installation report
Hey Listmembers
After submitting a bugreport it came to my attention that there is a
report template which should be used. I therefore submit my bugreport
again this time the prober way :)
---------------------------------------------------------------------
Package: installation-reports
Debian-installer-version:
http://cdimage.debian.org/pub/cdimage-testing/daily/i386/20041004/sarge-i386-netinst.iso
I've also used a never image since the last bugreport with the same
result.
uname -a: Linux (none) 2.6.7-386 Thu Jul 8 05:08:04: EDT 2004 i686 unknown
Date: ons okt 6 13:04:37 CEST 2004
Method: Boot from Cdrom
Machine: Dell Dimension 8400
Processor: 3Ghz Pentium 4
Memory: 1Gb Ram
Chipset: Intel 925X Express chipset
Graphics: 128Mb PCIe ATI Radeon X300SE
Root Device: Sata ide 160GB HD
Root Size/partition table:
Disk /dev/scsi/host0/bus0/target0/lun0/disc: 160.0 GB, 160000000000
bytes
255 heads, 63 sectors/track, 19452 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End
Blocks
Id System
/dev/scsi/host0/bus0/target0/lun0/part1 * 1 851
6835626
83 Linux
/dev/scsi/host0/bus0/target0/lun0/part2 852 19452
149412532+
f W95 Ext'd (LBA)
/dev/scsi/host0/bus0/target0/lun0/part5 852 1181
2650693+
82 Linux swap
/dev/scsi/host0/bus0/target0/lun0/part6 1182 19452
146761776
83 Linux
Added Networkcard : 3com 905
Output of lspci and lspci -n:
Both are from knoppix since im not able to boot up in debian and run
lspci
00:00.0 Host bridge: Intel Corp.: Unknown device 2584 (rev 04)
00:01.0 PCI bridge: Intel Corp.: Unknown device 2585 (rev 04)
00:1c.0 PCI bridge: Intel Corp.: Unknown device 2660 (rev 03)
00:1c.1 PCI bridge: Intel Corp.: Unknown device 2662 (rev 03)
00:1d.0 USB Controller: Intel Corp.: Unknown device 2658 (rev 03)
00:1d.1 USB Controller: Intel Corp.: Unknown device 2659 (rev 03)
00:1d.2 USB Controller: Intel Corp.: Unknown device 265a (rev 03)
00:1d.3 USB Controller: Intel Corp.: Unknown device 265b (rev 03)
00:1d.7 USB Controller: Intel Corp.: Unknown device 265c (rev 03)
00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB/EB PCI Bridge (rev d3)
00:1e.2 Multimedia audio controller: Intel Corp.: Unknown device 266e
(rev 03)
00:1f.0 ISA bridge: Intel Corp.: Unknown device 2640 (rev 03)
00:1f.1 IDE interface: Intel Corp.: Unknown device 266f (rev 03)
00:1f.2 IDE interface: Intel Corp.: Unknown device 2652 (rev 03)
00:1f.3 SMBus: Intel Corp.: Unknown device 266a (rev 03)
01:00.0 VGA compatible controller: ATI Technologies Inc: Unknown
device 5b60
01:00.1 Display controller: ATI Technologies Inc: Unknown device 5b70
02:00.0 Ethernet controller: Broadcom Corporation: Unknown device 1677
(rev 01)
04:00.0 FireWire (IEEE 1394): Lucent Microelectronics FW323 (rev 61)
04:02.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado]
(rev 74)
00:00.0 Class 0600: 8086:2584 (rev 04)
00:01.0 Class 0604: 8086:2585 (rev 04)
00:1c.0 Class 0604: 8086:2660 (rev 03)
00:1c.1 Class 0604: 8086:2662 (rev 03)
00:1d.0 Class 0c03: 8086:2658 (rev 03)
00:1d.1 Class 0c03: 8086:2659 (rev 03)
00:1d.2 Class 0c03: 8086:265a (rev 03)
00:1d.3 Class 0c03: 8086:265b (rev 03)
00:1d.7 Class 0c03: 8086:265c (rev 03)
00:1e.0 Class 0604: 8086:244e (rev d3)
00:1e.2 Class 0401: 8086:266e (rev 03)
00:1f.0 Class 0601: 8086:2640 (rev 03)
00:1f.1 Class 0101: 8086:266f (rev 03)
00:1f.2 Class 0101: 8086:2652 (rev 03)
00:1f.3 Class 0c05: 8086:266a (rev 03)
01:00.0 Class 0300: 1002:5b60
01:00.1 Class 0380: 1002:5b70
02:00.0 Class 0200: 14e4:1677 (rev 01)
04:00.0 Class 0c00: 11c1:5811 (rev 61)
04:02.0 Class 0200: 10b7:9200 (rev 74)
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [0]
Configure network HW: [0]
Config network: [0]
Detect CD: [0]
Load installer modules: [0]
Detect hard drives: [E/0] se below
Partition hard drives: [0]
Create file systems: [0]
Mount partitions: [0]
Install base system: [0]
Install boot loader: [0]
Reboot: [E]
Comments/Problems:
As you can se on the Base System Installation Checklist the
installation goes fine pretty much the hole way until reboot after
installation where the kernel stops around Real Time Clock Driver
v1.12. Ive not been able to boot via console to get the full output
from kernel but ive attached the syslog and demsg from the
installation (i got openssh-client up and running in the install)
thanks to Hydroxid from #debian-boot on freenode you guys rock!! :)
Hope this helps and im ofcause available for more info or test or
whatever should it be needed.
/Thomas
Reply to: