Bug#260152: Installation report
Package: installation-reports
INSTALL REPORT
Debian-installer-version: 20040710 netboot CD image
uname -a: Linux damiel 2.4.25-powerpc-small #1 mer avr 14 17:26:11 CEST 2004 ppc GNU/Linux
Date: 20040712
Method: From CD image, no external access.
Machine: 15" Powerbook 1.5GHz
Processor: 1.5GHz G4
Memory: 512M
Root Device: /dev/hda3
Root Size/partition table:
rootfs / rootfs rw 0 0
/dev2/root2 / ext3 rw 0 0
proc /proc proc rw 0 0
devpts /dev/pts devpts rw 0 0
tmpfs /dev/shm tmpfs rw 0 0
usbfs /proc/bus/usb usbfs rw 0 0
Output of lspci and lspci -n:
0000:00:0b.0 Host bridge: Apple Computer Inc. UniNorth 2 AGP
0000:00:10.0 VGA compatible controller: ATI Technologies Inc RV350 [Mobility Radeon 9600 M10]
0000:10:0b.0 Host bridge: Apple Computer Inc. UniNorth 2 PCI
0000:10:12.0 Network controller: Broadcom Corporation BCM94306 802.11g (rev 03)
0000:10:13.0 CardBus bridge: Texas Instruments PCI1510 PC card Cardbus Controller
0000:10:17.0 Class ff00: Apple Computer Inc. KeyLargo/Intrepid Mac I/O
0000:10:18.0 USB Controller: Apple Computer Inc. KeyLargo/Intrepid USB
0000:10:19.0 USB Controller: Apple Computer Inc. KeyLargo/Intrepid USB
0000:10:1a.0 USB Controller: Apple Computer Inc. KeyLargo/Intrepid USB
0000:10:1b.0 USB Controller: NEC Corporation USB (rev 43)
0000:10:1b.1 USB Controller: NEC Corporation USB (rev 43)
0000:10:1b.2 USB Controller: NEC Corporation USB 2.0 (rev 04)
0000:24:0b.0 Host bridge: Apple Computer Inc. UniNorth 2 Internal PCI
0000:24:0d.0 Class ff00: Apple Computer Inc. UniNorth/Intrepid ATA/100
0000:24:0e.0 FireWire (IEEE 1394): Apple Computer Inc. UniNorth 2 FireWire (rev 81)
0000:24:0f.0 Class ffff: Apple Computer Inc. UniNorth 2 GMAC (Sun GEM) (rev ff)
0000:00:0b.0 Class 0600: 106b:0034
0000:00:10.0 Class 0300: 1002:4e50
0000:10:0b.0 Class 0600: 106b:0035
0000:10:12.0 Class 0280: 14e4:4320 (rev 03)
0000:10:13.0 Class 0607: 104c:ac56
0000:10:17.0 Class ff00: 106b:003e
0000:10:18.0 Class 0c03: 106b:003f
0000:10:19.0 Class 0c03: 106b:003f
0000:10:1a.0 Class 0c03: 106b:003f
0000:10:1b.0 Class 0c03: 1033:0035 (rev 43)
0000:10:1b.1 Class 0c03: 1033:0035 (rev 43)
0000:10:1b.2 Class 0c03: 1033:00e0 (rev 04)
0000:24:0b.0 Class 0600: 106b:0036
0000:24:0d.0 Class ff00: 106b:003b
0000:24:0e.0 Class 0c00: 106b:0031 (rev 81)
0000:24:0f.0 Class ffff: 106b:0032 (rev ff)
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [O]
Configure network HW: [ ]
Config network: [E]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Create file systems: [O]
Mount partitions: [O]
Install base system: [O]
Install boot loader: [O]
Reboot: [O]
Comments/Problems:
Install was pretty flawless, including detection of MacOS X. It was a small
wart for the installer to prompt me for an IP address in this disconnected
install (it appeared to correctly skip DHCP, presumably using the link state).
It is vagely surprising that despite selecting a 2.6 based install I've ended
up with a 2.4 kernel installed. This is hardly the end of the world, though.
Since this is a CD-only install without network access I have not configured X.
It would have been nice for the installer to allow me to configure network
sources, even while unable to access the network.
Reply to: