Installation report
INSTALL REPORT
Debian-installer-version: Jan 1st netinst from ~manty
Method: Boot from CD-ROM, network install from debian.yorku.ca
Machine: IBM Thinkpad A31p (2653-H5U)
Processor: Intel(R) Pentium(R) 4 Mobile CPU 1.70GHz
Memory: 512MB
Root Device: HITACHI_DK23FB-60B, ATA DISK drive
Root Size/partition table:
Name Mount point FS Type Size (MB)
hda1 n/a NTFS 20003.89
hda2 / ext3 998.65
hda3 n/a LVM 38490.44
hda4 n/a swap 518.68
Output of lspci:
00:00.0 Host bridge: Intel Corp. 82845 845 (Brookdale) Chipset Host
Bridge (rev 04)
00:01.0 PCI bridge: Intel Corp. 82845 845 (Brookdale) Chipset AGP
Bridge (rev 04)
00:1d.0 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #1) (rev 02)
00:1d.1 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #2) (rev 02)
00:1d.2 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #3) (rev 02)
00:1e.0 PCI bridge: Intel Corp. 82801BAM/CAM PCI Bridge (rev 42)
00:1f.0 ISA bridge: Intel Corp. 82801CAM ISA Bridge (LPC) (rev 02)
00:1f.1 IDE interface: Intel Corp. 82801CAM IDE U100 (rev 02)
00:1f.3 SMBus: Intel Corp. 82801CA/CAM SMBus Controller (rev 02)
00:1f.5 Multimedia audio controller: Intel Corp. 82801CA/CAM AC'97
Audio Controller (rev 02)
00:1f.6 Modem: Intel Corp. 82801CA/CAM AC'97 Modem Controller (rev 02)
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon RV200
LX [Mobility FireGL 7800 M7]
02:00.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev a8)
02:00.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev a8)
02:00.2 FireWire (IEEE 1394): Ricoh Co Ltd R5C552 IEEE 1394 Controller
02:02.0 Network controller: Harris Semiconductor Prism 2.5 Wavelan
chipset (rev 01)
02:08.0 Ethernet controller: Intel Corp. 82801CAM (ICH3) PRO/100 VE
(LOM) Ethernet Controller (rev 42)
Base System Installation Checklist:
Initial boot worked: [o]
Configure network HW: [o]
Config network: [o]
Detect CD: [o]
Load installer modules: [o]
Detect hard drives: [o]
Partition hard drives: [o]
Create file systems: [o]
Mount partitions: [o]
Install base system: [o]
Install boot loader: [o]
Reboot: [e]
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Reboot error:
During the installation, the wireless network card was eth0 and the
ethernet card was eth1. When I rebooted, the wireless card became eth1
and the ethernet card eth0.
Comments:
It would have been nice if LILO had been configured so that one boot
menu choice would be hda1, a Windows partition.
The installer allowed me to label hda3 as an LVM partition, but I did
not manage to create a volume group or logical volumes.
Thank you for developing Debian.
Kristjan Onu
Reply to: