Bug#250740: /etc/network/interfaces didn't include eth0
Package: installation-reports
INSTALL REPORT
Debian-installer-version:
http://cdimage.debian.org/pub/cdimage-testing/sid_d-i/i386/20040523/sarge-i386-netinst.iso
uname -a: Linux roller.fmi.uni-sofia.bg 2.4.26-1-386 #2 Sat May 1
16:31:24 EST 2004 i686 GNU/Linux
Date: 2004-05-24
Method: netinst.iso
Machine:
Processor: Pentium III 2x933
Memory: 256M
Root Device: IDE, 30G
Root Size/partition table: / on 20G, swap on 512M
Output of lspci and lspci -n:
0000:00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo
PRO133x] (rev c4)
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo
MVP3/Pro133x AGP]
0000:00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super
South] (rev 40)
0000:00:07.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C/VT8235 PIPC Bus Master IDE (rev 06)
0000:00:07.2 USB Controller: VIA Technologies, Inc. VT6202 [USB 2.0
controller] (rev 16)
0000:00:07.3 USB Controller: VIA Technologies, Inc. VT6202 [USB 2.0
controller] (rev 16)
0000:00:07.4 SMBus: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
(rev 40)
0000:00:0b.0 Multimedia audio controller: C-Media Electronics Inc CM8738
(rev 10)
0000:00:0c.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
0000:01:00.0 VGA compatible controller: ATI Technologies Inc Radeon
RV100 QY [Radeon 7000/VE]
0000:00:00.0 Class 0600: 1106:0691 (rev c4)
0000:00:01.0 Class 0604: 1106:8598
0000:00:07.0 Class 0601: 1106:0686 (rev 40)
0000:00:07.1 Class 0101: 1106:0571 (rev 06)
0000:00:07.2 Class 0c03: 1106:3038 (rev 16)
0000:00:07.3 Class 0c03: 1106:3038 (rev 16)
0000:00:07.4 Class 0c05: 1106:3057 (rev 40)
0000:00:0b.0 Class 0401: 13f6:0111 (rev 10)
0000:00:0c.0 Class 0200: 10ec:8139 (rev 10)
0000:01:00.0 Class 0300: 1002:5159
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [O]
Configure network HW: [O]
Config network: [O]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Create file systems: [O]
Mount partitions: [O]
Install base system: [O]
Install boot loader: [O]
Reboot: [O]
Comments/Problems:
There was one problem. My network card (RealTek 8139C) was recognized
during 1st stage (module 8139too is loaded), I entered IP, etc.
ifconfig showed configured eth0. After reboot module 8139too was loaded
but eth0 was not configured. There wasn't any configuration for eth0 in
/etc/network/interfaces. There was configuration only for lo.
Install logs and other status info is available in
/var/log/debian-installer/.
Once you have filled out this report, mail it to submit@bugs.debian.org.
Reply to: