ide module sis5513
hi there,
i have a problem with my motherboard in getting my sis ide controller running
in dma mode. the module is loaded but not used. i
modified /etc/mkinitrd/modules (see attachment) and built a new initrd by
mkinitrd. the rd-image is correctly set up in grub's menu.lst and loaded.
there seems to be some hassle with the generic driver but i don't know how to
remove the many ide-modules that are loaded at system startup since only
sis5513 mentioned in mkinitrd's modules as mentioned above. attached are some
snippets that might bring some light in the dark. i use the current stock 2.6
kernel (dmesg attached).
filou:~# lsmod
Module Size Used by
pktcdvd 30640 1
ipv6 262368 16
ehci_hcd 32004 0
snd_intel8x0 34624 0
snd_ac97_codec 80096 1 snd_intel8x0
snd_pcm 99916 2 snd_intel8x0,snd_ac97_codec
snd_timer 25032 1 snd_pcm
snd 57000 4 snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer
snd_page_alloc 11080 2 snd_intel8x0,snd_pcm
shpchp 94760 0
pci_hotplug 12292 1 shpchp
ohci_hcd 21640 0
i810_audio 36824 0
ac97_codec 20376 1 i810_audio
soundcore 11168 2 snd,i810_audio
r8169 21128 0
psmouse 21068 0
ide_cd 42336 1
cdrom 40040 2 pktcdvd,ide_cd
genrtc 10004 0
ext3 131216 2
jbd 57776 1 ext3
mbcache 9096 1 ext3
ide_generic 1600 0 [permanent]
via82cxxx 13552 0 [permanent]
trm290 4868 0 [permanent]
triflex 4480 0 [permanent]
slc90e66 6208 0 [permanent]
siimage 12736 0 [permanent]
serverworks 9296 0 [permanent]
sc1200 8128 0 [permanent]
rz1000 3136 0 [permanent]
piix 11140 0 [permanent]
pdc202xx_old 11968 0 [permanent]
opti621 4932 0 [permanent]
ns87415 4844 0 [permanent]
hpt366 20416 0 [permanent]
ide_disk 20224 6 hpt366
hpt34x 5824 0 [permanent]
generic 5248 0 [permanent]
cy82c693 5256 0 [permanent]
cs5530 6080 0 [permanent]
cs5520 5376 0 [permanent]
cmd64x 12172 0 [permanent]
atiixp 6032 0 [permanent]
amd74xx 14576 0 [permanent]
alim15x3 12504 0 [permanent]
aec62xx 7936 0 [permanent]
pdc202xx_new 9920 0 [permanent]
unix 29952 85
fbcon 37856 0
font 8960 1 fbcon
bitblit 6016 1 fbcon
vesafb 8804 0
cfbcopyarea 4288 1 vesafb
cfbimgblt 3200 1 vesafb
cfbfillrect 4160 1 vesafb
sis5513 14736 0 [permanent]
ide_core 146948 28
ide_cd,ide_generic,via82cxxx,trm290,triflex,slc90e66,siimage,serverworks,sc1200,rz1000,piix,pdc202xx_old,opti621,ns87415,hpt366,ide_disk,hpt34x,generic,cy82c693,cs5530,cs5520,cmd64x,atiixp,amd74xx,alim15x3,aec62xx,pdc202xx_new,sis5513
filou:~#
filou:~# lspci
0000:00:00.0 Host bridge: Silicon Integrated Systems [SiS] 760/M760 Host (rev
03)
0000:00:01.0 PCI bridge: Silicon Integrated Systems [SiS] SG86C202
0000:00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS965 [MuTIOL Media
IO] (rev 47)
0000:00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev
01)
0000:00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS]
Sound Controller (rev a0)
0000:00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.0
Controller (rev 0f)
0000:00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.0
Controller (rev 0f)
0000:00:03.2 USB Controller: Silicon Integrated Systems [SiS] USB 1.0
Controller (rev 0f)
0000:00:03.3 USB Controller: Silicon Integrated Systems [SiS] USB 2.0
Controller
0000:00:04.0 Ethernet controller: Silicon Integrated Systems [SiS]: Unknown
device 0190
0000:00:06.0 PCI bridge: Silicon Integrated Systems [SiS]: Unknown device 000a
0000:00:07.0 PCI bridge: Silicon Integrated Systems [SiS]: Unknown device 000a
0000:00:09.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169
Gigabit Ethernet (rev 10)
0000:00:0a.0 Unknown mass storage controller: Promise Technology, Inc. 20269
(rev 02)
0000:00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
0000:00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
0000:00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
0000:00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
0000:01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS]
661FX/M661FX/M661MX/741/M741/760/M760 PCI/AGP
filou:~# lspci -n
0000:00:00.0 0600: 1039:0760 (rev 03)
0000:00:01.0 0604: 1039:0002
0000:00:02.0 0601: 1039:0965 (rev 47)
0000:00:02.5 0101: 1039:5513 (rev 01)
0000:00:02.7 0401: 1039:7012 (rev a0)
0000:00:03.0 0c03: 1039:7001 (rev 0f)
0000:00:03.1 0c03: 1039:7001 (rev 0f)
0000:00:03.2 0c03: 1039:7001 (rev 0f)
0000:00:03.3 0c03: 1039:7002
0000:00:04.0 0200: 1039:0190
0000:00:06.0 0604: 1039:000a
0000:00:07.0 0604: 1039:000a
0000:00:09.0 0200: 10ec:8169 (rev 10)
0000:00:0a.0 0180: 105a:4d69 (rev 02)
0000:00:18.0 0600: 1022:1100
0000:00:18.1 0600: 1022:1101
0000:00:18.2 0600: 1022:1102
0000:00:18.3 0600: 1022:1103
0000:01:00.0 0300: 1039:6330
filou:~#
greetings
Uwe
--
-------------------------------
ASUS K8S-MX, 2800+ (754), 512MB, gnuLinux v2.6.x
# /etc/mkinitrd/modules: Kernel modules to load for initrd.
#
# This file should contain the names of kernel modules and their arguments
# (if any) that are needed to mount the root file system, one per line.
# Comments begin with a `#', and everything on the line after them are ignored.
#
# You must run mkinitrd(8) to effect this change.
#
# Examples:
#
# ext2
# wd io=0x300
sis5513
Bootdata ok (command line is root=/dev/hda1 ro )
Linux version 2.6.10-9-amd64-k8 (root@athlon.lowpingbastards.de) (gcc version 3.4.4 20050305 (prerelease) (Debian 3.4.3-11)) #1 Tue Mar 15 01:45:16 CET 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001dfd0000 (usable)
BIOS-e820: 000000001dfd0000 - 000000001dfdf000 (ACPI data)
BIOS-e820: 000000001dfdf000 - 000000001e000000 (ACPI NVS)
BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
No mptable found.
On node 0 totalpages: 122832
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 118736 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
ACPI: RSDP (v000 ACPIAM ) @ 0x00000000000fafb0
ACPI: RSDT (v001 A M I OEMRSDT 0x03000522 MSFT 0x00000097) @ 0x000000001dfd0000
ACPI: FADT (v002 A M I OEMFACP 0x03000522 MSFT 0x00000097) @ 0x000000001dfd0200
ACPI: MADT (v001 A M I OEMAPIC 0x03000522 MSFT 0x00000097) @ 0x000000001dfd0390
ACPI: OEMB (v001 A M I AMI_OEM 0x03000522 MSFT 0x00000097) @ 0x000000001dfdf040
ACPI: DSDT (v001 AH005 AH005001 0x00000001 INTL 0x02002026) @ 0x0000000000000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:4 APIC version 16
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 20, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Checking aperture...
CPU 0: aperture @ fc000000 size 32 MB
Aperture from northbridge cpu 0 too small (32 MB)
AGP bridge at 00:00:00
Aperture from AGP @ fc000000 size 32 MB (APSIZE f38)
Aperture from AGP bridge too small (32 MB)
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Mapping aperture over 65536 KB of RAM @ 4000000
Built 1 zonelists
Kernel command line: root=/dev/hda1 ro console=tty0
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 65536 bytes)
time.c: Using 1.193182 MHz PIT timer.
time.c: Detected 1804.021 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
Memory: 410096k/491328k available (1713k kernel code, 80468k reserved, 934k data, 140k init)
Calibrating delay loop... 3571.71 BogoMIPS (lpj=1785856)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 256 (order: 0, 4096 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: AMD Athlon(tm) 64 Processor 2800+ stepping 0a
Using local APIC NMI watchdog using perfctr0
Using local APIC timer interrupts.
Detected 12.527 MHz APIC timer.
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
NET: Registered protocol family 16
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20041105
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 7 10 11 12 14 15)
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas@hp.com
** so I can fix the driver.
PCI-DMA: Disabling IOMMU.
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
audit: initializing netlink socket (disabled)
audit(1112292519.143:0): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
Linux agpgart interface v0.100 (c) Dave Jones
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI wakeup devices:
PCI0 EUSB USB USB2 USB3 MAC AC97 MC97 P0P2
ACPI: (supports S0 S1 S3 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4152KiB [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 140k freed
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
SIS5513: IDE controller at PCI slot 0000:00:02.5
SIS5513: chipset revision 1
SIS5513: not 100% native mode: will probe irqs later
PDC20269: IDE controller at PCI slot 0000:00:0a.0
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 17
PDC20269: chipset revision 2
PDC20269: ROM enabled at 0xfebe0000
PDC20269: 100% native mode on irq 17
ide2: BM-DMA at 0xdc00-0xdc07, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xdc08-0xdc0f, BIOS settings: hdg:pio, hdh:pio
Probing IDE interface ide2...
hdf: LITE-ON LTR-24102B, ATAPI CD/DVD-ROM drive
elevator: using anticipatory as default io scheduler
ide2 at 0xec00-0xec07,0xe802 on irq 17
Probing IDE interface ide3...
hdg: HDS722525VLAT80, ATA DISK drive
ide3 at 0xe400-0xe407,0xe002 on irq 17
hdg: max request size: 1024KiB
hdg: 488397168 sectors (250059 MB) w/7938KiB Cache, CHS=30401/255/63, UDMA(100)
hdg: cache flushes supported
/dev/ide/host2/bus1/target0/lun0: p1
Probing IDE interface ide0...
hda: IC35L080AVVA07-0, ATA DISK drive
Probing IDE interface ide1...
Probing IDE interface ide4...
Probing IDE interface ide5...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 160836480 sectors (82348 MB) w/1863KiB Cache, CHS=65535/16/63
hda: cache flushes supported
/dev/ide/host0/bus0/target0/lun0: p1 p2
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 2289252k swap on /dev/hda2. Priority:-1 extents:1
EXT3 FS on hda1, internal journal
Generic RTC Driver v1.07
hdf: ATAPI 40X CD-ROM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdg1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
r8169 Gigabit Ethernet driver 1.2 loaded
ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 16 (level, low) -> IRQ 16
eth0: Identified chip type is 'RTL8169s/8110s'.
eth0: RTL8169 at 0xffffff0000134800, 00:11:6b:30:49:fb, IRQ 16
Intel 810 + AC97 Audio, version 1.01, 02:24:59 Mar 15 2005
ACPI: PCI interrupt 0000:00:02.7[C] -> GSI 18 (level, low) -> IRQ 18
i810: SiS 7012 found at IO 0xd400 and 0xd800, MEM 0x0000 and 0x0000, IRQ 18
i810_audio: Audio Controller supports 6 channels.
i810_audio: Defaulting to base 2 channel mode.
i810_audio: Resetting connection 0
ac97_codec: AC97 Audio codec, id: ADS104 (Unknown)
i810_audio: AC'97 codec 0 supports AMAP, total channels = 6
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 20
ohci_hcd 0000:00:03.0: Silicon Integrated Systems [SiS] USB 1.0 Controller
ohci_hcd 0000:00:03.0: irq 20, pci mem 0xfebf4000
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ACPI: PCI interrupt 0000:00:03.1[B] -> GSI 21 (level, low) -> IRQ 21
ohci_hcd 0000:00:03.1: Silicon Integrated Systems [SiS] USB 1.0 Controller (#2)
ohci_hcd 0000:00:03.1: irq 21, pci mem 0xfebf5000
ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ACPI: PCI interrupt 0000:00:03.2[C] -> GSI 22 (level, low) -> IRQ 22
ohci_hcd 0000:00:03.2: Silicon Integrated Systems [SiS] USB 1.0 Controller (#3)
ohci_hcd 0000:00:03.2: irq 22, pci mem 0xfebf6000
ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Evaluate _OSC Set fails. Status = 0x0005
pciehp: add_host_bridge: status 5
pciehp: Fails to gain control of native hot-plug
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ACPI: PCI interrupt 0000:00:03.3[D] -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:03.3: Silicon Integrated Systems [SiS] USB 2.0 Controller
ehci_hcd 0000:00:03.3: irq 23, pci mem 0xfebf7000
ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 4
PCI: cache line size of 64 is not supported by device 0000:00:03.3
ehci_hcd 0000:00:03.3: USB 2.0 initialized, EHCI 1.00, driver 26 Oct 2004
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 8 ports detected
Evaluate _OSC Set fails. Status = 0x0005
pciehp: add_host_bridge: status 5
pciehp: Fails to gain control of native hot-plug
Evaluate _OSC Set fails. Status = 0x0005
pciehp: add_host_bridge: status 5
pciehp: Fails to gain control of native hot-plug
r8169: eth0: link up
NET: Registered protocol family 10
Disabled Privacy Extensions on device ffffffff80364fc0(lo)
IPv6 over IPv4 tunneling driver
pktcdvd: v0.2.0a 2004-07-14 Jens Axboe (axboe@suse.de) and petero2@telia.com
cdrom: This disc doesn't have any tracks I recognize!
pktcdvd: writer pktcdvd0 mapped to hdf
eth0: no IPv6 routers present
Reply to: