linux-image-4.19.0-0.bpo.6-amd64: xHCI host controller not responding, assume dead after resume
Package: src:linux
Version: 4.19.67-2+deb10u1~bpo9+1
Severity: normal
Dear Maintainer,
after a hibernate / resume cycle, sometimes devices attached to the front USB
ports are no longer recognized.
This did not occur with the vmlinuz-4.19.0-0.bpo.5-amd64 kernel.
An unbind / bind seems to fix the issue.
echo -n 0000:02:00.0 > /sys/bus/pci/drivers/xhci_hcd/unbind
sleep 5
echo -n 0000:02:00.0 > /sys/bus/pci/drivers/xhci_hcd/bind
[98961.977381] xhci_hcd 0000:02:00.0: Host halt failed, -110
[98961.977386] xhci_hcd 0000:02:00.0: Host controller not halted, aborting reset.
[98972.071151] xhci_hcd 0000:02:00.0: Abort failed to stop command ring: -110
[98972.087177] xhci_hcd 0000:02:00.0: Host halt failed, -110
[98972.087181] xhci_hcd 0000:02:00.0: xHCI host controller not responding, assume dead
[98972.087189] xhci_hcd 0000:02:00.0: HC died; cleaning up
[112226.844579] xhci_hcd 0000:02:00.0: remove, state 4
[112226.845138] xhci_hcd 0000:02:00.0: USB bus 4 deregistered
[112226.845152] xhci_hcd 0000:02:00.0: remove, state 4
[112226.960470] xhci_hcd 0000:02:00.0: USB bus 2 deregistered
[112231.963278] xhci_hcd 0000:02:00.0: xHCI Host Controller
[112231.963298] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 2
[112232.068145] xhci_hcd 0000:02:00.0: hcc params 0x014042cb hci version 0x96 quirks 0x0000000000000004
[112232.068731] xhci_hcd 0000:02:00.0: xHCI Host Controller
[112232.068734] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 4
[112232.068737] xhci_hcd 0000:02:00.0: Host supports USB 3.0 SuperSpeed
[112232.404260] usb 4-2: new SuperSpeed Gen 1 USB device number 2 using xhci_hcd
Thanks,
Stefan
-- Package-specific info:
** Version:
Linux version 4.19.0-0.bpo.6-amd64 (debian-kernel@lists.debian.org) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 SMP Debian 4.19.67-2+deb10u1~bpo9+1 (2019-09-30)
** Command line:
BOOT_IMAGE=/vmlinuz-4.19.0-0.bpo.6-amd64 root=/dev/mapper/sys-root ro quiet resume=/dev/mapper/sys-swap
** Not tainted
** Kernel log:
[108563.756298] PM: Need to copy 275631 pages
[108563.756305] PM: Normal pages needed: 275631 + 1024, available pages: 2725245
[108563.127284] PM: Restoring platform NVS memory
[108563.128775] Enabling non-boot CPUs ...
[108563.128868] x86: Booting SMP configuration:
[108563.128871] smpboot: Booting Node 0 Processor 1 APIC 0x2
[108563.132037] cache: parent cpu1 should not be sleeping
[108563.132494] CPU1 is up
[108563.132551] smpboot: Booting Node 0 Processor 2 APIC 0x1
[108563.135744] cache: parent cpu2 should not be sleeping
[108563.136611] CPU2 is up
[108563.136673] smpboot: Booting Node 0 Processor 3 APIC 0x3
[108563.139792] cache: parent cpu3 should not be sleeping
[108563.140312] CPU3 is up
[108563.148788] ACPI: Waking up from system sleep state S4
[108563.223341] usb usb1: root hub lost power or was reset
[108563.223429] usb usb3: root hub lost power or was reset
[108563.227242] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[108563.227334] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[108563.233990] sd 0:0:0:0: [sda] Starting disk
[108563.557051] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[108563.557114] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[108563.559558] ata1.00: configured for UDMA/133
[108563.570261] usb 1-1: reset high-speed USB device number 2 using ehci-pci
[108563.582287] usb 3-1: reset high-speed USB device number 2 using ehci-pci
[108563.593417] ata2.00: configured for UDMA/100
[108564.034330] usb 3-1.4: reset full-speed USB device number 3 using ehci-pci
[108564.350334] usb 3-1.5: reset full-speed USB device number 4 using ehci-pci
[108564.942342] usb 3-1.5.1: reset low-speed USB device number 5 using ehci-pci
[108565.506326] usb 3-1.5.3: reset low-speed USB device number 6 using ehci-pci
[108565.845938] Restarting kernel threads ... done.
[108565.846925] PM: Basic memory bitmaps freed
[108565.846926] OOM killer enabled.
[108565.846926] Restarting tasks ... done.
[108565.848870] video LNXVIDEO:00: Restoring backlight state
[108571.158639] device eth0 entered promiscuous mode
[108571.163602] br0: port 1(eth0.5) entered blocking state
[108571.163607] br0: port 1(eth0.5) entered disabled state
[108571.163777] device eth0.5 entered promiscuous mode
[108571.171246] IPv6: ADDRCONF(NETDEV_UP): br0: link is not ready
[108574.653802] IPv6: ADDRCONF(NETDEV_UP): eth0.4: link is not ready
[108574.696153] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[108574.696254] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.4: link becomes ready
[108574.696311] br0: port 1(eth0.5) entered blocking state
[108574.696312] br0: port 1(eth0.5) entered forwarding state
[108574.696355] br1: port 1(eth0.6) entered blocking state
[108574.696356] br1: port 1(eth0.6) entered forwarding state
[108574.696394] IPv6: ADDRCONF(NETDEV_CHANGE): br0: link becomes ready
[109052.103337] systemd-logind[3371]: New session 643 of user bd.
[110464.978835] systemd-logind[3371]: New session c8 of user nobody.
[110464.995754] systemd-logind[3371]: New session c9 of user nobody.
[110465.009706] systemd-logind[3371]: New session c10 of user nobody.
[112226.844579] xhci_hcd 0000:02:00.0: remove, state 4
[112226.844597] usb usb4: USB disconnect, device number 1
[112226.845138] xhci_hcd 0000:02:00.0: USB bus 4 deregistered
[112226.845152] xhci_hcd 0000:02:00.0: remove, state 4
[112226.845160] usb usb2: USB disconnect, device number 1
[112226.960470] xhci_hcd 0000:02:00.0: USB bus 2 deregistered
[112231.963278] xhci_hcd 0000:02:00.0: xHCI Host Controller
[112231.963298] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 2
[112232.068145] xhci_hcd 0000:02:00.0: hcc params 0x014042cb hci version 0x96 quirks 0x0000000000000004
[112232.068412] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[112232.068413] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[112232.068414] usb usb2: Product: xHCI Host Controller
[112232.068415] usb usb2: Manufacturer: Linux 4.19.0-0.bpo.6-amd64 xhci-hcd
[112232.068416] usb usb2: SerialNumber: 0000:02:00.0
[112232.068571] hub 2-0:1.0: USB hub found
[112232.068584] hub 2-0:1.0: 2 ports detected
[112232.068731] xhci_hcd 0000:02:00.0: xHCI Host Controller
[112232.068734] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 4
[112232.068737] xhci_hcd 0000:02:00.0: Host supports USB 3.0 SuperSpeed
[112232.071497] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[112232.071537] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 4.19
[112232.071538] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[112232.071539] usb usb4: Product: xHCI Host Controller
[112232.071539] usb usb4: Manufacturer: Linux 4.19.0-0.bpo.6-amd64 xhci-hcd
[112232.071540] usb usb4: SerialNumber: 0000:02:00.0
[112232.071652] hub 4-0:1.0: USB hub found
[112232.071665] hub 4-0:1.0: 2 ports detected
[112232.404260] usb 4-2: new SuperSpeed Gen 1 USB device number 2 using xhci_hcd
[112232.428289] usb 4-2: New USB device found, idVendor=152d, idProduct=0567, bcdDevice=92.02
[112232.428294] usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[112232.428296] usb 4-2: Product: USB to ATA/ATAPI Bridge
[112232.428299] usb 4-2: Manufacturer: JMicron
[112232.428301] usb 4-2: SerialNumber: 0123456789ABCDEF
[112232.430250] usb 4-2: UAS is blacklisted for this device, using usb-storage instead
[112232.430254] usb-storage 4-2:1.0: USB Mass Storage device detected
[112232.430361] usb-storage 4-2:1.0: Quirks match for vid 152d pid 0567: 1800000
[112232.430424] scsi host6: usb-storage 4-2:1.0
[112233.436981] scsi 6:0:0:0: Direct-Access JMicron Generic 9202 PQ: 0 ANSI: 6
[112233.437649] sd 6:0:0:0: Attached scsi generic sg2 type 0
[112238.578470] sd 6:0:0:0: [sdb] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[112238.578903] sd 6:0:0:0: [sdb] Write Protect is off
[112238.578908] sd 6:0:0:0: [sdb] Mode Sense: 33 00 00 08
[112238.579446] sd 6:0:0:0: [sdb] No Caching mode page found
[112238.579464] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[112238.609299] sd 6:0:0:0: [sdb] Attached SCSI disk
[112262.739099] XFS (dm-31): Mounting V4 Filesystem
[112262.944243] XFS (dm-31): Ending clean mount
[112390.338958] XFS (dm-31): Unmounting Filesystem
** Model information
sys_vendor: FUJITSU
product_name: ESPRIMO Q900
product_version:
chassis_vendor: AOpen Inc.
chassis_version: MPC-D1009
bios_vendor: American Megatrends Inc.
bios_version: 1.05.1009
board_vendor: AOpen Inc.
board_name: D1009
board_version: A1A3
** Loaded modules:
algif_skcipher
af_alg
uas
usb_storage
xt_NFLOG
ipt_REJECT
nf_reject_ipv4
xt_conntrack
iptable_filter
ipt_MASQUERADE
xt_nat
xt_REDIRECT
xt_tcpudp
iptable_nat
nf_nat_ipv4
nf_nat
nf_conntrack
nf_defrag_ipv6
nf_defrag_ipv4
ip_tables
x_tables
nfnetlink_log
nfnetlink
autofs4
binfmt_misc
fuse
nfsd
auth_rpcgss
nfs_acl
nfs
lockd
grace
fscache
sunrpc
bridge
ext4
crc16
mbcache
jbd2
fscrypto
ecb
f71882fg
hwmon_vid
8021q
garp
stp
mrp
llc
loop
parport_pc
ppdev
lp
parport
dm_crypt
intel_rapl
x86_pkg_temp_thermal
intel_powerclamp
coretemp
arc4
kvm_intel
iwldvm
kvm
mac80211
irqbypass
crct10dif_pclmul
crc32_pclmul
ghash_clmulni_intel
snd_hda_codec_hdmi
intel_cstate
snd_hda_codec_realtek
intel_uncore
snd_hda_codec_generic
iTCO_wdt
intel_rapl_perf
mei_wdt
iTCO_vendor_support
iwlwifi
tpm_infineon
i915
snd_usb_audio
snd_hda_intel
snd_hda_codec
snd_usbmidi_lib
snd_rawmidi
snd_hda_core
snd_hwdep
snd_seq_device
snd_pcm
snd_timer
drm_kms_helper
pcspkr
snd
cfg80211
drm
wmi
joydev
evdev
i2c_algo_bit
soundcore
tpm_tis
tpm_tis_core
tpm
sg
mei_me
mei
rng_core
rfkill
pcc_cpufreq
lpc_ich
video
button
xfs
raid10
raid456
async_raid6_recov
async_memcpy
async_pq
async_xor
async_tx
xor
raid6_pq
libcrc32c
crc32c_generic
raid1
raid0
multipath
linear
md_mod
hid_generic
usbhid
hid
dm_mod
sr_mod
cdrom
sd_mod
crc32c_intel
xhci_pci
xhci_hcd
ehci_pci
aesni_intel
ehci_hcd
ahci
libahci
libata
e1000e
usbcore
aes_x86_64
scsi_mod
crypto_simd
cryptd
glue_helper
i2c_i801
usb_common
thermal
fan
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0104] (rev 09)
Subsystem: AOPEN Inc. 2nd Generation Core Processor Family DRAM Controller [a0a0:0809]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0126] (rev 09) (prog-if 00 [VGA controller])
Subsystem: AOPEN Inc. 2nd Generation Core Processor Family Integrated Graphics Controller [a0a0:0809]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 34
Region 0: Memory at f7800000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at c0000000 (64-bit, prefetchable) [size=512M]
Region 4: I/O ports at f000 [size=64]
[virtual] Expansion ROM at 000c0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: i915
Kernel modules: i915
00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 [8086:1c3a] (rev 04)
Subsystem: AOPEN Inc. 6 Series/C200 Series Chipset Family MEI Controller [a0a0:0809]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 26
Region 0: Memory at f7e2b000 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
Kernel driver in use: mei_me
Kernel modules: mei_me
00:19.0 Ethernet controller [0200]: Intel Corporation 82579LM Gigabit Network Connection [8086:1502] (rev 05)
Subsystem: AOPEN Inc. 82579LM Gigabit Network Connection [a0a0:0809]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 36
Region 0: Memory at f7e00000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at f7e29000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at f080 [size=32]
Capabilities: <access denied>
Kernel driver in use: e1000e
Kernel modules: e1000e
00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 05) (prog-if 20 [EHCI])
Subsystem: AOPEN Inc. 6 Series/C200 Series Chipset Family USB Enhanced Host Controller [a0a0:0809]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f7e28000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller [8086:1c20] (rev 05)
Subsystem: AOPEN Inc. 6 Series/C200 Series Chipset Family High Definition Audio Controller [a0a0:0809]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 33
Region 0: Memory at f7e20000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 [8086:1c10] (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: f7d00000-f7dfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.4 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 [8086:1c18] (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Memory behind bridge: f7c00000-f7cfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 [8086:1c26] (rev 05) (prog-if 20 [EHCI])
Subsystem: AOPEN Inc. 6 Series/C200 Series Chipset Family USB Enhanced Host Controller [a0a0:0809]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f7e27000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
00:1f.0 ISA bridge [0601]: Intel Corporation QM67 Express Chipset Family LPC Controller [8086:1c4f] (rev 05)
Subsystem: AOPEN Inc. QM67 Express Chipset Family LPC Controller [a0a0:0809]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
Kernel modules: lpc_ich
00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller [8086:1c03] (rev 05) (prog-if 01 [AHCI 1.0])
Subsystem: AOPEN Inc. 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller [a0a0:0809]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 27
Region 0: I/O ports at f0d0 [size=8]
Region 1: I/O ports at f0c0 [size=4]
Region 2: I/O ports at f0b0 [size=8]
Region 3: I/O ports at f0a0 [size=4]
Region 4: I/O ports at f060 [size=32]
Region 5: Memory at f7e26000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller [8086:1c22] (rev 05)
Subsystem: AOPEN Inc. 6 Series/C200 Series Chipset Family SMBus Controller [a0a0:0809]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f7e25000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at f040 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c_i801
01:00.0 Network controller [0280]: Intel Corporation Centrino Advanced-N 6205 [Taylor Peak] [8086:0082] (rev 34)
Subsystem: Intel Corporation Centrino Advanced-N 6205 AGN [8086:1301]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 35
Region 0: Memory at f7d00000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: iwlwifi
Kernel modules: iwlwifi
02:00.0 USB controller [0c03]: NEC Corporation uPD720200 USB 3.0 Host Controller [1033:0194] (rev 03) (prog-if 30 [XHCI])
Subsystem: AOPEN Inc. uPD720200 USB 3.0 Host Controller [a0a0:0809]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f7c00000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
** USB devices:
Bus 003 Device 006: ID 045e:077d Microsoft Corp.
Bus 003 Device 005: ID 413c:2011 Dell Computer Corp. Multimedia Pro Keyboard
Bus 003 Device 004: ID 413c:1005 Dell Computer Corp. Multimedia Pro Keyboard Hub
Bus 003 Device 003: ID 413c:a503 Dell Computer Corp.
Bus 003 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 002: ID 152d:0567 JMicron Technology Corp. / JMicron USA Technology Corp. JMS567 SATA 6Gb/s bridge
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: 9.11
APT prefers oldstable-updates
APT policy: (500, 'oldstable-updates'), (500, 'oldstable-debug'), (500, 'oldstable')
Architecture: amd64 (x86_64)
Foreign Architectures: i386
Kernel: Linux 4.19.0-0.bpo.6-amd64 (SMP w/4 CPU cores)
Locale: LANG=en_US.utf8, LC_CTYPE=en_US.utf8 (charmap=UTF-8), LANGUAGE=en_US:en (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: sysvinit (via /sbin/init)
Versions of packages linux-image-4.19.0-0.bpo.6-amd64 depends on:
ii initramfs-tools [linux-initramfs-tool] 0.130
ii kmod 23-2
ii linux-base 4.5
Versions of packages linux-image-4.19.0-0.bpo.6-amd64 recommends:
pn apparmor <none>
ii firmware-linux-free 3.4
Versions of packages linux-image-4.19.0-0.bpo.6-amd64 suggests:
pn debian-kernel-handbook <none>
ii extlinux 3:6.03+dfsg-14.1+deb9u1
ii grub-pc 2.02~beta3-5+deb9u2
pn linux-doc-4.19 <none>
Versions of packages linux-image-4.19.0-0.bpo.6-amd64 is related to:
ii firmware-amd-graphics 20161130-5
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-cavium <none>
pn firmware-intel-sound <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
ii firmware-iwlwifi 20161130-5
pn firmware-libertas <none>
ii firmware-linux-nonfree 20161130-5
ii firmware-misc-nonfree 20161130-5
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
ii firmware-realtek 20161130-5
pn firmware-samsung <none>
pn firmware-siano <none>
pn firmware-ti-connectivity <none>
pn xen-hypervisor <none>
-- no debconf information
Reply to: