Re: 4.5.0-0.bpo.2-armmp does not boot on cubox-i
Hi,
I opened a bugreport against the kernel:
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=826518
Does anybody else see, that his cubox-i is not booting with newer kernels
anymore?
Thanks
Rainer
On Saturday 04 June 2016 14:35:29 Rainer Dorsch wrote:
> On Saturday 04 June 2016 13:27:04 Karsten Merker wrote:
> > On Sat, Jun 04, 2016 at 01:02:16PM +0200, Rainer Dorsch wrote:
> > > On Saturday 04 June 2016 12:43:00 Rainer Dorsch wrote:
> > > > On Saturday 04 June 2016 11:46:28 K. Merker wrote:
> > > > > On Thu, Jun 02, 2016 at 09:30:35PM +0200, Rainer Dorsch wrote:
> > > > > > after the upgrade to kernel 4.5.0-0.bpo.2-armmp, my cubox-i does
> > > > > > not
> > > > > > boot anymore. [...]
> >
> > [...]
> >
> > > Should I open a bug report against the kernel?
> >
> > Yes, that would be helpful. Could you perhaps give kernel 4.6
> > from experimental a try first? Kernel 4.6 has solved a number of
> > regressions that had shown up in 4.5, so it would be interesting
> > whether the problem still occurs with 4.6.
>
> 4.6.0 from experimental has the same issue:
>
> U-Boot 2014.10+dfsg1-2 (Nov 02 2014 - 00:31:26)
>
> CPU: Freescale i.MX6D rev1.2 at 792 MHz
> Reset cause: POR
> Board: MX6-CuBox-i
> DRAM: 1 GiB
> MMC: FSL_SDHC: 0
> In: serial
> Out: vga
> Err: vga
> Net: FEC [PRIME]
> (Re)start USB...
> USB0: Port not available.
> USB1: USB EHCI 1.00
> scanning bus 1 for devices... 1 USB Device(s) found
> scanning usb for storage devices... 0 Storage Device(s) found
> scanning usb for ethernet devices... 0 Ethernet Device(s) found
> Hit any key to stop autoboot: 0
> switch to partitions #0, OK
> mmc0 is current device
> ** File not found /boot.scr **
> ** File not found uEnv.txt **
> ** File not found /zImage **
> ** File not found /uImage **
> 938 bytes read in 89 ms (9.8 KiB/s)
> Running bootscript from mmc ...
> ## Executing script at 10800000
> 3620480 bytes read in 308 ms (11.2 MiB/s)
> 34350 bytes read in 231 ms (144.5 KiB/s)
> 15046745 bytes read in 13548 ms (1.1 MiB/s)
> Booting Debian 4.6.0-trunk-armmp from mmc 0:2...
> Kernel image @ 0x10800000 [ 0x000000 - 0x373e80 ]
> ## Flattened Device Tree blob at 18000000
> Booting using the fdt blob at 0x18000000
> EHCI failed to shut down host controller.
> Using Device Tree in place at 18000000, end 1800b62d
>
> Starting kernel ...
>
> [ 0.000000] Booting Linux on physical CPU 0x0
> [ 0.000000] Linux version 4.6.0-trunk-armmp (debian-
> kernel@lists.debian.org) (gcc version 5.3.1 20160509 (Debian 5.3.1-19) ) #1
> SMP Debian 4.6-1~exp1 (20)
> [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7),
> cr=10c5387d
> [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing
> instruction cache
> [ 0.000000] Machine model: SolidRun Cubox-i Dual/Quad
> [ 0.000000] efi: Getting EFI parameters from FDT:
> [ 0.000000] efi: UEFI not found.
> [ 0.000000] cma: Reserved 16 MiB at 0x4f000000
> [ 0.000000] Memory policy: Data cache writealloc
> [ 0.000000] percpu: Embedded 13 pages/cpu @ef6c0000 s20876 r8192 d24180
> u53248
> [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total
> pages: 260416
> [ 0.000000] Kernel command line: console=ttymxc0,115200
> root=/dev/mmcblk0p2 rootfstype=ext4 ro rootwait console=ttymxc0,115200
> console=tty1 elevator=noop [ 0.000000] PID hash table entries: 4096
> (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries:
> 131072 (order: 7, 524288 bytes)
> [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144
> bytes) [ 0.000000] Memory: 993568K/1048576K available (7773K kernel
> code, 932K rwdata, 2560K rodata, 1024K init, 390K bss, 38624K reserved,
> 16384K cma- reserved,)
> [ 0.000000] Virtual kernel memory layout:
> [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
> [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
> [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB)
> [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB)
> [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
> [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
> [ 0.000000] .text : 0xc0008000 - 0xc0b175d8 (11326 kB)
> [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB)
> [ 0.000000] .data : 0xc0d00000 - 0xc0de9274 ( 933 kB)
> [ 0.000000] .bss : 0xc0deb000 - 0xc0e4c9c4 ( 391 kB)
> [ 0.000000] Hierarchical RCU implementation.
> [ 0.000000] Build-time adjustment of leaf fanout to 32.
> [ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2.
> [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
> [ 0.000000] NR_IRQS:16 nr_irqs:16 16
> [ 0.000000] L2C-310 erratum 769419 enabled
> [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9
> [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9
> [ 0.000000] L2C-310 ID prefetch enabled, offset 1 lines
> [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
> [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB
> [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76070001
> [ 0.000000] Switching to timer-based delay loop, resolution 333ns
> [ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps
> every 715827882841ns
> [ 0.000027] clocksource: mxc_timer1: mask: 0xffffffff max_cycles:
> 0xffffffff, max_idle_ns: 637086815595 ns
> [ 0.002819] Console: colour dummy device 80x30
> [ 0.003690] console [tty1] enabled
> [ 0.003734] Calibrating delay loop (skipped), value calculated using
> timer frequency.. 6.00 BogoMIPS (lpj=12000)
> [ 0.003787] pid_max: default: 32768 minimum: 301
> [ 0.004004] Security Framework initialized
> [ 0.004034] Yama: disabled by default; enable with sysctl kernel.yama.*
> [ 0.004083] AppArmor: AppArmor disabled by boot time parameter
> [ 0.004168] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
> [ 0.004203] Mountpoint-cache hash table entries: 2048 (order: 1, 8192
> bytes)
> [ 0.005109] Disabling memory control group subsystem
> [ 0.005237] CPU: Testing write buffer coherency: ok
> [ 0.005292] ftrace: allocating 25599 entries in 76 pages
> [ 0.051928] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
> [ 0.052078] Setting up static identity map for 0x10100000 - 0x10100098
> [ 0.056882] EFI services will not be available.
> [ 0.058099] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
> [ 0.058208] Brought up 2 CPUs
> [ 0.058258] SMP: Total of 2 processors activated (12.00 BogoMIPS).
> [ 0.058281] CPU: All CPU(s) started in SVC mode.
> [ 0.059266] devtmpfs: initialized
> [ 0.069031] VFP support v0.3: implementor 41 architecture 3 part 30
> variant 9 rev 4
> [ 0.069775] clocksource: jiffies: mask: 0xffffffff max_cycles:
> 0xffffffff, max_idle_ns: 7645041785100000 ns
> [ 0.071056] pinctrl core: initialized pinctrl subsystem
> [ 0.072709] NET: Registered protocol family 16
> [ 0.075361] DMA: preallocated 256 KiB pool for atomic coherent
> allocations [ 0.077348] CPU identified as i.MX6Q, silicon rev 1.2
> [ 0.101546] No ATAGs?
> [ 0.101591] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1
> watchpoint registers.
> [ 0.101644] hw-breakpoint: maximum watchpoint size is 4 bytes.
> [ 0.103399] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
> [ 0.104043] Serial: AMBA PL011 UART driver
> [ 0.105005] imx-gpc 20dc000.gpc: failed to get pu regulator: -517
> [ 0.124092] mxs-dma 110000.dma-apbh: initialized
> [ 0.129451] vgaarb: loaded
> [ 0.130834] media: Linux media interface: v0.10
> [ 0.130925] Linux video capture interface: v2.00
> [ 0.131038] pps_core: LinuxPPS API ver. 1 registered
> [ 0.131062] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo
> Giometti <giometti@linux.it>
> [ 0.131120] PTP clock support registered
> [ 0.132999] clocksource: Switched to clocksource mxc_timer1
> [ 0.183201] VFS: Disk quotas dquot_6.6.0
> [ 0.183331] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096
> bytes) [ 0.198417] NET: Registered protocol family 2
> [ 0.199207] TCP established hash table entries: 8192 (order: 3, 32768
> bytes)
> [ 0.199322] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
> [ 0.199460] TCP: Hash tables configured (established 8192 bind 8192)
> [ 0.199577] UDP hash table entries: 512 (order: 2, 16384 bytes)
> [ 0.199649] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
> [ 0.199933] NET: Registered protocol family 1
> [ 0.200488] Unpacking initramfs...
> [ 1.298072] Freeing initrd memory: 14696K (c1800000 - c265a000)
> [ 1.305062] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7
> counters available
> [ 1.307390] futex hash table entries: 512 (order: 3, 32768 bytes)
> [ 1.307549] audit: initializing netlink subsys (disabled)
> [ 1.307637] audit: type=2000 audit(1.280:1): initialized
> [ 1.308448] Initialise system trusted keyring
> [ 1.308846] workingset: timestamp_bits=12 max_order=18 bucket_order=6
> [ 1.309054] zbud: loaded
> [ 1.787726] Key type asymmetric registered
> [ 1.787770] Asymmetric key parser 'x509' registered
> [ 1.787881] bounce: pool size: 64 pages
> [ 1.787977] Block layer SCSI generic (bsg) driver version 0.4 loaded
> (major 248)
> [ 1.788151] io scheduler noop registered (default)
> [ 1.788187] io scheduler deadline registered
> [ 1.788239] io scheduler cfq registered
> [ 1.795974] imx-sdma 20ec000.sdma: firmware: failed to load
> imx/sdma/sdma- imx6q.bin (-2)
> [ 1.796026] imx-sdma 20ec000.sdma: Direct firmware load for
> imx/sdma/sdma- imx6q.bin failed with error -2
> [ 1.802084] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
> [ 1.804393] Serial: AMBA driver
> [ 1.805321] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 25,
> base_baud = 5000000) is a IMX
> [ 2.463573] console [ttymxc0] enabled
> [ 2.468242] 21f0000.serial: ttymxc3 at MMIO 0x21f0000 (irq = 292,
> base_baud = 5000000) is a IMX
> [ 2.480979] 2188000.ethernet supply phy not found, using dummy regulator
> [ 2.493514] pps pps0: new PPS source ptp0
> [ 2.502940] at803x: module verification failed: signature and/or required
> key missing - tainting kernel
> [ 2.516949] libphy: fec_enet_mii_bus: probed
> [ 2.521951] fec 2188000.ethernet eth0: registered PHC device 0
> [ 2.528779] mousedev: PS/2 mouse device common for all mice
> [ 2.536861] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered
> 20cc000.snvs:snvs-r as rtc0
> [ 2.548557] ledtrig-cpu: registered to indicate activity on CPUs
> [ 2.557617] NET: Registered protocol family 10
> [ 2.563138] mip6: Mobile IPv6
> [ 2.566180] NET: Registered protocol family 17
> [ 2.570690] mpls_gso: MPLS GSO support
> [ 2.575533] ThumbEE CPU extension supported.
> [ 2.579913] Registering SWP/SWPB emulation handler
> [ 2.585746] registered taskstats version 1
> [ 2.589976] Loading compiled-in X.509 certificates
> [ 2.603616] alg: No test for pkcs1pad(rsa,sha256) (pkcs1pad(rsa-
> generic,sha256))
> [ 2.613851] Loaded X.509 cert 'Debian Project: Ben Hutchings:
> 008a018dca80932630'
> [ 2.621515] zswap: loaded using pool lzo/zbud
> [ 2.626529] imx-gpc 20dc000.gpc: failed to get pu regulator: -517
> [ 2.633914] input: gpio-keys as /devices/soc0/gpio-keys/input/input0
> [ 2.640442] snvs_rtc 20cc000.snvs:snvs-rtc-lp: setting system clock to
> 1970-01-01 00:00:00 UTC (0)
> [ 2.640505] imx-gpc 20dc000.gpc: failed to get pu regulator: -517
> [ 2.667981] brcm_reg: disabling
> [ 2.671191] usb_h1_vbus: disabling
> [ 2.674631] usb_otg_vbus: disabling
> [ 2.679771] Freeing unused kernel memory: 1024K (c0c00000 - c0d00000)
> [ 2.734205] systemd-udevd[77]: starting version 215
> [ 2.742207] random: systemd-udevd urandom read with 1 bits of entropy
> available
> [ 2.877463] imx-gpc 20dc000.gpc: failed to get pu regulator: -517
> [ 2.885185] imx-gpc 20dc000.gpc: failed to get pu regulator: -517
> [ 2.912790] sdhci: Secure Digital Host Controller Interface driver
> [ 2.919068] sdhci: Copyright(c) Pierre Ossman
> [ 2.930797] sdhci-pltfm: SDHCI platform and OF driver helper
> [ 2.940130] sdhci-esdhc-imx 2190000.usdhc: allocated mmc-pwrseq
> [ 2.971447] SCSI subsystem initialized
> [ 3.002582] ahci-imx 2200000.sata: fsl,transmit-level-mV value 1104,
> using 00000044
> [ 3.010353] ahci-imx 2200000.sata: fsl,transmit-boost-mdB value 0, using
> 00000000
> [ 3.017926] ahci-imx 2200000.sata: fsl,transmit-atten-16ths value 9,
> using 00002000
> [ 3.025662] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified,
> using 05000000
> [ 3.039927] ahci-imx 2200000.sata: SSS flag set, parallel bus scan
> disabled [ 3.046999] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1
> ports 3 Gbps 0x1 impl platform mode
> [ 3.055857] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only
> pmp pio slum part ccc apst
> [ 3.066715] scsi host0: ahci-imx
> [ 3.070417] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port
> 0x100 irq 295
> [ 3.213076] mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using
> ADMA
> [ 3.227066] sdhci-esdhc-imx 2194000.usdhc: could not get ultra high speed
> state, work on normal mode
> [ 3.239343] sdhci-esdhc-imx 2194000.usdhc: Got CD GPIO
> [ 3.257301] mmc0: queuing unknown CIS tuple 0x80 (2 bytes)
> [ 3.264558] mmc0: queuing unknown CIS tuple 0x80 (3 bytes)
> [ 3.273877] mmc0: queuing unknown CIS tuple 0x80 (3 bytes)
> [ 3.282498] mmc0: queuing unknown CIS tuple 0x80 (7 bytes)
> [ 3.288197] mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using
> ADMA
> [ 3.315837] mmc0: queuing unknown CIS tuple 0x80 (7 bytes)
> [ 3.348860] mmc1: host does not support reading read-only switch,
> assuming write-enable
> [ 3.363182] mmc1: new high speed SDHC card at address 59b4
> [ 3.370276] mmcblk1: mmc1:59b4 USDU1 29.5 GiB
> [ 3.376587] mmcblk1: p1 p2
> [ 3.388198] ata1: SATA link down (SStatus 0 SControl 300)
> [ 3.393710] ahci-imx 2200000.sata: no device found, disabling link.
> [ 3.400029] ahci-imx 2200000.sata: pass .hotplug=1 to enable hotplug
> [ 3.402833] mmc0: new high speed SDIO card at address 0001
> [ 33.683919] usbcore: registered new interface driver usbfs
> [ 33.689609] usbcore: registered new interface driver hub
> [ 33.695106] usbcore: registered new device driver usb
> [ 33.702900] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> [ 33.710293] ehci-pci: EHCI PCI platform driver
> [ 33.721816] ehci-orion: EHCI orion driver
> [ 33.744554] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
> [ 33.759893] hidraw: raw HID events driver (C) Jiri Kosina
> [ 33.767821] usbcore: registered new interface driver usbhid
> [ 33.773495] usbhid: USB HID core driver
>
>
> For reference I add the output with the old kernel:
>
> U-Boot 2014.10+dfsg1-2 (Nov 02 2014 - 00:31:26)
>
> CPU: Freescale i.MX6D rev1.2 at 792 MHz
> Reset cause: POR
> Board: MX6-CuBox-i
> DRAM: 1 GiB
> MMC: FSL_SDHC: 0
> In: serial
> Out: vga
> Err: vga
> Net: FEC [PRIME]
> (Re)start USB...
> USB0: Port not available.
> USB1: USB EHCI 1.00
> scanning bus 1 for devices... 1 USB Device(s) found
> scanning usb for storage devices... 0 Storage Device(s) found
> scanning usb for ethernet devices... 0 Ethernet Device(s) found
> Hit any key to stop autoboot: 0
> CuBox-i U-Boot > setenv kvers 4.5.0-0.bpo.1-armmp
> CuBox-i U-Boot > run bootcmd
> switch to partitions #0, OK
> mmc0 is current device
> ** File not found /boot.scr **
> ** File not found uEnv.txt **
> ** File not found /zImage **
> ** File not found /uImage **
> 938 bytes read in 89 ms (9.8 KiB/s)
> Running bootscript from mmc ...
> ## Executing script at 10800000
> 3571344 bytes read in 300 ms (11.4 MiB/s)
> 34233 bytes read in 133 ms (251 KiB/s)
> 15010048 bytes read in 882 ms (16.2 MiB/s)
> Booting Debian 4.5.0-0.bpo.1-armmp from mmc 0:2...
> Kernel image @ 0x10800000 [ 0x000000 - 0x367e90 ]
> ## Flattened Device Tree blob at 18000000
> Booting using the fdt blob at 0x18000000
> EHCI failed to shut down host controller.
> Using Device Tree in place at 18000000, end 1800b5b8
>
> Starting kernel ...
>
> [ 0.000000] Booting Linux on physical CPU 0x0
> [ 0.000000] Linux version 4.5.0-0.bpo.1-armmp (debian-
> kernel@lists.debian.org) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 SMP
> Debian 4.5.1-1~bpo8+1 (2016-)
> [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7),
> cr=10c5387d
> [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing
> instruction cache
> [ 0.000000] Machine model: SolidRun Cubox-i Dual/Quad
> [ 0.000000] Memory policy: Data cache writealloc
> [ 0.000000] PERCPU: Embedded 12 pages/cpu @ef6c2000 s20032 r8192 d20928
> u49152
> [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total
> pages: 260416
> [ 0.000000] Kernel command line: console=ttymxc0,115200
> root=/dev/mmcblk0p2 rootfstype=ext4 ro rootwait console=ttymxc0,115200
> console=tty1 elevator=noop [ 0.000000] PID hash table entries: 4096
> (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries:
> 131072 (order: 7, 524288 bytes)
> [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144
> bytes) [ 0.000000] Memory: 1011524K/1048576K available (7288K kernel
> code, 921K rwdata, 2528K rodata, 940K init, 394K bss, 37052K reserved, 0K
> cma-reserved, 262)
> [ 0.000000] Virtual kernel memory layout:
> [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
> [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
> [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB)
> [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB)
> [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
> [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
> [ 0.000000] .text : 0xc0008000 - 0xc099e3bc (9817 kB)
> [ 0.000000] .init : 0xc099f000 - 0xc0a8a000 ( 940 kB)
> [ 0.000000] .data : 0xc0a8a000 - 0xc0b706fc ( 922 kB)
> [ 0.000000] .bss : 0xc0b73000 - 0xc0bd5984 ( 395 kB)
> [ 0.000000] Hierarchical RCU implementation.
> [ 0.000000] Build-time adjustment of leaf fanout to 32.
> [ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2.
> [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
> [ 0.000000] NR_IRQS:16 nr_irqs:16 16
> [ 0.000000] L2C-310 erratum 769419 enabled
> [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9
> [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9
> [ 0.000000] L2C-310 ID prefetch enabled, offset 1 lines
> [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
> [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB
> [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76070001
> [ 0.000000] Switching to timer-based delay loop, resolution 333ns
> [ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps
> every 715827882841ns
> [ 0.000026] clocksource: mxc_timer1: mask: 0xffffffff max_cycles:
> 0xffffffff, max_idle_ns: 637086815595 ns
> [ 0.002806] Console: colour dummy device 80x30
> [ 0.003599] console [tty1] enabled
> [ 0.003641] Calibrating delay loop (skipped), value calculated using
> timer frequency.. 6.00 BogoMIPS (lpj=12000)
> [ 0.003692] pid_max: default: 32768 minimum: 301
> [ 0.003904] Security Framework initialized
> [ 0.003936] Yama: disabled by default; enable with sysctl kernel.yama.*
> [ 0.003983] AppArmor: AppArmor disabled by boot time parameter
> [ 0.004067] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
> [ 0.004102] Mountpoint-cache hash table entries: 2048 (order: 1, 8192
> bytes)
> [ 0.004934] Disabling memory control group subsystem
> [ 0.005064] CPU: Testing write buffer coherency: ok
> [ 0.005118] ftrace: allocating 25233 entries in 74 pages
> [ 0.050727] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
> [ 0.050891] Setting up static identity map for 0x10008280 - 0x10008318
> [ 0.056614] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
> [ 0.056712] Brought up 2 CPUs
> [ 0.056765] SMP: Total of 2 processors activated (12.00 BogoMIPS).
> [ 0.056788] CPU: All CPU(s) started in SVC mode.
> [ 0.057669] devtmpfs: initialized
> [ 0.067281] VFP support v0.3: implementor 41 architecture 3 part 30
> variant 9 rev 4
> [ 0.068029] clocksource: jiffies: mask: 0xffffffff max_cycles:
> 0xffffffff, max_idle_ns: 7645041785100000 ns
> [ 0.068313] pinctrl core: initialized pinctrl subsystem
> [ 0.069755] NET: Registered protocol family 16
> [ 0.070687] DMA: preallocated 256 KiB pool for atomic coherent
> allocations [ 0.072639] CPU identified as i.MX6Q, silicon rev 1.2
> [ 0.094673] No ATAGs?
> [ 0.094715] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1
> watchpoint registers.
> [ 0.094767] hw-breakpoint: maximum watchpoint size is 4 bytes.
> [ 0.096379] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
> [ 0.096996] Serial: AMBA PL011 UART driver
> [ 0.097942] imx-gpc 20dc000.gpc: failed to get pu regulator: -517
> [ 0.115893] mxs-dma 110000.dma-apbh: initialized
> [ 0.121085] vgaarb: loaded
> [ 0.122451] media: Linux media interface: v0.10
> [ 0.122531] Linux video capture interface: v2.00
> [ 0.122636] pps_core: LinuxPPS API ver. 1 registered
> [ 0.122658] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo
> Giometti <giometti@linux.it>
> [ 0.122710] PTP clock support registered
> [ 0.124461] clocksource: Switched to clocksource mxc_timer1
> [ 0.172052] VFS: Disk quotas dquot_6.6.0
> [ 0.172176] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096
> bytes) [ 0.186867] NET: Registered protocol family 2
> [ 0.187647] TCP established hash table entries: 8192 (order: 3, 32768
> bytes)
> [ 0.187760] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
> [ 0.187898] TCP: Hash tables configured (established 8192 bind 8192)
> [ 0.188014] UDP hash table entries: 512 (order: 2, 16384 bytes)
> [ 0.188082] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
> [ 0.188365] NET: Registered protocol family 1
> [ 0.188994] Unpacking initramfs...
> [ 1.271906] Freeing initrd memory: 14660K (c1800000 - c2651000)
> [ 1.279187] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7
> counters available
> [ 1.281493] futex hash table entries: 512 (order: 3, 32768 bytes)
> [ 1.281646] audit: initializing netlink subsys (disabled)
> [ 1.281730] audit: type=2000 audit(1.260:1): initialized
> [ 1.282567] Initialise system trusted keyring
> [ 1.283117] zbud: loaded
> [ 1.285970] Key type asymmetric registered
> [ 1.286011] Asymmetric key parser 'x509' registered
> [ 1.286117] bounce: pool size: 64 pages
> [ 1.286214] Block layer SCSI generic (bsg) driver version 0.4 loaded
> (major 249)
> [ 1.286389] io scheduler noop registered (default)
> [ 1.286428] io scheduler deadline registered
> [ 1.286481] io scheduler cfq registered
> [ 1.293925] imx-sdma 20ec000.sdma: firmware: failed to load
> imx/sdma/sdma- imx6q.bin (-2)
> [ 1.293975] imx-sdma 20ec000.sdma: Direct firmware load for
> imx/sdma/sdma- imx6q.bin failed with error -2
> [ 1.299578] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
> [ 1.301901] Serial: AMBA driver
> [ 1.302747] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 25,
> base_baud = 5000000) is a IMX
> [ 1.936888] console [ttymxc0] enabled
> [ 1.941571] 21f0000.serial: ttymxc3 at MMIO 0x21f0000 (irq = 292,
> base_baud = 5000000) is a IMX
> [ 1.954293] 2188000.ethernet supply phy not found, using dummy regulator
> [ 1.968973] pps pps0: new PPS source ptp0
> [ 1.978415] at803x: module verification failed: signature and/or required
> key missing - tainting kernel
> [ 1.992490] libphy: fec_enet_mii_bus: probed
> [ 1.997424] fec 2188000.ethernet eth0: registered PHC device 0
> [ 2.004239] mousedev: PS/2 mouse device common for all mice
> [ 2.012214] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered
> 20cc000.snvs:snvs-r as rtc0
> [ 2.023905] ledtrig-cpu: registered to indicate activity on CPUs
> [ 2.032415] NET: Registered protocol family 10
> [ 2.037913] mip6: Mobile IPv6
> [ 2.040983] NET: Registered protocol family 17
> [ 2.045492] mpls_gso: MPLS GSO support
> [ 2.050312] ThumbEE CPU extension supported.
> [ 2.054689] Registering SWP/SWPB emulation handler
> [ 2.060530] registered taskstats version 1
> [ 2.064722] Loading compiled-in X.509 certificates
> [ 2.072275] Loaded X.509 cert 'Debian Project: Ben Hutchings:
> 008a018dca80932630'
> [ 2.079931] zswap: loaded using pool lzo/zbud
> [ 2.085005] imx-gpc 20dc000.gpc: failed to get pu regulator: -517
> [ 2.092225] input: gpio-keys as /devices/soc0/gpio-keys/input/input0
> [ 2.098748] snvs_rtc 20cc000.snvs:snvs-rtc-lp: setting system clock to
> 1970-01-01 00:00:00 UTC (0)
> [ 2.098800] imx-gpc 20dc000.gpc: failed to get pu regulator: -517
> [ 2.126638] brcm_reg: disabling
> [ 2.129841] usb_h1_vbus: disabling
> [ 2.133275] usb_otg_vbus: disabling
> [ 2.138145] Freeing unused kernel memory: 940K (c099f000 - c0a8a000)
> [ 2.192000] systemd-udevd[67]: starting version 215
> [ 2.200012] random: systemd-udevd urandom read with 1 bits of entropy
> available
> [ 2.305373] SCSI subsystem initialized
> [ 2.345986] imx-gpc 20dc000.gpc: failed to get pu regulator: -517
> [ 2.363482] ahci-imx 2200000.sata: fsl,transmit-level-mV value 1104,
> using 00000044
> [ 2.371275] ahci-imx 2200000.sata: fsl,transmit-boost-mdB value 0, using
> 00000000
> [ 2.374346] sdhci: Secure Digital Host Controller Interface driver
> [ 2.374348] sdhci: Copyright(c) Pierre Ossman
> [ 2.375232] sdhci-pltfm: SDHCI platform and OF driver helper
> [ 2.377344] /soc/aips-bus@02100000/usdhc@02190000: voltage-ranges
> unspecified
> [ 2.377353] sdhci-esdhc-imx 2190000.usdhc: could not get ultra high speed
> state, work on normal mode
> [ 2.377673] sdhci-esdhc-imx 2190000.usdhc: allocated mmc-pwrseq
> [ 2.417576] ahci-imx 2200000.sata: fsl,transmit-atten-16ths value 9,
> using 00002000
> [ 2.425304] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified,
> using 05000000
> [ 2.440142] ahci-imx 2200000.sata: SSS flag set, parallel bus scan
> disabled [ 2.447226] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1
> ports 3 Gbps 0x1 impl platform mode
> [ 2.456097] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only
> pmp pio slum part ccc apst
> [ 2.467300] scsi host0: ahci-imx
> [ 2.471017] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port
> 0x100 irq 295
> [ 2.632549] mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using
> ADMA
> [ 2.640433] /soc/aips-bus@02100000/usdhc@02194000: voltage-ranges
> unspecified
> [ 2.647653] sdhci-esdhc-imx 2194000.usdhc: could not get ultra high speed
> state, work on normal mode
> [ 2.658918] sdhci-esdhc-imx 2194000.usdhc: Got CD GPIO
> [ 2.680193] mmc0: queuing unknown CIS tuple 0x80 (2 bytes)
> [ 2.687447] mmc0: queuing unknown CIS tuple 0x80 (3 bytes)
> [ 2.696771] mmc0: queuing unknown CIS tuple 0x80 (3 bytes)
> [ 2.705404] mmc0: queuing unknown CIS tuple 0x80 (7 bytes)
> [ 2.711126] mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using
> ADMA
> [ 2.734972] mmc0: queuing unknown CIS tuple 0x80 (7 bytes)
> [ 2.772217] mmc1: host does not support reading read-only switch,
> assuming write-enable
> [ 2.786480] mmc1: new high speed SDHC card at address 59b4
> [ 2.788623] ata1: SATA link down (SStatus 0 SControl 300)
> [ 2.788668] ahci-imx 2200000.sata: no device found, disabling link.
> [ 2.788674] ahci-imx 2200000.sata: pass .hotplug=1 to enable hotplug
> [ 2.813851] mmcblk0: mmc1:59b4 USDU1 29.5 GiB
> [ 2.819802] mmcblk0: p1 p2
> [ 2.843994] mmc0: new high speed SDIO card at address 0001
> [ 3.295906] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data
> mode. Opts: (null)
> [ 3.739803] systemd[1]: systemd 215 running in system mode. (+PAM +AUDIT
> +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ -SECCOMP -APPARMOR)
> [ 3.753463] systemd[1]: Detected architecture 'arm'.
> [ 3.849841] systemd[1]: Inserted module 'autofs4'
> [ 3.855935] systemd[1]: Set hostname to <home>.
> [ 4.312773] systemd[1]: Cannot add dependency job for unit display-
> manager.service, ignoring: Unit display-manager.service failed to load: No
> such file o.
> [ 4.327927] systemd[1]: Found ordering cycle on basic.target/start
> [ 4.334183] systemd[1]: Found dependency on sysinit.target/start
> [ 4.340252] systemd[1]: Found dependency on
> systemd-journald.service/start [ 4.347187] systemd[1]: Found dependency
> on systemd-journald-dev- log.socket/start
> [ 4.354725] systemd[1]: Found dependency on rtcemu.service/start
> [ 4.360833] systemd[1]: Found dependency on basic.target/start
> [ 4.366745] systemd[1]: Breaking ordering cycle by deleting job systemd-
> journald.service/start
> [ 4.375432] systemd[1]: Job systemd-journald.service/start deleted to
> break ordering cycle starting with basic.target/start
> [ 4.387106] systemd[1]: Found ordering cycle on basic.target/start
> [ 4.393367] systemd[1]: Found dependency on sockets.target/start
> [ 4.399447] systemd[1]: Found dependency on systemd-journald-dev-
> log.socket/start
> [ 4.406994] systemd[1]: Found dependency on rtcemu.service/start
> [ 4.413054] systemd[1]: Found dependency on basic.target/start
> [ 4.418942] systemd[1]: Breaking ordering cycle by deleting job
> sockets.target/start
> [ 4.426748] systemd[1]: Job sockets.target/start deleted to break
> ordering cycle starting with basic.target/start
> [ 4.439930] systemd[1]: Starting Forward Password Requests to Wall
> Directory Watch.
> [ 4.448001] systemd[1]: Started Forward Password Requests to Wall
> Directory Watch.
> [ 4.455711] systemd[1]: Expecting device dev-ttymxc0.device...
> [ 4.461828] systemd[1]: Starting Remote File Systems (Pre).
> [ 4.467696] systemd[1]: Reached target Remote File Systems (Pre).
> [ 4.473931] systemd[1]: Starting Encrypted Volumes.
> [ 4.479094] systemd[1]: Reached target Encrypted Volumes.
> [ 4.484684] systemd[1]: Starting Arbitrary Executable File Formats File
> System Automount Point.
> [ 4.494301] systemd[1]: Set up automount Arbitrary Executable File
> Formats File System Automount Point.
> [ 4.503867] systemd[1]: Starting Dispatch Password Requests to Console
> Directory Watch.
> [ 4.512159] systemd[1]: Started Dispatch Password Requests to Console
> Directory Watch.
> [ 4.520201] systemd[1]: Starting Paths.
> [ 4.524302] systemd[1]: Reached target Paths.
> [ 4.528780] systemd[1]: Expecting device dev-disk-
> by\x2duuid-07b3f3c9\x2ddeef\x2d4b5c\x2d8dc8\x2d7ffcb7b81a11.device...
> [ 4.539846] systemd[1]: Starting Root Slice.
> [ 4.544488] systemd[1]: Created slice Root Slice.
> [ 4.549306] systemd[1]: Starting User and Session Slice.
> [ 4.555055] systemd[1]: Created slice User and Session Slice.
> [ 4.560926] systemd[1]: Starting Delayed Shutdown Socket.
> [ 4.566699] systemd[1]: Listening on Delayed Shutdown Socket.
> [ 4.572569] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
> [ 4.579600] systemd[1]: Listening on /dev/initctl Compatibility Named
> Pipe. [ 4.586706] systemd[1]: Starting udev Control Socket.
> [ 4.592118] systemd[1]: Listening on udev Control Socket.
> [ 4.597657] systemd[1]: Starting udev Kernel Socket.
> [ 4.602953] systemd[1]: Listening on udev Kernel Socket.
> [ 4.608405] systemd[1]: Starting Journal Socket.
> [ 4.613493] systemd[1]: Listening on Journal Socket.
> [ 4.618628] systemd[1]: Starting System Slice.
> [ 4.623513] systemd[1]: Created slice System Slice.
> [ 4.628592] systemd[1]: Started File System Check on Root Device.
> [ 4.634798] systemd[1]: Starting system-getty.slice.
> [ 4.640261] systemd[1]: Created slice system-getty.slice.
> [ 4.645784] systemd[1]: Starting system-serial\x2dgetty.slice.
> [ 4.652098] systemd[1]: Created slice system-serial\x2dgetty.slice.
> [ 4.658557] systemd[1]: Starting Increase datagram queue length...
> [ 4.677267] systemd[1]: Mounted Huge Pages File System.
> [ 4.704076] systemd[1]: Started Set Up Additional Binary Formats.
> [ 4.714341] systemd[1]: Starting Load Kernel Modules...
> [ 4.733297] systemd[1]: Starting udev Coldplug all Devices...
> [ 4.750503] systemd[1]: Starting Create list of required static device
> nodes for the current kernel...
> [ 4.765346] systemd[1]: Mounting POSIX Message Queue File System...
> [ 4.777646] systemd[1]: Mounting Debug File System...
> [ 4.781081] fuse init (API version 7.24)
> [ 4.791114] systemd[1]: Starting Slices.
> [ 4.796095] systemd[1]: Reached target Slices.
> [ 4.804353] systemd[1]: Started Increase datagram queue length.
> [ 4.813002] systemd[1]: Found ordering cycle on systemd-
> journald.service/start
> [ 4.822336] systemd[1]: Found dependency on systemd-journald-dev-
> log.socket/start
> [ 4.830583] systemd[1]: Found dependency on rtcemu.service/start
> [ 4.840550] systemd[1]: Found dependency on basic.target/start
> [ 4.851822] systemd[1]: Found dependency on sysinit.target/start
> [ 4.861203] systemd[1]: Found dependency on
> systemd-journald.service/start [ 4.868351] systemd[1]: Breaking ordering
> cycle by deleting job systemd- journald-dev-log.socket/start
> [ 4.877718] systemd[1]: Job systemd-journald-dev-log.socket/start deleted
> to break ordering cycle starting with systemd-journald.service/start [
> 4.891092] systemd[1]: Found ordering cycle on systemd-
> journald.service/start
> [ 4.898445] systemd[1]: Found dependency on systemd-journald-dev-
> log.socket/start
> [ 4.906035] systemd[1]: Found dependency on rtcemu.service/start
> [ 4.912134] systemd[1]: Found dependency on basic.target/start
> [ 4.918058] systemd[1]: Found dependency on sysinit.target/start
> [ 4.924130] systemd[1]: Found dependency on
> systemd-journald.service/start [ 4.931063] systemd[1]: Unable to break
> cycle
> [ 4.935491] systemd[1]: Requested transaction contains an unfixable
> cyclic ordering dependency: Transaction order is cyclic. See system logs
> for details. [ 4.949309] systemd[1]: systemd-journald.socket failed to
> queue service startup job (Maybe the service file is missing or not a
> non-template unit?): Tran.
> [ 4.967892] systemd[1]: Unit systemd-journald.socket entered failed
> state. [ 4.975984] systemd[1]: Mounted Debug File System.
> [ 4.981197] systemd[1]: Mounted POSIX Message Queue File System.
> [ 4.988631] systemd[1]: Started Load Kernel Modules.
> [ 5.010875] systemd[1]: Started Create list of required static device
> nodes for the current kernel.
> [ 5.061136] systemd[1]: Started udev Coldplug all Devices.
> [ 5.128324] systemd[1]: Starting Create Static Device Nodes in /dev...
> [ 5.149584] systemd[1]: Mounted Configuration File System.
> [ 5.155371] systemd[1]: Starting Apply Kernel Variables...
> [ 5.164636] systemd[1]: Mounting FUSE Control File System...
> [ 5.174431] systemd[1]: Starting Syslog Socket.
> [ 5.179691] systemd[1]: Listening on Syslog Socket.
> [ 5.197817] systemd[1]: Mounted FUSE Control File System.
> [ 5.205097] systemd[1]: Started Apply Kernel Variables.
> [ 5.278240] systemd[1]: Started Create Static Device Nodes in /dev.
> [ 5.291699] systemd[1]: Starting udev Kernel Device Manager...
> [ 5.324905] systemd-udevd[156]: starting version 215
> [ 5.330269] systemd[1]: Started udev Kernel Device Manager.
> [ 5.336294] systemd[1]: Starting Copy rules generated while the root was
> ro...
> [ 5.357328] systemd[1]: Starting LSB: Set preliminary keymap...
> [ 5.375775] systemd[1]: Started Copy rules generated while the root was
> ro. [ 5.387172] systemd[1]: Started LSB: Set preliminary keymap.
> [ 5.400993] systemd[1]: Starting Remount Root and Kernel File Systems...
> [ 5.603164] EXT4-fs (mmcblk0p2): re-mounted. Opts:
> discard,data=ordered,errors=remount-ro
> [ 5.614370] systemd[1]: Started Remount Root and Kernel File Systems.
> [ 5.629386] systemd[1]: Started Various fixups to make systemd work
> better on Debian.
> [ 5.637681] systemd[1]: Starting Load/Save Random Seed...
> [ 5.661386] systemd[1]: Starting Local File Systems (Pre).
> [ 5.667304] systemd[1]: Reached target Local File Systems (Pre).
> [ 5.673554] systemd[1]: Mounting /tmp...
> [ 5.716974] systemd[1]: Started Load/Save Random Seed.
> [ 5.734394] systemd[1]: Mounted /tmp.
> [ 5.835999] systemd[1]: Starting Local File Systems.
> [ 5.842767] systemd[1]: Reached target Local File Systems.
> [ 5.849879] systemd[1]: Starting Create Volatile Files and Directories...
> [ 5.885415] systemd[1]: Starting Remote File Systems.
> [ 5.893126] systemd[1]: Reached target Remote File Systems.
> [ 5.898985] systemd[1]: Starting LSB: Set console font and keymap...
> [ 5.934816] systemd[1]: Starting LSB: Raise network interfaces....
> [ 5.997960] Registered IR keymap rc-empty
> [ 6.004722] input: gpio_ir_recv as
> /devices/soc0/ir-receiver/rc/rc0/input1 [ 6.018326] systemd[1]: Started
> Create Volatile Files and Directories. [ 6.035455] rc rc0: gpio_ir_recv
> as /devices/soc0/ir-receiver/rc/rc0 [ 6.054005] systemd[1]: Started LSB:
> Set console font and keymap. [ 6.103240] imx2-wdt 20bc000.wdog: timeout
> 60 sec (nowayout=0)
> [ 6.103447] [drm] Initialized drm 1.1.0 20060810
> [ 6.135012] etnaviv gpu-subsystem: bound 134000.gpu (ops gpu_ops
> [etnaviv]) [ 6.139290] lirc_dev: IR Remote Control driver registered,
> major 244 [ 6.151225] rc rc0: lirc_dev: driver ir-lirc-codec
> (gpio-rc-recv) registered at minor = 0
> [ 6.159554] IR LIRC bridge handler initialized
> [ 6.225980] etnaviv gpu-subsystem: bound 130000.gpu (ops gpu_ops
> [etnaviv]) [ 6.233422] systemd[1]: Found device /dev/ttymxc0.
> [ 6.273175] etnaviv gpu-subsystem: bound 2204000.gpu (ops gpu_ops
> [etnaviv])
> [ 6.300511] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007
> [ 6.313150] i2c i2c-1: IMX I2C adapter registered
> [ 6.324883] i2c i2c-1: can't use DMA, using PIO instead.
> [ 6.329618] usbcore: registered new interface driver usbfs
> [ 6.329688] usbcore: registered new interface driver hub
> [ 6.334666] systemd[1]: Starting Update UTMP about System
> Boot/Shutdown... [ 6.334822] usbcore: registered new device driver usb
> [ 6.377232] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108
> [ 6.390688] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> [ 6.416070] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215
> [ 6.422242] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0
> [ 6.428557] etnaviv-gpu 2204000.gpu: hw init failed: -6
> [ 6.474874] rtc-pcf8523 2-0068: rtc core: registered rtc-pcf8523 as rtc1
> [ 6.497711] i2c i2c-2: IMX I2C adapter registered
> [ 6.514315] i2c i2c-2: can't use DMA, using PIO instead.
> [ 6.522770] systemd[1]: Started Update UTMP about System Boot/Shutdown.
> [ 6.569734] ci_hdrc ci_hdrc.0: EHCI Host Controller
> [ 6.581655] imx-ipuv3 2400000.ipu: IPUv3H probed
> [ 6.583826] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus
> number 1
> [ 6.593412] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
> [ 6.593719] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
> [ 6.593727] usb usb1: New USB device strings: Mfr=3, Product=2,
> SerialNumber=1
> [ 6.593733] usb usb1: Product: EHCI Host Controller
> [ 6.593738] usb usb1: Manufacturer: Linux 4.5.0-0.bpo.1-armmp ehci_hcd
> [ 6.593743] usb usb1: SerialNumber: ci_hdrc.0
> [ 6.594520] hub 1-0:1.0: USB hub found
> [ 6.594561] hub 1-0:1.0: 1 port detected
> [ 6.610929] ci_hdrc ci_hdrc.1: EHCI Host Controller
> [ 6.610965] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus
> number 2
> [ 6.620532] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
> [ 6.620832] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
> [ 6.620840] usb usb2: New USB device strings: Mfr=3, Product=2,
> SerialNumber=1
> [ 6.620846] usb usb2: Product: EHCI Host Controller
> [ 6.620851] usb usb2: Manufacturer: Linux 4.5.0-0.bpo.1-armmp ehci_hcd
> [ 6.620856] usb usb2: SerialNumber: ci_hdrc.1
> [ 6.621632] hub 2-0:1.0: USB hub found
> [ 6.621681] hub 2-0:1.0: 1 port detected
> [ 6.678802] imx-spdif sound-spdif: snd-soc-dummy-dai <-> 2004000.spdif
> mapping ok
> [ 6.706152] imx-ipuv3 2800000.ipu: IPUv3H probed
> [ 6.715981] systemd[1]: Found device /dev/disk/by-uuid/07b3f3c9-
> deef-4b5c-8dc8-7ffcb7b81a11.
> [ 6.780926] usbcore: registered new interface driver brcmfmac
> [ 6.794436] systemd[1]: Activating swap /dev/disk/by-uuid/07b3f3c9-
> deef-4b5c-8dc8-7ffcb7b81a11...
> [ 6.847179] brcmfmac_sdio mmc0:0001:1: firmware: direct-loading firmware
> brcm/brcmfmac4330-sdio.bin
> [ 6.876525] brcmfmac_sdio mmc0:0001:1: firmware: failed to load
> brcm/brcmfmac4330-sdio.txt (-2)
> [ 6.885371] brcmfmac_sdio mmc0:0001:1: Direct firmware load for
> brcm/brcmfmac4330-sdio.txt failed with error -2
> [ 6.911276] systemd[1]: Starting Sound Card.
> [ 6.916876] systemd[1]: Reached target Sound Card.
> [ 6.920538] usb 1-1: new full-speed USB device number 2 using ci_hdrc
> [ 6.929236] systemd[1]: Starting system-ifup.slice.
> [ 6.935161] Adding 4194300k swap on /dev/mmcblk0p1. Priority:-1
> extents:1 across:4194300k SSFS
> [ 6.944342] systemd[1]: Created slice system-ifup.slice.
> [ 6.956622] systemd[1]: Activated swap /dev/disk/by-uuid/07b3f3c9-
> deef-4b5c-8dc8-7ffcb7b81a11.
> [ 6.979633] systemd[1]: Starting Swap.
> [ 6.983851] systemd[1]: Reached target Swap.
> [ 7.056093] usb 1-1: New USB device found, idVendor=04fa, idProduct=2490
> [ 7.062873] usb 1-1: New USB device strings: Mfr=0, Product=0,
> SerialNumber=0
> [ 7.477478] Atheros 8035 ethernet 2188000.ethernet:00: attached PHY
> driver [Atheros 8035 ethernet] (mii_bus:phy_addr=2188000.ethernet:00,
> irq=-1) [ 7.490823] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
> [ 7.511530] systemd[1]: Started LSB: Raise network interfaces..
> [ 7.518570] systemd[1]: Starting ifup for eth0...
> [ 7.537642] systemd[1]: Started ifup for eth0.
> [ 7.543951] systemd[1]: Starting Network.
> [ 7.548528] systemd[1]: Reached target Network.
> [ 7.553411] systemd[1]: Starting Network is Online.
> [ 7.558770] systemd[1]: Reached target Network is Online.
> [ 7.564377] systemd[1]: Starting LSB: RPC portmapper replacement...
> [ 7.825287] systemd[1]: Started LSB: RPC portmapper replacement.
> [ 7.832370] systemd[1]: Starting RPC Port Mapper.
> [ 7.837437] systemd[1]: Reached target RPC Port Mapper.
> [ 7.842782] systemd[1]: Starting LSB: NFS support files common to client
> and server...
> [ 7.928592] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000):
> clkctl 0x50
> [ 8.140870] RPC: Registered named UNIX socket transport module.
> [ 8.146870] RPC: Registered udp transport module.
> [ 8.151628] RPC: Registered tcp transport module.
> [ 8.156364] RPC: Registered tcp NFSv4.1 backchannel transport module.
> [ 8.192869] FS-Cache: Loaded
> [ 8.243229] FS-Cache: Netfs 'nfs' registered for caching
> [ 8.308238] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
> [ 8.401693] systemd[1]: Started LSB: NFS support files common to client
> and server.
> [ 8.410250] systemd[1]: Starting System Initialization.
> [ 8.415793] systemd[1]: Reached target System Initialization.
> [ 8.421676] systemd[1]: Starting D-Bus System Message Bus Socket.
> [ 8.428202] systemd[1]: Listening on D-Bus System Message Bus Socket.
> [ 8.434783] systemd[1]: Starting Daily Cleanup of Temporary Directories.
> [ 8.441658] systemd[1]: Started Daily Cleanup of Temporary Directories.
> [ 8.448425] systemd[1]: Starting Timers.
> [ 8.452650] systemd[1]: Reached target Timers.
> [ 8.457230] systemd[1]: Starting Basic System.
> [ 8.461954] systemd[1]: Reached target Basic System.
> [ 8.475609] systemd[1]: Starting OpenBSD Secure Shell server...
> [ 8.497672] systemd[1]: Started OpenBSD Secure Shell server.
> [ 8.504095] systemd[1]: Starting Regular background program processing
> daemon...
> [ 8.517751] systemd[1]: Started Regular background program processing
> daemon.
> [ 8.525805] systemd[1]: Starting Initialize hardware monitoring
> sensors... [ 8.537287] systemd[1]: Starting Deferred execution
> scheduler... [ 8.548834] systemd[1]: Started Deferred execution
> scheduler.
> [ 8.555486] systemd[1]: Starting Restore /etc/resolv.conf if the system
> crashed before the ppp link was shut down....
> [ 8.570847] systemd[1]: Starting Run anacron jobs...
> [ 8.581435] systemd[1]: Started Run anacron jobs.
> [ 8.586951] systemd[1]: Starting /etc/rc.local Compatibility...
> [ 8.597017] systemd[1]: Starting Login Service...
> [ 8.606655] systemd[1]: Started getty on tty2-tty6 if dbus and logind are
> not available.
> [ 8.615289] systemd[1]: Starting LSB: start Samba daemons for the AD
> DC... [ 8.635518] systemd[1]: Starting LSB: X display manager for KDE...
> [ 8.646505] systemd[1]: Starting LSB: apt-cacher package caching proxy
> daemon...
> [ 8.667786] systemd[1]: Starting LSB: start Samba NetBIOS nameserver
> (nmbd)...
> [ 8.685413] systemd[1]: Starting LSB: keep memory of all UPnP devices
> that announced themselves...
> [ 8.710832] systemd[1]: Starting LSB: Increased Performance In Linux With
> zRam (Virtual Swap Compressed in RAM)...
> [ 8.725724] systemd[1]: Starting LSB: emulates the RTC by setting the
> clock to the /var/log/syslog write time as early as possible...
> [ 8.746931] systemd[1]: Starting D-Bus System Message Bus...
> [ 8.778534] systemd[1]: Started D-Bus System Message Bus.
> [ 8.936675] zram: Added device: zram0
> [ 8.942715] zram: Added device: zram1
> [ 8.956573] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000):
> clkctl 0x50
> [ 8.987975] zram0: detected capacity change from 0 to 525889536
> [ 8.995671] zram1: detected capacity change from 0 to 525889536
> [ 9.080556] Adding 513560k swap on /dev/zram0. Priority:100 extents:1
> across:513560k SSFS
> [ 9.102474] Adding 513560k swap on /dev/zram1. Priority:100 extents:1
> across:513560k SSFS
> [ 9.194254] systemd[1]: Starting System Logging Service...
> [ 9.221463] systemd[1]: Starting Permit User Sessions...
> [ 9.256608] systemd[1]: Started Restore /etc/resolv.conf if the system
> crashed before the ppp link was shut down..
> [ 9.283589] systemd[1]: Started LSB: start Samba daemons for the AD DC.
> [ 9.292391] systemd[1]: Started LSB: X display manager for KDE.
> [ 9.300175] systemd[1]: Started LSB: start Samba NetBIOS nameserver
> (nmbd). [ 9.309145] systemd[1]: Started LSB: keep memory of all UPnP
> devices that announced themselves.
> [ 9.319960] systemd[1]: Started LSB: Increased Performance In Linux With
> zRam (Virtual Swap Compressed in RAM).
> [ 9.332645] systemd[1]: Started LSB: emulates the RTC by setting the
> clock to the /var/log/syslog write time as early as possible.
> [ 9.346478] systemd[1]: Started Permit User Sessions.
> [ 9.353255] systemd[1]: Started Initialize hardware monitoring sensors.
> [ 9.363316] systemd[1]: Started System Logging Service.
> [ 9.369193] systemd[1]: Time has been changed
> [ 9.523728] systemd[1]: Starting Journal Socket (/dev/log).
> [ 9.530496] systemd-logind[310]: New seat seat0.
> [ 9.535523] systemd[1]: Listening on Journal Socket (/dev/log).
> [ 9.547881] systemd[1]: Starting LSB: Apache2 web server...
> [ 9.573220] systemd[1]: Starting LSB: Starts The Onion Router daemon
> processes...
> [ 9.584632] systemd[1]: Starting LSB: Start NTP daemon...
> [ 9.599503] systemd[1]: Starting LSB: network connection manager...
> [ 9.619870] systemd[1]: Starting LSB: Start the GNUstep distributed
> object mapper...
> [ 9.640153] systemd[1]: Starting LSB: Start and stop the mysql database
> server daemon...
> [ 9.679313] systemd[1]: Starting LSB: daemon to balance interrupts for
> SMP systems...
> [ 9.704125] systemd[1]: Starting LSB: 1-wire TCP server...
> [ 9.757257] systemd[1]: Starting LSB: start Samba SMB/CIFS daemon
> (smbd)... [ 9.875598] systemd[1]: Started LSB: network connection
> manager. [ 9.898121] systemd[1]: Started LSB: Start the GNUstep
> distributed object mapper.
> [ 9.930256] systemd[1]: Started LSB: start Samba SMB/CIFS daemon (smbd).
> [ 9.961973] systemd[1]: Started LSB: Start NTP daemon.
> [ 9.984443] systemd[1]: Started LSB: daemon to balance interrupts for SMP
> systems.
> [ 10.020608] systemd[1]: Started Login Service.
> [ 10.106476] systemd[1]: Starting Journal Socket.
> [ 10.112358] systemd[1]: Listening on Journal Socket.
> [ 10.118659] systemd[1]: Starting Journal Service...
> [ 10.138453] systemd[1]: Started Journal Service.
> [ 11.476933] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow
> control rx/tx
> [ 11.484699] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
> [ 11.992107] random: nonblocking pool is initialized
> [ 14.336848] systemd-logind[310]: New session c1 of user rd.
> [ 15.837136] usb 1-1: usbfs: process 827 (owfs) did not claim interface 0
> before use
> [ 15.846193] usb 1-1: usbfs: process 827 (owfs) did not claim interface 0
> before use
> [ 15.866108] usb 1-1: usbfs: process 827 (owfs) did not claim interface 0
> before use
> [ 15.882719] usb 1-1: usbfs: process 827 (owfs) did not claim interface 0
> before use
>
> Debian GNU/Linux 8 home ttymxc0
>
> home login:
>
>
>
> Looking at the differences, the new kernels seem to fail to mount the EXT4
> root filesystem:
>
> [ 3.295906] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data
> mode. Opts: (null)
>
> Kind regards
> Rainer
--
Rainer Dorsch
http://bokomoko.de/
Reply to: