debian's installer suspended !
hi !
I am in trouble with debian's installer suspending .
please give me some advise.
console's log s are as below.
==================================================================
U-Boot 1.1.4 (Sep 14 2009 - 15:36:37) Marvell version: 3.4.19
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00
Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM CS[1] base 0x10000000 size 256MB
DRAM Total size 512MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB
Flash: 0 kB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
Marvell>> mmcinit
Error! cmd : 8, err : 0201
SD found. Card desciption is:
Manufacturer: 0x01, OEM "PA"
Product name: "S128B", revision 5.6
Serial number: 2423100053
Manufacturing date: 10/2005
CRC: 0x00, b0 = 0
Marvell>> fatload mmc 0:1 0x0800000 /uInitrd
reading /uInitrd
2703032 bytes read
Marvell>> fatload mmc 0:1 0x400000 /uImage
reading /uImage
1811960 bytes read
Marvell>> setenv bootargs console=ttyS0,115200n8
base-installer/initramfs-tools/driver-policy=most
Marvell>> bootm 0x400000 0x0800000
## Booting image at 00400000 ...
Image Name: Debian kernel
Created: 2009-11-02 12:19:19 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1811896 Bytes = 1.7 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 00800000 ...
Image Name: debian-installer ramdisk
Created: 2009-11-02 12:19:20 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 2702968 Bytes = 2.6 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
Uncompressing
Linux....................................................................................................................
done, booting the kernel.
======================================================================================
env vars are as below.
Marvell>> printenv
baudrate=115200
loads_echo=0
rootpath=/mnt/ARM_FS/
netmask=255.255.0.0
console=a0000
e=ttyS0,115200
CASset=min
MALLOC_len=1
ethprime=egiga0
bootargs_root=root=/dev/mtdblock2 ro
ethmtu=1500
usb0Mode=host
nandEcc=1bit
ethact=egiga0
serverip=10.10.0.2
ipaddr=10.10.0.1
cesvcid=ULULULULULULPPULULULULULDA
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console)
root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end)
$(mvPhoneConfig); bootm 0x2000000;
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
yuk_ethaddr=00:00:00:EE:51:81
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
ethaddr=00:50:43:01:69:4D
run_diag=no
bootargs=console=ttyS0,115200
mtdparts=nand_mtd:0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs)
rw root=/dev/mtdblock1 rw
ip=10.4.50.4:10.4.50.5:10.4.50.5:255.255.255.0:DB88FXX81:eth0:none
bootcmd=nand read.e 0x800000 0x100000 0x400000; bootm 0x800000
mainlineLinux=yes
arcNumber=2097
stdin=serial
stdout=serial
stderr=serial
nandEnvBase=a0000
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
enaAutoRecovery=yes
pcieTune=no
Environment size: 1445/131068 bytes
best eregards,
m.azuma
Reply to: