Bug#276379: installation-reports
Package: installation-reports
Debian-installer-version:
http://cdimage.debian.org/pub/cdimage-testing/sid_d-i/i386/20041011/sarge-i386-netinst.iso
also
http://cdimage.debian.org/pub/cdimage-testing/sid_d-i/i386/pre-rc2/sarge-i386-netinst.iso
uname -a:
Linux samweis 2.4.27-1-386 #1 Fri Sep 3 06:24:46 UTC 2004 i686 GNU/Linux
Date:
Wed Oct 13 17:39:18 UTC 2004
Method:
I burned the iso on a CDRW powered on the machine and just hit enter.
Machine: Dell PowerEdge 1850
Processor:
Intel(R) Xeon(TM) CPU 2.80GHz
Memory: 1 GB (2 x 512 MB)
Root Device: PERC4i RAID Controller, RAID1 pre-configured
Root Size/partition table:
/dev/sda1 /boot 200 MB
/dev/sda2 swap 1 GB
/dev/sda3 / about 70 GB (the rest)
Output of lspci and lspci -n:
lspci is not on the boot cd. However I managed to install ssh before the
initial reboot. Here you go:
samweis:~# lspci
0000:00:00.0 Host bridge: Intel Corp. Server Memory Controller Hub (rev
09)
0000:00:02.0 PCI bridge: Intel Corp. Memory Controller Hub PCI Express
Port A0 (rev 09)
0000:00:04.0 PCI bridge: Intel Corp. Memory Controller Hub PCI Express
Port B0 (rev 09)
0000:00:05.0 PCI bridge: Intel Corp. Memory Controller Hub PCI Express
Port B1 (rev 09)
0000:00:06.0 PCI bridge: Intel Corp. Memory Controller Hub PCI Express
Port C0 (rev 09)
0000:00:1d.0 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB
UHCI #1 (rev 02)
0000:00:1d.1 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB
UHCI #2 (rev 02)
0000:00:1d.2 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB
UHCI #3 (rev 02)
0000:00:1d.7 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB2
EHCI Controller (rev 02)
0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev c2)
0000:00:1f.0 ISA bridge: Intel Corp. 82801EB/ER (ICH5/ICH5R) LPC Bridge
(rev 02)
0000:00:1f.1 IDE interface: Intel Corp. 82801EB/ER (ICH5/ICH5R) Ultra
ATA 100 Storage Controller (rev 02)
0000:01:00.0 PCI bridge: Intel Corp. 80332 [Dobson] I/O processor (rev
06)
0000:01:00.2 PCI bridge: Intel Corp. 80332 [Dobson] I/O processor (rev
06)
0000:02:0e.0 RAID bus controller: Dell PowerEdge Expandable RAID
controller 4 (rev 06)
0000:05:00.0 PCI bridge: Intel Corp. PCI Bridge Hub A (rev 09)
0000:05:00.2 PCI bridge: Intel Corp. PCI Bridge Hub B (rev 09)
0000:06:07.0 Ethernet controller: Intel Corp. 82541GI/PI Gigabit
Ethernet Controller (rev 05)
0000:09:0d.0 VGA compatible controller: ATI Technologies Inc Radeon
RV100 QY [Radeon 7000/VE]
samweis:~# lspci -n
0000:00:00.0 0600: 8086:3590 (rev 09)
0000:00:02.0 0604: 8086:3595 (rev 09)
0000:00:04.0 0604: 8086:3597 (rev 09)
0000:00:05.0 0604: 8086:3598 (rev 09)
0000:00:06.0 0604: 8086:3599 (rev 09)
0000:00:1d.0 0c03: 8086:24d2 (rev 02)
0000:00:1d.1 0c03: 8086:24d4 (rev 02)
0000:00:1d.2 0c03: 8086:24d7 (rev 02)
0000:00:1d.7 0c03: 8086:24dd (rev 02)
0000:00:1e.0 0604: 8086:244e (rev c2)
0000:00:1f.0 0601: 8086:24d0 (rev 02)
0000:00:1f.1 0101: 8086:24db (rev 02)
0000:01:00.0 0604: 8086:0330 (rev 06)
0000:01:00.2 0604: 8086:0332 (rev 06)
0000:02:0e.0 0104: 1028:0013 (rev 06)
0000:05:00.0 0604: 8086:0329 (rev 09)
0000:05:00.2 0604: 8086:032a (rev 09)
0000:06:07.0 0200: 8086:1076 (rev 05)
0000:09:0d.0 0300: 1002:5159
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [O]
Configure network HW: [O]
Config network: [E]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [E]
Partition hard drives: [O]
Create file systems: [O]
Mount partitions: [O]
Install base system: [O]
Install boot loader: [O]
Reboot: [E]
Comments/Problems:
Configure network hardware: The configuration of the network hardware
succeded. Actually it went by to fast to see anything. But I believe
that the e1000 module wasn't loaded. It got loaded later.
Config network:
The first try with dhcp failed, I had to retry it to get a ip address
from our dhcp server. One time I switched to another console and
noticed that the e1000 module was just loaded then. After that, the
auto configuration worked.
Detect hard drives:
This pace in the setup brought no error actually but I think the
megaraid2 module should be loaded before this. Which is not the case.
I did it manually in a shell on another console. Then I did "Detect
hardware" again and so the install process went on.
Reboot:
After the inital reboot, the kernel panics with "Kernel panic: Attempted
to kill init". A few lines before that error one can see the message
"bla ... megaraid.o ...init_module: No such device". This is not the
right module. I don't know where this gets loaded but it's wrong.
I also tried the pre-rc2 iso image and got the same errors there.
I also tried booting with "linux26" but that is even worse. There is
only the megaraid.ko module, which doesn't match.
Reply to: