Re: cdrecord problems with TDK 440n DVD+/-rw
>From: Dan <overridex@punkass.com>
> I'm having problems burning cds with my TDK 440n DVD+/-rw drive,
>burning dvds with growisofs works fine. It's not the drive's hardware,
>as I've tested burning cds in windows on another box and it's working
>ok. Burning cds with cdrecord did work in the past, but I've since
>updated cdrecord, updated my kernel from 2.4.x to 2.6.x, changed from
>ide-scsi to atapi, and updated the drives firmware before i noticed cd
>burning wasn't working any more, so it's hard to track down what the
>problem is, below is the output of dmesg when burning followed by
>cdrecord's output. Please CC me any replies as I'm not subscribed to
>the list, thanks everyone!
>dmesg:
>hdc: status error: error=0x04Aborted Command
>hdc: drive not ready for command
>hdc: ATAPI reset complete
>cdrecord:
>cdrecord: No write mode specified.
>cdrecord: Asuming -tao mode.
>cdrecord: Future versions of cdrecord may have different drive
>de pendent
>defaults.
>cdrecord: Continuing in 5 seconds...
>Cdrecord-Clone 2.01a32 (i686-pc-linux-gnu) Copyright (C)
>1995-200 4 Jörg
>Schilling
>scsidev: 'ATAPI:0,0,0'
>devname: 'ATAPI'
>scsibus: 0 target: 0 lun: 0
>Warning: Using ATA Packet interface.
>Warning: The related Linux kernel interface code seems to be
>unma intained.
>Warning: There is absolutely NO DMA, operations thus are slow.
>Using libscg version 'schily-0.8'.
>Device type : Removable CD-ROM
>Version : 0
>Response Format: 2
>Capabilities :
>Vendor_info : 'TDK '
>Identifikation : 'DVDRW0404N '
>Revision : '1.0A'
>Device seems to be: Generic mmc2 DVD-R/DVD-RW.
>cdrecord: This version of cdrecord does not include
>DVD-R/DVD-RW
>support code.
>cdrecord: If you need DVD-R/DVD-RW support, ask the Author for
>cd record-ProDVD.
>cdrecord: Free test versions and free keys for personal use are
>a t
>ftp://ftp.berlios.de/pub/cdrecord/ProDVD/
>Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
>Driver flags : MMC-3 SWABAUDIO BURNFREE
>Supported modes: TAO PACKET SAO SAO/R96R RAW/R96R
>Starting to write CD/DVD at speed 4 in real TAO mode for single
>s ession.
>Last chance to quit, starting real write 0 seconds.
>Operation starts.
>Turning BURN-Free off
>cdrecord: faio_wait_on_buffer for writer timed out.
>cdrecord: Input/output error. write_g1: scsi sendcmd: no error
>CDB: 2A 00 00 00 00 00 00 00 1F 00
>status: 0x0 (GOOD STATUS)
>cmd finished after 400.213s timeout 40s
>write track data: error after 0 bytes
>cdrecord: A write error occured.
>cdrecord: Please properly read the error message above.
>cdrecord: Input/output error. test unit ready: scsi sendcmd:
>retr yable error
>CDB: 00 00 00 00 00 00
>status: 0xa (Reserved)
>Sense Bytes: 70 00 02 00 00 00 00 0A 00 00 00 00 04 01 00 80 26
>6 6
>Sense Key: 0x2 Not Ready, Segment 0
>Sense Code: 0x04 Qual 0x01 (logical unit is in process of
>becomin g ready)
>Fru 0x0
>Sense flags: Blk 0 (not valid) operation 14% done
>cmd finished after 0.006s timeout 40s
Looks like you have another unfriendly application running that
tries simultanous access to the drive :-(
Jörg
--
EMail:joerg@schily.isdn.cs.tu-berlin.de (home) Jörg Schilling D-13353 Berlin
js@cs.tu-berlin.de (uni) If you don't have iso-8859-1
schilling@fokus.fraunhofer.de (work) chars I am J"org Schilling
URL: http://www.fokus.fraunhofer.de/usr/schilling ftp://ftp.berlios.de/pub/schily
Reply to: