perplexed by cdwrite prodvd errors
Hello--
I am having quite a lot of trouble with cdrecord-prodvd.
I would like to use it instead of growisofs, because I am trying to
produce a dvd-video with high compatibility with standalone readers, and
so want to use DAO.
I believe my system & hardware is ok, because growisofs works fine for
making the same dvd.
Could somebody please point me in the right direction concerning all
these errors ?
Thanks very much,
--Sam
[root@damballah root]# ./cdrecord-wrapper.sh
Cdrecord-ProDVD-Clone 2.01b31 (i686-pc-linux-gnu) Copyright (C)
1995-2004 J?rg Schilling
Unlocked features: ProDVD Clone
Limited features:
This copy of cdrecord is licensed for:
private/research/educational_non-commercial_use
TOC Type: 1 = CD-ROM
scsidev: '0,0,0'
scsibus: 0 target: 0 lun: 0
Linux sg driver version: 3.1.24
Using libscg version 'schily-0.8'.
Driveropts: 'burnfree'
SCSI buffer size: 64512
atapi: 1
Device type : Removable CD-ROM
Version : 0
Response Format: 2
Capabilities :
Vendor_info : '_NEC '
Identifikation : 'DVD_RW ND-1300A '
Revision : '1h05'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: DVD-R sequential recording
Profile: DVD+R
Profile: DVD+RW
Profile: DVD-RW sequential overwrite
Profile: DVD-RW restricted overwrite
Profile: DVD-R sequential recording (current)
Profile: DVD-ROM
Profile: CD-RW
Profile: CD-R
Profile: CD-ROM
Using generic SCSI-3/mmc-2 DVD-R/DVD-RW driver (mmc_dvd).
Driver flags : DVD MMC-3 SWABAUDIO BURNFREE
Supported modes: PACKET SAO
Drive buf size : 1605632 = 1568 KB
FIFO size : 4194304 = 4096 KB
pregap1: -1
Track 01: data 212 MB padsize: 30 KB
Total size: 212 MB = 109039 sectors
Current Secsize: 2048
Blocks total: 2298496 Blocks current: 2298496 Blocks remaining: 2189457
Starting to write CD/DVD at speed 2 in dummy SAO mode for single session.
Last chance to quit, starting dummy write 0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
BURN-Free is ON.
Starting new track at sector: 0
Track 01: 7 of 212 MB written (fifo 98%) [buf 100%]
2.9x./root/cdrecord-prodvd-2.01b31-i686-pc-linux-gnu: Input/output
error. write_g1: scsi sendcmd:
no error
CDB: 2A 00 00 00 0E 88 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0A 00 00 00 00 21 02 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x21 Qual 0x02 (invalid address for write) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.032s timeout 100s
write track data: error after 7618560 bytes
/root/cdrecord-prodvd-2.01b31-i686-pc-linux-gnu: The current problem
looks like a buffer underrun.
/root/cdrecord-prodvd-2.01b31-i686-pc-linux-gnu: It looks like
'driveropts=burnfree' does not work for this drive.
/root/cdrecord-prodvd-2.01b31-i686-pc-linux-gnu: Please report.
/root/cdrecord-prodvd-2.01b31-i686-pc-linux-gnu: Make sure that you are
root, enable DMA and check your HW/OS set up.
Writing time: 45.594s
Average write speed 3.5x.
Min drive buffer fill was 100%
Fixating...
/root/cdrecord-prodvd-2.01b31-i686-pc-linux-gnu: Input/output error.
flush cache: scsi sendcmd: no error
CDB: 35 00 00 00 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 06 00 00 00 00 0A 00 00 00 00 29 00 00 00
Sense Key: 0x6 Unit Attention, Segment 0
Sense Code: 0x29 Qual 0x00 (power on, reset, or bus device reset
occurred) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 27.150s timeout 1000s
Trouble flushing the cache
Fixating time: 27.151s
BURN-Free was not used.
/root/cdrecord-prodvd-2.01b31-i686-pc-linux-gnu: fifo had 184 puts and
121 gets.
/root/cdrecord-prodvd-2.01b31-i686-pc-linux-gnu: fifo was 0 times empty
and 57 times full, min fill was 95%.
Reply to: