Re: startsec problem?
OK, I have built cdrecord from this source:
ftp://ftp.berlios.de/pub/cdrecord/cdrtools-2.01.tar.bz2
and I have changed the drive specification in /etc/default/cdrecord to
ATA:0,1,0. I read 2 known-good pressed audio CD with official readcd
-clone and wrote them with official cdrecord -clone. Both times I got the
same error, which is the same as with the unofficial Debian version. The
coasters produced cause the drive to take too long when trying to cdrecord
-toc or cdrecord -atip, and the bus is reset, and DMA turned off. Here is
the output of cdrecord:
$ sudo ./official/cdrtools-2.01/cdrecord/OBJ/i686-linux-cc/cdrecord -v -clone -raw96r cdimage
Cdrecord-Clone 2.01 (i686-pc-linux-gnu) Copyright (C) 1995-2004 Jörg Schilling
./official/cdrtools-2.01/cdrecord/OBJ/i686-linux-cc/cdrecord: Warning: Running on Linux-2.6.15-1-686
./official/cdrtools-2.01/cdrecord/OBJ/i686-linux-cc/cdrecord: There are unsettled issues with Linux-2.5 and newer.
./official/cdrtools-2.01/cdrecord/OBJ/i686-linux-cc/cdrecord: If you have unexpected problems, please try Linux-2.4 or Solaris.
TOC Type: 1 = CD-ROM
scsidev: 'ATA:0,1,0'
devname: 'ATA'
scsibus: 0 target: 1 lun: 0
Warning: Using badly designed ATAPI via /dev/hd* interface.
Linux sg driver version: 3.5.27
Using libscg version 'schily-0.8'.
Driveropts: '"burnfree"'
SCSI buffer size: 64512
atapi: -1
Device type : Removable CD-ROM
Version : 0
Response Format: 3
Capabilities :
Vendor_info : 'PLEXTOR '
Identifikation : 'DVDR PX-740A '
Revision : '1.00'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x0009
Profile: 0x002B
Profile: 0x001B
Profile: 0x001A
Profile: 0x0016
Profile: 0x0015
Profile: 0x0014
Profile: 0x0011
Profile: 0x0010
Profile: 0x000A
Profile: 0x0009 (current)
Profile: 0x0008
./official/cdrtools-2.01/cdrecord/OBJ/i686-linux-cc/cdrecord: This version of cdrecord does not include DVD-R/DVD-RW support code.
./official/cdrtools-2.01/cdrecord/OBJ/i686-linux-cc/cdrecord: If you need DVD-R/DVD-RW support, ask the Author for cdrecord-ProDVD.
./official/cdrtools-2.01/cdrecord/OBJ/i686-linux-cc/cdrecord: Free test versions and free keys for personal use are at ftp://ftp.berlios.de/pub/cdrecord/ProDVD/
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96R RAW/R16 RAW/R96R
Drive buf size : 1073152 = 1048 KB
FIFO size : 4194304 = 4096 KB
Encoding speed : 126x (9440 sectors/s) for libedc from Heiko Eißfeldt
Track 01: data 513 MB
Total size: 492 MB (48:50.13) = 219760 sectors
Lout start: 493 MB (48:52/10) = 219760 sectors
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 4
Is not unrestricted
Is not erasable
Disk sub type: Medium Type A, high Beta category (A+) (3)
ATIP start of lead in: -11849 (97:24/01)
ATIP start of lead out: 359847 (79:59/72)
Disk type: Long strategy type (Cyanine, AZO or similar)
Manuf. index: 25
Manufacturer: Taiyo Yuden Company Limited
Blocks total: 359847 Blocks current: 359847 Blocks remaining: 140087
Starting to write CD/DVD at speed 48 in real RAW/RAW96R mode for single session.
Last chance to quit, starting real write 0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
BURN-Free is ON.
Turning BURN-Free off
Performing OPC...
./official/cdrtools-2.01/cdrecord/OBJ/i686-linux-cc/cdrecord: WARNING: Drive returns wrong startsec (0) using -11849 from ATIP
Writing lead-in at sector -11849
Lead-in write time: 12.945s
Writing pregap for track 1 at -150
Starting new track at sector: 0
Track 01: 513 of 513 MB written (fifo 100%) [buf 91%] 41.7x.
Track 01: Total bytes read/written: 537972480/537972480 (219760 sectors).
Writing time: 115.883s
Average write speed 28.5x.
Min drive buffer fill was 86%
Writing Leadout...
Fixating...
Fixating time: 39.324s
./official/cdrtools-2.01/cdrecord/OBJ/i686-linux-cc/cdrecord: fifo had 8453 puts and 8453 gets.
./official/cdrtools-2.01/cdrecord/OBJ/i686-linux-cc/cdrecord: fifo was 0 times empty and 3831 times full, min fill was 92%.
Alexey
Reply to: