Bug#299824: installation report
Package: installation-reports
Debian-installer-version: RC-2
uname -a: Linux obelix 2.6.8 #1 Tue Mar 15 18:06:12 CET 2005 i686 GNU/Linux
Date: March 9 2005
Method: I performed a network install from ftp.nl.debian.org booting a netinst cd.
Machine: AMD64 (I performed an i386 install)
Processor: AMD64 2800+
Memory: 512M
Root Device: Maxtor IDE disk (/dev/hda)
Root Size/partition table:
Device Boot Start End Blocks Id System mountpoint
/dev/hda1 * 1 2491 20008926 7 HPFS/NTFS not mounted
/dev/hda2 2492 12643 81545940 f W95 Ext'd (LBA) -
/dev/hda3 12644 17525 39214665 83 Linux /
/dev/hda5 2492 12455 80035798+ c W95 FAT32 (LBA) /windows
/dev/hda6 12456 12643 1510078+ 82 Linux swap -
Output of lspci and lspci -n:
0000:00:00.0 Host bridge: nVidia Corporation: Unknown device 00e1 (rev a1)
0000:00:01.0 ISA bridge: nVidia Corporation: Unknown device 00e0 (rev a2)
0000:00:01.1 SMBus: nVidia Corporation: Unknown device 00e4 (rev a1)
0000:00:02.0 USB Controller: nVidia Corporation: Unknown device 00e7 (rev a1)
0000:00:02.1 USB Controller: nVidia Corporation: Unknown device 00e7 (rev a1)
0000:00:02.2 USB Controller: nVidia Corporation: Unknown device 00e8 (rev a2)
0000:00:05.0 Bridge: nVidia Corporation: Unknown device 00df (rev a2)
0000:00:06.0 Multimedia audio controller: nVidia Corporation: Unknown device 00ea (rev a1)
0000:00:08.0 IDE interface: nVidia Corporation: Unknown device 00e5 (rev a2)
0000:00:0b.0 PCI bridge: nVidia Corporation: Unknown device 00e2 (rev a2)
0000:00:0e.0 PCI bridge: nVidia Corporation: Unknown device 00ed (rev a2)
0000:00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
0000:00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
0000:00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
0000:00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
0000:01:00.0 VGA compatible controller: ATI Technologies Inc RV350 AP [Radeon 9600]
0000:01:00.1 Display controller: ATI Technologies Inc RV350 AP [Radeon 9600] (Secondary)
0000:02:0c.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 46)
0000:00:00.0 0600: 10de:00e1 (rev a1)
0000:00:01.0 0601: 10de:00e0 (rev a2)
0000:00:01.1 0c05: 10de:00e4 (rev a1)
0000:00:02.0 0c03: 10de:00e7 (rev a1)
0000:00:02.1 0c03: 10de:00e7 (rev a1)
0000:00:02.2 0c03: 10de:00e8 (rev a2)
0000:00:05.0 0680: 10de:00df (rev a2)
0000:00:06.0 0401: 10de:00ea (rev a1)
0000:00:08.0 0101: 10de:00e5 (rev a2)
0000:00:0b.0 0604: 10de:00e2 (rev a2)
0000:00:0e.0 0604: 10de:00ed (rev a2)
0000:00:18.0 0600: 1022:1100
0000:00:18.1 0600: 1022:1101
0000:00:18.2 0600: 1022:1102
0000:00:18.3 0600: 1022:1103
0000:01:00.0 0300: 1002:4150
0000:01:00.1 0380: 1002:4170
0000:02:0c.0 0c00: 1106:3044 (rev 46)
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [O]
Configure network HW: [E]
Config network: [E]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Create file systems: [O]
Mount partitions: [O]
Install base system: [O]
Install boot loader: [O]
Reboot: [O]
Comments/Problems:
The installer didn't load the forcedeth network module. It dit, however, loadthe networking
module for my firewire port, so it went on to configuring the network using dhcp. That failed
since nothing was plugged in to the firewire port. I had to load the forcedeth module manually
and when I did everything worked fine until after the first reboot. At that time the firewire
port and forcedeth switched 'places': the firewire port, which was eth0, became eth1 and the
forcedeth, which was eth1, became eth0. After I fixed that, the rest of the installation went
smoothly.
Regards,
Alex Lubberts
Reply to: