Re: X problem
>>> "Christopher C. Chimelis" <chris@debian.org> 09/29/00 01:29pm >>>
>I have an identical vid board on an SX and I have no problems (just
>reassurance). FYI, it's not good to probe most S3 cards and make sure
>that you don't have a clocks line. Below is my config...see if it works
>for you (it should). You may want to comment out the last few lines
>(utah-glx crap) if you don't have that installed. I admit it's a bit
>large, but I just haven't had the chance to trim it down yet.....
Unfortunatelly it does not work with your XF86Config file. The same effect, the screen changes to graphics mode but stays black and the machine crashes. Rermoving the module and forcing 640*480 8bpp does not change anything.
I get the following output starting XF86_S3:
XFree86 Version 3.3.6 / X Window System
(protocol Version 11, revision 0, vendor release 6300)
Release Date: January 8 2000
If the server is older than 6-12 months, or if your card is newer
than the above date, look for a newer version before reporting
problems. (see http://www.XFree86.Org/FAQ)
Operating System: Linux 2.2.16 alpha [ELF]
Configured drivers:
S3: accelerated server for S3 graphics adaptors (Patchlevel 0)
newmmio, mmio_928, s3_generic
(using VT number 7)
XF86Config: /usr/X11R6/lib/X11/XF86Config
(**) stands for supplied, (--) stands for probed/default values
(**) XKB: keymap: "xfree86(us)" (overrides other XKB settings)
(**) Mouse: type: PS/2, device: /dev/psaux, buttons: 3
(**) S3: Graphics device ID: "Mine"
(**) S3: Monitor ID: "IBM"
(--) S3: Mode "640x480" needs hsync freq of 53.01 kHz. Deleted.
(--) S3: Mode "1152x864" needs hsync freq of 53.51 kHz. Deleted.
(--) S3: Mode "800x600" needs hsync freq of 55.84 kHz. Deleted.
(--) S3: Mode "1024x768" needs hsync freq of 56.48 kHz. Deleted.
(--) S3: Mode "1280x1024" needs hsync freq of 51.02 kHz. Deleted.
(--) S3: Mode "800x600" needs hsync freq of 64.02 kHz. Deleted.
(--) S3: Mode "1024x768" needs hsync freq of 62.50 kHz. Deleted.
(--) S3: Mode "1152x864" needs hsync freq of 62.42 kHz. Deleted.
(--) S3: Mode "1280x1024" needs hsync freq of 64.25 kHz. Deleted.
(--) S3: Mode "1024x768" needs hsync freq of 70.24 kHz. Deleted.
(--) S3: Mode "1152x864" needs hsync freq of 70.88 kHz. Deleted.
(--) S3: Mode "1280x1024" needs hsync freq of 74.59 kHz. Deleted.
(--) S3: Mode "1600x1200" needs hsync freq of 75.00 kHz. Deleted.
(--) S3: Mode "1152x864" needs hsync freq of 76.01 kHz. Deleted.
(--) S3: Mode "1280x1024" needs hsync freq of 78.86 kHz. Deleted.
(--) S3: Mode "1024x768" needs hsync freq of 80.21 kHz. Deleted.
(--) S3: Mode "1280x1024" needs hsync freq of 81.13 kHz. Deleted.
(--) S3: Mode "1600x1200" needs hsync freq of 87.50 kHz. Deleted.
(--) S3: Mode "1152x864" needs hsync freq of 89.62 kHz. Deleted.
(--) S3: Mode "1280x1024" needs hsync freq of 91.15 kHz. Deleted.
(--) S3: Mode "1600x1200" needs hsync freq of 93.75 kHz. Deleted.
(--) S3: Mode "1600x1200" needs hsync freq of 105.77 kHz. Deleted.
(--) S3: Mode "1280x1024" needs hsync freq of 107.16 kHz. Deleted.
(--) S3: Mode "1800X1440" needs hsync freq of 96.15 kHz. Deleted.
(--) S3: Mode "1800X1440" needs hsync freq of 104.52 kHz. Deleted.
(--) no ModulePath specified using default: /usr/X11R6/lib/modules
glx.so: Unknown error loading module
(**) FontPath set to "/usr/X11R6/lib/X11/fonts/misc/,/usr/X11R6/lib/X11/fonts/75
dpi/:unscaled,/usr/X11R6/lib/X11/fonts/75dpi/"
(--) S3: PCI: Trio32/64 rev 0, Linear FB @ 0x04800000
(--) S3: chipset: Trio64 rev. 20
(--) S3: chipset driver: mmio_928
(--) S3: card type: PCI
(**) S3: videoram: 2048k
(--) S3: Ramdac type: s3_trio64
(--) S3: Ramdac speed: 135 MHz
(--) S3: Using Trio32/64 programmable clock (MCLK 57.273 MHz)
(--) S3: Maximum allowed dot-clock: 50.000 MHz
(**) S3: Mode "800x600": mode clock = 50.000
(**) S3: Mode "640x480": mode clock = 36.000
(**) S3: Using sparse 32 bpp. Color weight: 888
(--) S3: Virtual resolution set to 800x600
Reply to: