Bug#328882: Package: installation-reports
Package: installation-reports
Debian-installer-version: http://cdimage.debian.org/debian-cd/3.1_r0a/hppa/
iso-cd/debian-31r0a-hppa-netinst.iso, 2005.08.21
uname -a: Linux cherokee 2.6.8-2-32-smp #1 SMP Mon Feb 7 22:19:10 EST 2005
parisc GNU/Linux
Date: 2005.11.14
Method: Installed from netinst.iso via SESCSI.1.0, TOSHIBA CD-ROM XM-6201TA
apt'ed from ftp://debian.chicago.edu
Machine: Visualize c200 / Raven U+ - 9000/782
Firmware Version 6.0
Duplex Console IO Dependent Code (IODC) revision 1
------------------------------------------------------------------------------
(c) Copyright 1995-1998, Hewlett-Packard Company, All rights reserved
------------------------------------------------------------------------------
Processor Speed State Coprocessor State I/D Cache
--------- -------- --------------------- ----------------- -------------
0 200 MHz Active Functional 512 KB/1 MB
Central Bus Speed (in MHz) : 120
Available memory (bytes) : 1610612736
Good memory required (bytes): 0 (Not Set by OS)
Primary boot path: FWSCSI.1.0
Alternate boot path: SESCSI.1.0
Console path: SERIAL_1.9600.8.none
Keyboard path: PS2
Processor: PA-8200
Memory:
MEMORY STATUS TABLE
Slot Size(a+b) Status
---- --------- ------
0a/b 256MB Configured
1a/b 256MB Configured
2a/b 256MB Configured
3a/b 256MB Configured
4a/b 256MB Configured
5a/b 256MB Configured
---------
TOTAL 1536MB
Root Device:
Primary boot path: FWSCSI.1.0
Western Digital Enterprise 4360 Single-ended Ultra Fast Wide SCSI-3
Identifies as "WDIGTL ENTERPRISE"
Root Size/partition table:
cherokee:~# fdisk -l
Disk /dev/sda: 4359 MB, 4359768576 bytes
255 heads, 63 sectors/track, 530 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sda1 1 4 32098+ f0 Linux/PA-RISC boot
/dev/sda2 5 20 128520 83 Linux
/dev/sda3 21 530 4096575 5 Extended
/dev/sda5 * 21 44 192748+ 83 Linux
/dev/sda6 45 232 1510078+ 83 Linux
/dev/sda7 233 311 634536 83 Linux
/dev/sda8 312 339 224878+ 82 Linux swap / Solaris
/dev/sda9 340 352 104391 83 Linux
/dev/sda10 353 530 1429753+ 83 Linux
cherokee:~# mount
/dev/sda5 on / type ext3 (rw,errors=remount-ro)
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
devpts on /dev/pts type devpts (rw,gid=5,mode=620)
tmpfs on /dev/shm type tmpfs (rw)
/dev/sda2 on /boot type ext2 (rw)
/dev/sda10 on /home type ext3 (rw)
/dev/sda9 on /tmp type ext3 (rw)
/dev/sda6 on /usr type ext3 (rw)
/dev/sda7 on /var type ext3 (rw)
Output of lspci and lspci -n:
cherokee:~#lspci
0000:00:03.0 Ethernet controller: Digital Equipment Corporation DECchip 21142/43
(rev 21)
0000:00:13.0 SCSI storage controller: LSI Logic / Symbios Logic 53c875 (rev 04)
0000:00:14.0 Ethernet controller: Digital Equipment Corporation DECchip 21142/43
(rev 30)
0000:01:04.0 Display controller: Hewlett-Packard Company A4977A Visualize EG (re
v 03)
cherokee:~# lspci -n
0000:00:03.0 0200: 1011:0019 (rev 21)
0000:00:13.0 0100: 1000:000f (rev 04)
0000:00:14.0 0200: 1011:0019 (rev 30)
0000:01:04.0 0380: 103c:1005 (rev 03
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [E]
Configure network HW: [O]
Config network: [E]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Create file systems: [O]
Mount partitions: [O]
Install base system: [O]
Install boot loader: [O]
Reboot: [O]
Comments/Problems:
Have no display, keyboard, or mouse attached to this system. Am connected
via ttyS0 over null-modem cable. Both tulips have known good cat5e
cable connections to a 100baseTx-FD switch/router serving DHCP leases.
Issued "BOot ALTernate" under BCH, issued 'y' to interact with the IPL, and
accepted the following defaults:
0/vmlinux root=/dev/ram initrd=0/ramdisk ramdisk_size=16384 init=/linuxrc
console=ttyS0 TERM=vt102
This gave the following warnings and errors:
Warning: kernel name doesn't end with 32 or 64 -- Guessing... Choosing 32-bit
kernelELF32 executable
[SNIP]
RAMDISK: Compressed image found at block 0
RAMDISK: incomplete write (-28 != 32768) 16777216
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 316k freed
Setting up filesystem, please wait ...
attempt to access beyond end of device
ram0: rw=0, want=40650, limit=32768
[SNIP]
Based on these messages, tried the following kernel command line:
0/vmlinux32 root=/dev/ram initrd=0/ramdisk ramdisk_size=32768 init=/linuxrc
console=ttyS0 TERM=vt102
This got past the initial boot stage, and allowed the install to continue.
During the install, the onboard and addin tulips detect fine, but neither one
will get a DHCP lease during the "Configuring the network with DHCP" phase.
Chose "Configure network manually" and entered values appropriate for
the network.
Still no connectivity on either net interface.
Aborted the intial install at the "Configure apt" stage and edited /etc/network/
interfaces as follows:
auto eth0
iface eth0 inet dhcp
auto eth1
iface eth1 inet dhcp
At this point, "ifup eth0" gives a valid DHCP lease on the addin NIC, while a
timeout is received for eth1 (onboard). "exit" at the prompt allows
the install to continue. After a reboot following the initial install, the
add-in tulip becomes eth1 instead of eth0.
Have tried known good straight-through and crossover cables, forced "COnfigure
LanConfig 100/Full_dx" in BCH, and issued "mii-tool -R -F 100baseTx-FD" at the
prompt. None of these allow the builtin tulip to detect physical media at any
time.
Is this the discover1 bug, or something else entirely? More info. available at:
http://dhbarr.freeshell.org/c200/lspci-vv.txt
http://dhbarr.freeshell.org/c200/dmesg.txt
Thanks in Advance,
-dhbarr.
Reply to: