Re: Gigabyte MP30-AR1
On 13/09/2016 09:17, wrote:
lsorense@csclub.uwaterloo.ca wrote:
On Mon, Sep 12, 2016 at 05:47:34PM +0100, Phil Endecott wrote:
(BTW, note "EFI v2.40 by American Megatrends". I think that the people
who've installed UEFI on their MP30-AR0 boards (which shipped with only
U-Boot) have installed the open-source TianoCore. This is presumably
something different. Its predominant characteristic for me is how
extraordinarily slow it is; it takes 3 minutes from powering on to
showing the Gigabyte logo, and another minute to show a boot logo.
It's
as if it's interpreting x86 code, or running from a serial ROM, or
something.)
For a server that isn't that unusual. They often run very extensive
power on diagnostics. I think one of the IBM power servers I have dealt
with took 2 minutes from connecting power before you could even press
the power button, and then it took several minutes before the firmware
interface appeared after you hit the button. x86 servers often take
several minutes too.
The output on the serial port doesn't look like it's doing self-tests;
mostly it seems to be loading its own modules, which often have DEBUG
in their names. And that's all after the BMC has booted. I'm curious
to know what MP30-AR0 users see.
I've corrected the blank subject.
Here is the serial output from my MP30-AR0 to the point of reaching the
grub screen. If you want kernel output, let me know.
#############
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2016.09.13 09:20:38
=~=~=~=~=~=~=~=~=~=~=~=
U-Boot 2013.04-mp30ar0_sw_1.18.04 (Sep 02 2015 - 16:38:06) REV: F06b (
uart0 )
CPU0: APM ARM 64-bit Potenza Rev B0 2400MHz PCP 2400MHz
32 KB ICACHE, 32 KB DCACHE
SOC 2000MHz IOBAXI 400MHz AXI 250MHz AHB 200MHz GFC 125MHz
Boot from SPI-NOR
Slimpro FW:
Ver: 2.4 (build 01.18.04.00 2015/08/13)
TPC: disabled
AVS: supported (margin: -0mV)
RST: supported
PWROFF: supported
PMD: 970 mV
SOC: 950 mV
Board: GIGABYTE MP30AR0 - AppliedMicro APM883408-xNA24SPT Customer Board
I2C: ready
DRAM: PHY calibrating ...PHY calibrating
...PHY calibrating ...PHY
calibrating ... ECC init
................****************................****************................****************................****************................****************................****************................****************................****************................****************................****************................****************................****************................****************................****************................****************................****************................****************................****************................****************................****************................****************................****************................****************................****************................****************................****************................****************................****************................****************................****************................****************................****************................
64 GiB @ 1333MHz
Non-contiguous multiple bank memory detected:
DDR region[0]: 0x0080000000 - 0x0fffffffff
DDR region[1]: 0x8000000000 - 0x807fffffff
SF: Detected MX25L25635F with page size 64 KiB, total 32 MiB
MMC: X-Gene SD/SDIO/eMMC: 0
PCIE0: (RC) link down
PCIE2: (RC) X1 GEN-1 link up
PCIE3: (RC) link down
00:00.0 - 10e8:e004 - Bridge device
01:00.0 - 1a03:1150 - Bridge device
02:00.0 - 1a03:2000 - Display controller
Video: ASPEED VGA Card (1a03, 2000) found @(2:0:0)
Mode: 1024x768x32 48kHz 60Hz
In: serial
Out: serial
Err: serial
CPUs: 00000001
Net: eth0
USB0: scanning bus 0 for devices... XHCI: WARN: Didn't find a matching TT
3 USB Device(s) found
USB1: scanning bus 1 for devices... 4 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
XHCI: ep 0x1 - rounding interval to 128 microframes
XHCI-ERR: xhci_submit_async_int !
Hit any key to stop autoboot: 5 4 3 2 1 0
reading mp30ar0_tianocore_ubt.fd
1835008 bytes read in 1165 ms (1.5 MiB/s)
reading mp30ar0_tianocore_sec_ubt.fd
262144 bytes read in 1011 ms (252.9 KiB/s)
## Starting application at 0x1D000000 ...
X-Gene Mp30ar0 Board
Boot firmware (version 1.20.03-uhp built at 11:18:31 on Feb 22 2016)
PROGRESS CODE: V3020003 I0
PROGRESS CODE: V3020002 I0
PROGRESS CODE: V3020003 I0
PROGRESS CODE: V3020002 I0
PROGRESS CODE: V3020003 I0
PROGRESS CODE: V3020002 I0
PROGRESS CODE: V3020003 I0
PROGRESS CODE: V3021001 I0
[2J[01;01H[=3h[2J[01;01H[2J[01;01H[=3h[2J[01;01H[2J[01;01H[=3h[2J[01;01H[2J[01;01H[=3h[2J[01;01HTianoCore
1.20.03-uhp UEFI 2.4.0 Feb 22 2016 11:17:26
CPU: APM ARM 64-bit Potenza Rev B0 2400MHz PCP 2400MHz
32 KB ICACHE, 32 KB DCACHE
SOC 2000MHz IOBAXI 400MHz AXI 250MHz AHB 200MHz GFC 125MHz
Board: X-Gene Mp30ar0 Board
Slimpro FW:
Ver: 2.4 (build 01.18.04.00 2015/08/13)
TPC: disable
AVS: support
PMD: 970 mV
SOC: 950 mV
The default boot selection will start in 5 seconds 4
seconds 3 seconds 2 seconds 1 second
#############
Mike.
--
Mike Howard
Reply to: