Package: installation-reports INSTALL REPORT Debian-installer-version: Thur 17 Mar, ftp.no.debian.org uname -a: Linux hunnicut 2.4.18-386 #2 Sun Apr 14 10:38:08 EST 2002 i586 unknown Date: Fri 18 Mar, 17:00-ish CET Method: Grabbed netboot.tar.gz, created etherboot-image and -floppy with serial console. Etherboot, TFTP and DHCP. Installed Woody from ftp.no.debian.org Machine: Installation was carried out on my desktop (AMD Athlon XP 1800+, 256MB RAM), after the initial try on a Intel Pentium 100MHz, 32MB RAM failed due to lack of memory. Putting the disk back into the Pentium-machine worked nicely. Processor: Pentium 100MHz / Athlon XP 1800+ (1500MHz) Memory: 32MB / 256MB Root Device: IDE, Seagate ST310014ACE Root Size/partition table: Disk /dev/hda: 255 heads, 63 sectors, 1245 cylinders Units = cylinders of 16065 * 512 bytes Device Boot Start End Blocks Id System /dev/hda1 * 1 34 273073+ 83 Linux # /boot /dev/hda2 35 1245 9727357+ 5 Extended /dev/hda5 35 472 3518203+ 83 Linux /dev/hda6 473 692 1767118+ 83 Linux /dev/hda7 693 759 538146 82 Linux swap /dev/hda8 760 797 305203+ 83 Linux /dev/hda9 798 1245 3598528+ 83 Linux mount: /dev/hda1 / ext3 defaults 0 1 /dev/hda9 /home ext3 nodev,nosuid,noexec 0 2 /dev/hda8 /tmp ext3 nodev,nosuid 0 2 /dev/hda5 /usr ext3 nodev 0 2 /dev/hda6 /var ext3 nodev 0 2 /dev/hda7 none swap sw 0 0 Output of lspci and lspci -n: 00:00.0 Host bridge: VIA Technologies, Inc. VT82C576 3V [Apollo Master] (rev 02) 00:01.0 IDE interface: VIA Technologies, Inc. VT82C416MV (rev 04) 00:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139 (rev 10) 00:0b.0 Ethernet controller: Intel Corp. 82557 [Ethernet Pro 100] (rev 08) 00:00.0 Class 0600: 1106:0576 (rev 02) 00:01.0 Class 0101: 1106:1571 (rev 04) 00:0a.0 Class 0200: 10ec:8139 (rev 10) 00:0b.0 Class 0200: 8086:1229 (rev 08) Base System Installation Checklist: [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it Initial boot worked: [O] Configure network HW: [O] Config network: [O] Detect CD: [ ] Load installer modules: [O] Detect hard drives: [O] Partition hard drives: [O] Create file systems: [O] Mount partitions: [O] Install base system: [O] Install boot loader: [O] Reboot: [O] Comments/Problems: My only problem was that the d-i rc2-netboot-image in Sarge on ftp.no.debian.org was broken. http://www.debian.org/devel/debian-installer/News/2005/20050301 explained that. Using the d-i-netboot from Sid worked better, and I didn't have to compile a new kernel for it, again. ;-)
Attachment:
signature.asc
Description: Digital signature