[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Re: bast di install attempt

> Has anyone had any luck using DI to install on a bast ??
> I just tried the 20040820 DI rc1 install CD build, so far without
> success. I'm using a serial console, so used a variation of the
> ABLE commands given here:
> http://www.simtec.co.uk/products/EB2410ITX/faq.html#faqquestion_45
> (As an aside, the bast can load and run bootloader scripts directly
> from a local filesystem, so it would be nice to have the correct
> commands in a script somewhere on the DI install CD filesystem...).
> SuperIO controller fitted
> Initialising
> Detecting SDRAM size
> SDRAM: BANK6 size 04000000
> SDRAM: BANK7 size 04000000
> ABLE: 1.98 (bast,s3c2410x) (vince@gerald) Wed Jun  2 00:07:42 BST 2004
> System: Machine bast/s3c2410x, Linux id 0x014b
> Processor: Samsung S3C2410X (arm920) (0)
> =7FS3C2410X RTC: 23:39:45, 20/08/2004
> NAND: configured boot slot is 0 (card slot)
> EEPROM: 24cXX, 1024 bytes, single byte addressed
> (nvram0) on (24cxx)
> Setting CPU Speed to 203MHz
> no confiuration, defaulting to vga
> X/Y values invalid, configuring automatically
> Chrontel CH7006 detected
> screen mode is 640x480, ?Hz, ?Hz HSync
> video: video size 300K
> configuring ch7006: vga
> selected serial for console write stream
> selected serial for console read stream
> DRAM: 128 Mb (134217728 bytes)
> BAST: PMU version 1.02, ID 00:01:3d:00:01:04
> ABLE: 1.98 (bast,s3c2410x) (vince@gerald) Wed Jun  2 00:07:42 BST 2004
> hda: ATAPI CDROM: Slimtype DVD-ROM LSD-081
> (hda) 69MB
> (cd0) on ((hda1):iso9660)
> (rom0) on (nor0)
> DM9000: dm0: r0, 00:01:3d:00:01:04 int phy, link ok, 100Mbit half duplex
> NE2000: ne0: ISA/Generic, 00:01:3d:00:01:05 (EEPROM Invalid / Missing)
> sys.autoshadow unset, automatically shadowing
> boot.cmd unset, defaulting to '(cd0)install.sh'
> Autoboot in 8 seconds (attempt 1), Press any key to abort
> >
> >nvshow
> shell-hist (is unset)
> cons-write  =3D serial
> cons-read  =3D serial
> boot.auto (is unset)
> boot.cmd (is unset)
> boot.timeout  =3D 8
> ide.multi-limit (is unset)
> fb.enable (is unset)
> fb.output (is unset)
> fb.y (is unset)
> fb.x (is unset)
> sys.autoshadow (is unset)
> sys.speed  =3D 203
> >
> >setargs root=3D/dev/ram rw console=3DttySAC0,115200 s3c2410fb_disable=3D=
> >load (cd0)/install/bast/vmlinuz-2.4.25-bast (cd0)/install/bast/initrd.gz
> loaded (cd0)/install/bast/vmlinuz-2.4.25-bast, 0xfa69c bytes at 0x00008000
> loaded (cd0)/install/bast/initrd.gz, 0x14dbe9 bytes at 0x00408000
> >
> >boot
> boot: booting 'linux'
> Booting Linux
> Uncompressing Linux...............................................
> ........................... done, booting the kernel.
> (The early kernel messages seem to get garbled...)
> tts/AC%d%d0 at MMIO 0xd8800000 (irq =3D 70) is a S3C2410
> tts/AC%d%d1 at MMIO 0xd8804000 (irq =3D 73) is a S3C2410
> tts/AC%d%d2 at MMIO 0xd8808000 (irq =3D 76) is a S3C2410
> S3C2410 LCD/VGA Console support
> Console: switching to colour frame buffer device 80x60
> keyboard: Timeout - AT keyboard not present?(ed)
> keyboard: Timeout - AT keyboard not present?(f4)
> pty: 256 Unix98 ptys configured
> lp: driver loaded but no devices found
> Installing S3C2410 RTC
> S3C Real Time Clock driver v1.00
> ppdev: user-space parallel port driver
> S3C2410 Watchdog Timer: timer margin 20 sec
> RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
> bast-asix.c:v1.02 21/05/2003 D. Becker/P. Gortmaker/Ben Dooks
>   http://www.simtec.co.uk/products/EB2410ITX/
> net_bast_modinit: new device at c05dac00
> bast-asix.c:v1.02 21/05/2003 D. Becker/P. Gortmaker/Ben Dooks
>   http://www.simtec.co.uk/products/EB2410ITX/
> BAST Onboard NE2000 driver, (c) 2003 Simtec Electronics
> eth0: bast-ne2k found at 0xee400000, IRQ 55, 00:02:04:06:08:0A.
> BAST DM9000 Ethernet Driver, (c) 2003 Simtec Electronics
> eth1: bast-dm9000 found at 0xea500000, IRQ 54, 00:02:04:06:08:0A.
> Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
> ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=
> bast: IDE driver, (c) 2003 Simtec Electronics
>     ide0: at ee000100 (ee100000)
>     ide1: at ee200100 (ee300000)
> hda: Slimtype DVD-ROM LSD-081, ATAPI CD/DVD-ROM drive
> ide0 at 0xee000000-0xee000007,0xee1000c0 on irq 60
> tlv320aic23: (c) 2003 Simtec Electronics
> IISCON=3D0000002c, IISMOD=3D00000189, IISFCON=3D0000a000
> S3C2410: TLV320AIC23 / IIS initialized
> BAST Flash driver, (c) 2003 Simtec Electronics
> BAST flash mapped to c884d000
> Search for id:(08 ea00) interleave(1) type(2)
> Search for id:(bf 2782) interleave(1) type(2)
> Found: SST 39LF160
> BAST: Found 1 x16 devices at 0x0 in 16-bit mode
> number of JEDEC chips: 1
> No RedBoot partition table detected in BAST
> BAST Flash: Using none partition definition
> Creating -1071493716 MTD partitions on "BAST":
> usb.c: registered new driver usbdevfs
> usb.c: registered new driver hub
> usb: setting gbpcon=3D000a85aa
> usb: setting gbpdat=3D000002ef
> host/usb-ohci.c: USB OHCI at membase 0xd8200000, IRQ 42
> usb.c: new USB bus registered, assigned bus number 1
> Product: USB OHCI Root Hub
> SerialNumber: d8200000
> hub.c: USB hub found
> hub.c: 2 ports detected
> usb.c: registered new driver hiddev
> usb.c: registered new driver hid
> hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
> hid-core.c: USB HID support drivers
> usb.c: registered new driver usblp
> printer.c: v0.13: USB Printer Device Class driver
> usb.c: registered new driver usbnet
> usb.c: registered new driver serial
> usbserial.c: USB Serial Driver core v1.4
> usbserial.c: USB Serial support registered for FTDI SIO
> usbserial.c: USB Serial support registered for FTDI 8U232AM Compatible
> usbserial.c: USB Serial support registered for FTDI FT232BM Compatible
> usbserial.c: USB Serial support registered for USB-UIRT Infrared Receiver=
> usbserial.c: USB Serial support registered for Home-Electronics TIRA-1 IR=
> ftdi_sio.c: v1.3.5:USB FTDI Serial Converters Driver
> usbserial.c: USB Serial support registered for PL-2303
> pl2303.c: Prolific PL2303 USB to serial adaptor driver v0.10
> mice: PS/2 mouse device common for all mice
> NET4: Linux TCP/IP 1.0 for NET4.0
> IP: routing cache hash table of 1024 buckets, 8Kbytes
> TCP: Hash tables configured (established 8192 bind 8192)
> NetWinder Floating Point Emulator V0.97 (double precision)
> IrCOMM protocol (Dag Brattli)
> RAMDISK: Compressed image found at block 0
> Freeing initrd memory: 1334K
> VFS: Mounted root (ext2 filesystem).
> Freeing init memory: 100K
> Setting up filesystem, please wait ...
> Then nothing more from the serial port.
> The VGA port manages a flickering Tux, but nothing more.

you cammandlines are spot on btw, please consider adding to the docs?
or mailing the D-i team with a bug?

bugger...the new 2.4.27 kernels fix this but their stalled in new :-(
do you have a gold spec board? if so try using ttyS0 instead? you may
have to switch jumpers after using ABLE.

This is possibly because the d-i terminal program doesnt consider
ttySAC0 to be a serial port :-( Thers some devfs black magic

Alternately you can use the framebuffer and a usb keyboard, Its only
ABLE that doesnt do USB keyboards atm.

Regards Vincent

Attachment: signature.asc
Description: Digital signature

Reply to: