Bug#249024: boot-floppy: cdrom SAMSUNG SC-140B not recognize by beta4
Martin Michlmayr <tbm@cyrius.com> writes:
> * Arnaud Vandyck <avdyk@debian.org> [2004-05-14 16:14]:
>> I teach about Linux on Monday and made some tests with Knoppix. K3.4
>> has the same problem, but K3.3 boots ok.
>
> Can you show the kernel output (dmesg) from a working Knoppix 3.3?
> Can you show the output from beta4? What kernel does Knoppix 3.3 and
> 3.4 use?
Attached are dmesg from knoppix 3.3 and d-i beta4; I think knoppix 3.3
and 3.4 both use kernel 2.4 as default kernels.
--
Arnaud Vandyck
I'm personally quite happy with one stable release every two years, and
am of the opinion that trying to release more will mean we'll have to
rename the distro from "stable" to "wobbly".
-- Scott James Remnant on debian-devel
Linux version 2.4.24-xfs (root@Knoppix) (gcc version 2.95.4 20011002 (Debian prerelease)) #1 SMP Mi Feb 4 01:03:50 CET 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000018000000 (usable)
BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
384MB LOWMEM available.
On node 0 totalpages: 98304
zone(0): 4096 pages.
zone(1): 94208 pages.
zone(2): 0 pages.
ACPI disabled because your bios is from 99 and too old
You can enable it with acpi=force
Kernel command line: auto BOOT_IMAGE=Linux ro root=302 ramdisk_size=100000 init=/etc/init lang=us apm=power-off hda=scsi hdb=scsi hdc=scsi hdd=scsi hde=scsi hdf=scsi hdg=scsi hdh=scsi nomce quiet lang=be
ide_setup: hda=scsi
ide_setup: hdb=scsi
ide_setup: hdc=scsi
ide_setup: hdd=scsi
ide_setup: hde=scsi
ide_setup: hdf=scsi
ide_setup: hdg=scsi
ide_setup: hdh=scsi
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
Detected 448.880 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 894.56 BogoMIPS
Memory: 385604k/393216k available (1278k kernel code, 7228k reserved, 547k data, 136k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU0: Intel Pentium III (Katmai) stepping 02
per-CPU timeslice cutoff: 1464.52 usecs.
SMP motherboard not detected.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 448.8636 MHz.
..... host bus clock speed is 99.7473 MHz.
cpu: 0, clocks: 997473, slice: 498736
CPU0<T0:997472,T1:498736,D:0,S:498736,C:997473>
Waiting on wait_init_idle (map = 0x0)
All processors have done init_idle
PCI: PCI BIOS revision 2.10 entry at 0xfcaee, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router PIIX/ICH [8086/7110] at 00:07.0
Limiting direct PCI/PCI transfers.
isapnp: Scanning for PnP cards...
isapnp: Card 'CS4236B'
isapnp: 1 Plug & Play card detected total
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
vesafb: framebuffer at 0xfd000000, mapped to 0xd880d000, size 3072k
vesafb: mode is 1024x768x16, linelength=2048, pages=1
vesafb: protected mode interface info at c000:4ac6
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 00:07.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
hda: Maxtor 90432D3, ATA DISK drive
hdc: SAMSUNG SC-140B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 8440992 sectors (4322 MB) w/256KiB Cache, CHS=525/255/63
ide-cd: passing drive hdc to ide-scsi emulation.
hdc: attached ide-scsi driver.
Partition check:
hda: hda1 hda2
ide: late registration of driver.
Promise Fasttrak(tm) Softwareraid driver 0.03beta: No raid array found
Highpoint HPT370 Softwareraid driver for linux version 0.02
Guestimating sector 8439967 for superblock
driver for Silicon Image(tm) Medley(tm) hardware version 0.0.1: No raid array found
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: SAMSUNG Model: CD-ROM SC-140B Rev: d003
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 40x/40x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 143k freed
VFS: Mounted root (ext2 filesystem).
Journalled Block Device driver loaded
(recovery.c, 256): journal_recover: JBD: recovery, exit status 0, recovered transactions 722 to 773
(recovery.c, 258): journal_recover: JBD: Replayed 2026 and revoked 0/6 blocks
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal journal
ext3_orphan_cleanup: deleting unreferenced inode 133377
EXT3-fs: ide0(3,2): 1 orphan inode deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 136k freed
Real Time Clock Driver v1.10e
Adding Swap: 489940k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal journal
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
Intel ISA PCIC probe: not found.
Databook TCIC-2 PCMCIA probe: not found.
unloading Kernel Card Services
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 01:17:44 Feb 4 2004
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 11 for device 00:07.2
usb-uhci.c: USB UHCI at I/O 0xdce0, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usbdevfs: remount parameter error
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
PCI: Found IRQ 10 for device 00:0d.0
PCI: Sharing IRQ 10 with 01:00.0
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
See Documentation/networking/vortex.txt
00:0d.0: 3Com PCI 3c900 Cyclone 10Mbps TPC at 0xdc00. Vers LK1.1.18-ac
00:50:04:3a:3b:39, IRQ 10
product code 5355 rev 00.4 date 03-29-99
Internal config register is 1800000, transceivers 0x18.
8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
MII transceiver found at address 24, status 182d.
Enabling bus-master transmits and whole-frame receives.
00:0d.0: scatter/gather enabled. h/w checksums enabled
ad1848/cs4248 codec driver Copyright (C) by Hannu Savolainen 1993-1996
ad1848: WSS/SB detected
ad1848: ISAPnP reports 'WSS/SB' at i/o 0x534, irq 5, dma 1, 3
cs4232: set synthio and synthirq to use the wavefront facilities.
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 322M
agpgart: Detected Intel 440BX chipset
agpgart: AGP aperture is 64M @ 0xf4000000
Linux version 2.4.26-1-386 (herbert@gondolin) (gcc version 3.3.3 (Debian 20040401)) #2 Sat May 1 16:31:24 EST 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000018000000 (usable)
BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
384MB LOWMEM available.
On node 0 totalpages: 98304
zone(0): 4096 pages.
zone(1): 94208 pages.
zone(2): 0 pages.
ACPI disabled because your bios is from 99 and too old
You can enable it with acpi=force
Kernel command line: vga=normal initrd=/install/initrd.gz ramdisk_size=10240 root=/dev/rd/0 init=/linuxrc devfs=mount,dall rw BOOT_IMAGE=/install/vmlinuz
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
Detected 448.883 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 894.56 BogoMIPS
Memory: 383880k/393216k available (1080k kernel code, 8952k reserved, 466k data, 92k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU: Intel Pentium III (Katmai) stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 448.8921 MHz.
..... host bus clock speed is 99.7536 MHz.
cpu: 0, clocks: 997536, slice: 498768
CPU0<T0:997536,T1:498768,D:0,S:498768,C:997536>
ACPI: Subsystem revision 20040326
ACPI: Interpreter disabled.
PCI: PCI BIOS revision 2.10 entry at 0xfcaee, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: ACPI tables contain no PCI IRQ routing entries
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router PIIX/ICH [8086/7110] at 00:07.0
Limiting direct PCI/PCI transfers.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
COMX: driver version 0.85 (C) 1995-1999 ITConsult-Pro Co. <info@itc.hu>
RAMDISK driver initialized: 16 RAM disks of 10240K size 1024 blocksize
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 2779k freed
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
VFS: Mounted root (ext2 filesystem).
Trying to move old root to /initrd ... okay
Mounted devfs on /dev
Freeing unused kernel memory: 92k freed
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
vga16fb: initializing
vga16fb: mapped to 0xc00a0000
Console: switching to colour frame buffer device 80x30
fb0: VGA16 VGA frame buffer device
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 16:13:08 May 1 2004
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 11 for device 00:07.2
usb-uhci.c: USB UHCI at I/O 0xdce0, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb.c: registered new driver usbkbd
usbkbd.c: :USB HID Boot Protocol keyboard driver
usb.c: registered new driver serial
usbserial.c: USB Serial support registered for Generic
usbserial.c: USB Serial Driver core v1.4
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SCSI subsystem driver Revision: 1.00
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
inserting floppy driver for 2.4.26-1-386
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
ide: late registration of driver.
PIIX4: IDE controller at PCI slot 00:07.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
hda: Maxtor 90432D3, ATA DISK drive
blk: queue d8854300, I/O limit 4095Mb (mask 0xffffffff)
hdc: SAMSUNG SC-140B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: 8440992 sectors (4322 MB) w/256KiB Cache, CHS=8374/16/63, UDMA(33)
Partition check:
/dev/ide/host0/bus0/target0/lun0: [PTBL] [525/255/63] p1 p2
hdc: attached ide-cdrom driver.
hdc: ATAPI 40X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
isapnp: Scanning for PnP cards...
isapnp: Card 'CS4236B'
isapnp: 1 Plug & Play card detected total
Intel ISA PCIC probe: not found.
Intel ISA PCIC probe: not found.
ISO 9660 Extensions: Microsoft Joliet Level 3
hdc: media error (bad sector): status=0x51 { DriveReady SeekComplete Error }
hdc: media error (bad sector): error=0x34
end_request: I/O error, dev 16:00 (hdc), sector 132
ISOFS: unable to read i-node block
ISOFS: changing to secondary root
hdc: media error (bad sector): status=0x51 { DriveReady SeekComplete Error }
hdc: media error (bad sector): error=0x34
end_request: I/O error, dev 16:00 (hdc), sector 1280
ISOFS: unable to read i-node block
VFS: Can't find ext2 filesystem on dev fd(2,0).
cramfs: wrong magic
Unable to identify CD-ROM format.
VFS: Can't find ext2 filesystem on dev fd(2,0).
cramfs: wrong magic
Unable to identify CD-ROM format.
ISO 9660 Extensions: Microsoft Joliet Level 3
hdc: media error (bad sector): status=0x51 { DriveReady SeekComplete Error }
hdc: media error (bad sector): error=0x34
end_request: I/O error, dev 16:00 (hdc), sector 132
ISOFS: unable to read i-node block
ISOFS: changing to secondary root
hdc: media error (bad sector): status=0x51 { DriveReady SeekComplete Error }
hdc: media error (bad sector): error=0x34
end_request: I/O error, dev 16:00 (hdc), sector 1280
ISOFS: unable to read i-node block
EXT2-fs warning (device ide0(3,2)): ext2_read_super: mounting ext3 filesystem as ext2
Reply to: