00000007ff5b3b0 TRAP: 0300 Not tainted (2.6.16-1-powerpc64)
MSR: 9000000000001032 <ME,IR,DR> CR: 28000082 XER: 000FFFFF
DAR: C00000007C4D7480, DSISR: 0000000040010000
TASK = c00000007ff47820[1] 'swapper' THREAD: c00000007ff58000 CPU: 1
GPR00: 000001E137135EA0 C00000007FF5B630 C000000000439230 00000000004D7480
GPR04: 0000000000000194 F09B89AF5001CFA8 0000000000000000 0000000000000000
GPR08: 0000F09B89AF5000 000001E137135EA0 0000000000000008 C00000007C4D7480
GPR12: 9000000000009032 C00000000037C100 000000000000007D 00000000FFFB6EF6
GPR16: 0000000000000000 C00000000043C8B0 0000000000000000 0000000000012C40
GPR20: 0000000000A00000 000000000001B186 0000000000000000 0000004601187920
GPR24: 000000000001E1B1 D000000000000000 0000000000000000 000000000003FFFF
GPR28: 0000000F09B89AE9 F09B89AF5001CFA8 0000000000000000 00000001FE4C0791
NIP [C00000000002CC80] .native_hpte_updatepp+0x68/0x290
LR [C00000000002AAFC] .htab_call_hpte_updatepp+0x4/0x18
Call Trace:
[C00000007FF5B630] [C000000000393918] 0xc000000000393918 (unreliable)
[C00000007FF5B6D0] [C00000000002AAFC] .htab_call_hpte_updatepp+0x4/0x18
[C00000007FF5B7D0] [C00000000002A78C] .hash_page+0x13c/0x158
[C00000007FF5B840] [C000000000004734] .do_hash_page+0x34/0x40
--- Exception: 301 at .touch_cache+0x90/0x104
LR = .measure_one+0xec/0x174
[C00000007FF5BB30] [C00000000004A960] .measure_one+0xb0/0x174 (unreliable)
[C00000007FF5BBF0] [C00000000004BEB8] .build_sched_domains+0xbc0/0x1014
[C00000007FF5BE70] [C00000000032E2A4] .sched_init_smp+0x34/0x48
[C00000007FF5BF00] [C000000000009408] .init+0x1bc/0x3d8
[C00000007FF5BF90] [C000000000021518] .kernel_thread+0x4c/0x68
Instruction dump:
7cbd2b78 7d290214 78a04dc2 e9290010 e96b0000 7c094878 7d6b1a14 79283e24
419e0008 61080004 39400008 7c2004ac <7d2058a8> 7d205378 7c0059ad 40a2fff4
--- End Message ---