[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Re: 2.4.18 kernel hang using Symbios driver



----- Original Message -----
From: "sousa jack" <sousa_jack@yahoo.com>
Subject: Re: 2.4.18 kernel hang using Symbios driver


> Is the SCSI card plugged into one of the 64-bit slots?

There are no 64 bit slots on a Cabriolet, only 32 bit.

Rob

>
> --- Rob Byrnes <robbyrnes@ozemail.com.au> wrote:
> > ----- Original Message -----
> > From: "Jay Estabrook" <Jay.Estabrook@compaq.com>
> > Subject: Re: 2.4.18 kernel hang using Symbios driver
> >
> >
> > > On Wed, May 01, 2002 at 04:07:19PM +1000, Rob
> > Byrnes wrote:
> > > >
> > > > Has anyone else had problems booting a 2.4.18
> > kernel with the SYM53C8XX
> > > > driver?
> > > >
> > > > I have a Cabriolet running Woody, and while
> > kernel 2.2.20 with the same
> > the
> > > > driver loads up fine, I get SCSI RESET error
> > messages and then a hang
> > while
> > > > trying to boot into 2.4.18.  The SCSI card is a
> > Tekram DC 390U.
> > > >
> > > > I have also tried the "generic" NCR53C8XX driver
> > with identical results.
> > >
> > > Any chance you could provide us with the bootlog
> > of the failure?
> > >
> > > Many things have changed between 2.2.20 and
> > 2.4.18, and a log may give
> > > us some hints as to what might have gone wrong...
> >
> > Well, here is what comes up on the screen during
> > boot:
> >
> > <snip>
> > SCSI subsystem driver Revision: 1.00
> > sym.0.5.0: setting PCI_COMMAND_INVALIDATE.
> > sym0: <875> rev 0x1 on pci bus 0 device 5 function 0
> > irq 23
> > sym0: Tekram NVRAM, ID 7, Fast-20, SE, parity
> > checking
> > sym0: SCSI bus has been reset.
> > scsi0 : sym-2.1.17a
> > sym0:0:0: ABORT operation started.
> > sym0:0:0: ABORT operation timed out.
> > sym0:0:0: DEVICE RESET operation started.
> > sym0:0:0: DEVICE RESET operation timed out.
> > sym0:0:0: BUS RESET operation started.
> > sym0:0:0: BUS RESET operation timed out.
> > sym0:0:0: HOST RESET operation started.
> > sym0: SCSI bus has been reset
> >
> > The boot sequence hangs at this point.  I don't know
> > why the bus is being
> > reset either.
> >
> > Cheers,
> > Rob
> >
> >
> > --
> > To UNSUBSCRIBE, email to
> > debian-alpha-request@lists.debian.org
> > with a subject of "unsubscribe". Trouble? Contact
> > listmaster@lists.debian.org
> >
>
>
> __________________________________________________
> Do You Yahoo!?
> Yahoo! Health - your guide to health and wellness
> http://health.yahoo.com
>
>
> --
> To UNSUBSCRIBE, email to debian-alpha-request@lists.debian.org
> with a subject of "unsubscribe". Trouble? Contact
listmaster@lists.debian.org
>


-- 
To UNSUBSCRIBE, email to debian-alpha-request@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org



Reply to: