[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

bast di install attempt

Has anyone had any luck using DI to install on a bast ??

I just tried the 20040820 DI rc1 install CD build, so far without
success. I'm using a serial console, so used a variation of the
ABLE commands given here:


(As an aside, the bast can load and run bootloader scripts directly
from a local filesystem, so it would be nice to have the correct
commands in a script somewhere on the DI install CD filesystem...).

SuperIO controller fitted
Detecting SDRAM size
SDRAM: BANK6 size 04000000
SDRAM: BANK7 size 04000000
ABLE: 1.98 (bast,s3c2410x) (vince@gerald) Wed Jun  2 00:07:42 BST 2004
System: Machine bast/s3c2410x, Linux id 0x014b
Processor: Samsung S3C2410X (arm920) (0)
S3C2410X RTC: 23:39:45, 20/08/2004
NAND: configured boot slot is 0 (card slot)
EEPROM: 24cXX, 1024 bytes, single byte addressed
(nvram0) on (24cxx)
Setting CPU Speed to 203MHz
no confiuration, defaulting to vga
X/Y values invalid, configuring automatically
Chrontel CH7006 detected
screen mode is 640x480, ?Hz, ?Hz HSync
video: video size 300K
configuring ch7006: vga
selected serial for console write stream
selected serial for console read stream
DRAM: 128 Mb (134217728 bytes)
BAST: PMU version 1.02, ID 00:01:3d:00:01:04
ABLE: 1.98 (bast,s3c2410x) (vince@gerald) Wed Jun  2 00:07:42 BST 2004
hda: ATAPI CDROM: Slimtype DVD-ROM LSD-081
(hda) 69MB
(cd0) on ((hda1):iso9660)
(rom0) on (nor0)
DM9000: dm0: r0, 00:01:3d:00:01:04 int phy, link ok, 100Mbit half duplex
NE2000: ne0: ISA/Generic, 00:01:3d:00:01:05 (EEPROM Invalid / Missing)
sys.autoshadow unset, automatically shadowing
boot.cmd unset, defaulting to '(cd0)install.sh'
Autoboot in 8 seconds (attempt 1), Press any key to abort
shell-hist (is unset)
cons-write  = serial
cons-read  = serial
boot.auto (is unset)
boot.cmd (is unset)
boot.timeout  = 8
ide.multi-limit (is unset)
fb.enable (is unset)
fb.output (is unset)
fb.y (is unset)
fb.x (is unset)
sys.autoshadow (is unset)
sys.speed  = 203
>setargs root=/dev/ram rw console=ttySAC0,115200 s3c2410fb_disable=yes
>load (cd0)/install/bast/vmlinuz-2.4.25-bast (cd0)/install/bast/initrd.gz
loaded (cd0)/install/bast/vmlinuz-2.4.25-bast, 0xfa69c bytes at 0x00008000
loaded (cd0)/install/bast/initrd.gz, 0x14dbe9 bytes at 0x00408000
boot: booting 'linux'
Booting Linux
Uncompressing Linux...............................................
........................... done, booting the kernel.

(The early kernel messages seem to get garbled...)

tts/AC%d%d0 at MMIO 0xd8800000 (irq = 70) is a S3C2410
tts/AC%d%d1 at MMIO 0xd8804000 (irq = 73) is a S3C2410
tts/AC%d%d2 at MMIO 0xd8808000 (irq = 76) is a S3C2410
S3C2410 LCD/VGA Console support
Console: switching to colour frame buffer device 80x60
keyboard: Timeout - AT keyboard not present?(ed)
keyboard: Timeout - AT keyboard not present?(f4)
pty: 256 Unix98 ptys configured
lp: driver loaded but no devices found
Installing S3C2410 RTC
S3C Real Time Clock driver v1.00
ppdev: user-space parallel port driver
S3C2410 Watchdog Timer: timer margin 20 sec
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
bast-asix.c:v1.02 21/05/2003 D. Becker/P. Gortmaker/Ben Dooks
net_bast_modinit: new device at c05dac00
bast-asix.c:v1.02 21/05/2003 D. Becker/P. Gortmaker/Ben Dooks
BAST Onboard NE2000 driver, (c) 2003 Simtec Electronics
eth0: bast-ne2k found at 0xee400000, IRQ 55, 00:02:04:06:08:0A.
BAST DM9000 Ethernet Driver, (c) 2003 Simtec Electronics
eth1: bast-dm9000 found at 0xea500000, IRQ 54, 00:02:04:06:08:0A.
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
bast: IDE driver, (c) 2003 Simtec Electronics
    ide0: at ee000100 (ee100000)
    ide1: at ee200100 (ee300000)
hda: Slimtype DVD-ROM LSD-081, ATAPI CD/DVD-ROM drive
ide0 at 0xee000000-0xee000007,0xee1000c0 on irq 60
tlv320aic23: (c) 2003 Simtec Electronics
IISCON=0000002c, IISMOD=00000189, IISFCON=0000a000
S3C2410: TLV320AIC23 / IIS initialized
BAST Flash driver, (c) 2003 Simtec Electronics
BAST flash mapped to c884d000
Search for id:(08 ea00) interleave(1) type(2)
Search for id:(bf 2782) interleave(1) type(2)
Found: SST 39LF160
BAST: Found 1 x16 devices at 0x0 in 16-bit mode
number of JEDEC chips: 1
No RedBoot partition table detected in BAST
BAST Flash: Using none partition definition
Creating -1071493716 MTD partitions on "BAST":
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb: setting gbpcon=000a85aa
usb: setting gbpdat=000002ef
host/usb-ohci.c: USB OHCI at membase 0xd8200000, IRQ 42
usb.c: new USB bus registered, assigned bus number 1
Product: USB OHCI Root Hub
SerialNumber: d8200000
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
usb.c: registered new driver usblp
printer.c: v0.13: USB Printer Device Class driver
usb.c: registered new driver usbnet
usb.c: registered new driver serial
usbserial.c: USB Serial Driver core v1.4
usbserial.c: USB Serial support registered for FTDI SIO
usbserial.c: USB Serial support registered for FTDI 8U232AM Compatible
usbserial.c: USB Serial support registered for FTDI FT232BM Compatible
usbserial.c: USB Serial support registered for USB-UIRT Infrared Receiver/Transmitter
usbserial.c: USB Serial support registered for Home-Electronics TIRA-1 IR Transceiver
ftdi_sio.c: v1.3.5:USB FTDI Serial Converters Driver
usbserial.c: USB Serial support registered for PL-2303
pl2303.c: Prolific PL2303 USB to serial adaptor driver v0.10
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
NetWinder Floating Point Emulator V0.97 (double precision)
IrCOMM protocol (Dag Brattli)
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 1334K
VFS: Mounted root (ext2 filesystem).
Freeing init memory: 100K
Setting up filesystem, please wait ...

Then nothing more from the serial port.
The VGA port manages a flickering Tux, but nothing more.

Find what you are looking for with the Lycos Yellow Pages

Reply to: