Bug#288217: Debian Testing - Installation Report
Package: installation-reports
INSTALL REPORT
Debian-installer-version: rc2 (downloaded around Dec 20, 2004)
uname -a: Linux debian 2.4.27-1-386 #1 Fri Sep 3 06:24:46 UTC 2004 i586
GNU/Linux
Date: January 2, 2005 around 6:00am EST
Method: Net install, booted from a CDROM, from mirrors.kernel.org, and
not proxied.
Machine: Custom AMD K6-2 500mhz computer
Processor: AMD K6-2 500mhz Computer
Memory: 256MB memory.
Root Device: IDE? Yes SCSI? No Name of device? /dev/hda (Maxtor 20GB
hard drive)
Root Size/partition table:
# fdisk -l /dev/hda
Disk /dev/hda: 20.4 GB, 20490559488 bytes
255 heads, 63 sectors/track, 2491 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/hda1 * 1 823 6610716 b W95 FAT32
/dev/hda2 824 2491 13398210 f W95 Ext'd (LBA)
/dev/hda5 824 1078 2048256 b W95 FAT32
/dev/hda6 1079 1141 506016 82 Linux swap
/dev/hda7 1142 1811 5381743+ 83 Linux
/dev/hda8 1812 2491 5462068+ 83 Linux
/dev/hda8 is / (ext3)
/dev/hda7 is another linux distribution (suse 9.0, using reiserfs)
Output of lspci and lspci -n:
0000:00:00.0 Host bridge: ALi Corporation M1541 (rev 04)
0000:00:01.0 PCI bridge: ALi Corporation M1541 PCI to AGP Controller
(rev 04)
0000:00:02.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
0000:00:07.0 ISA bridge: ALi Corporation M1533 PCI to ISA Bridge
[Aladdin IV] (rev c3)
0000:00:09.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
0000:00:0f.0 IDE interface: ALi Corporation M5229 IDE (rev c2)
0000:01:00.0 VGA compatible controller: S3 Inc. Savage 4 (rev 04)
0000:00:00.0 0600: 10b9:1541 (rev 04)
0000:00:01.0 0604: 10b9:5243 (rev 04)
0000:00:02.0 0c03: 10b9:5237 (rev 03)
0000:00:07.0 0601: 10b9:1533 (rev c3)
0000:00:09.0 0200: 10ec:8139 (rev 10)
0000:00:0f.0 0101: 10b9:5229 (rev c2)
0000:01:00.0 0300: 5333:8a22 (rev 04)
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [O]
Configure network HW: [O]
Config network: [O]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Create file systems: [O]
Mount partitions: [O]
Install base system: [O]
Install boot loader: [O]
Reboot: [O]
Comments/Problems:
After X was setup and it loaded, a second, un-moveable mouse cursor was
visible on the screen that could not be removed from the screen (until a
certain amount of time passed, which was a few minutes or so).
I am not sure why the second cursor appears since I only have one mouse
(a PS/2 one) connected to this system.
Reply to: