Re: Problem using a TEAC DV-W22E with dvd+rw-tools/cdrecord-prodvd/dvdrtools.
>>I am using a TEAC DV-W22E R.0A on my notebook, which is a all in one
>>CD-R/RW and DVD-R/RW player and writer. My main OS is FreeBSD 5.2.1
>>(RELEASE-p4) and I already succeed in:
>>
>> - write CD-R (cdrecord);
>> - write/rewrite CD-RW (cdrecord);
>> - write a DVD-R (growisofs).
>>
>>But it seems _not_possible_ to write (or rewrite or blank etc.) a DVD-RW.
>>Here is the exact version of software I try to use:
>> # portversion -v | grep -i "dvd+rw-tools"
>> dvd+rw-tools-5.19.4.9.7
>> # cdrecord -version
>> Cdrecord 2.00.3 (i386-unknown-freebsd5.2.1) Copyright (C) 1995-2002 Jörg
>> Schilling
>> # cdrecord-prodvd -version
>> Cdrecord-ProDVD-Clone 2.01a24 (i386-unknown-freebsd5.2) Copyright (C)
>> 1995-2004 Jörg Schilling
>> # dvdrtools -version
> It does not seem that you really used cdrecord-ProDVD!
> If you don't use it and give error messages, it is hard to help
Ok, sorry for the _bad_ information. Here is what I get if I try to use
cdrecord-ProDVD (obtained from ftp://ftp.berlios.de/pub/cdrecord/ProDVD/
cdrecord-prodvd-2.01a24-i386-unknown-freebsd5.2), see below.
> It is absolutely not recommended to format DVD-RW media.
I try to put a DVD-RW in the restricted overwrite format, this is why I
try (wihout success) to format it using:
# dvd+rw-format /dev/cd0
> If you ever did format it, you _need_ to run cdrecord blank=full
> to make it usable again.
I get the following error trying to blank the DVD-RW media:
# ./cdrecord-wrapper.sh -v -blank=all dev=3,0,0
Cdrecord-ProDVD-Clone 2.01a24 (i386-unknown-freebsd5.2) Copyright (C)
1995-2004 Jörg Schilling
Unlocked features: ProDVD Clone
Limited features:
This copy of cdrecord is licensed for:
private/research/educational_non-commercial_use
TOC Type: 1 = CD-ROM
scsidev: '3,0,0'
scsibus: 3 target: 0 lun: 0
Using libscg version 'schily-0.8'.
SCSI buffer size: 64512
atapi: 0
Device type : Removable CD-ROM
Version : 0
Response Format: 2
Capabilities :
Vendor_info : 'TEAC '
Identifikation : 'DV-W22E '
Revision : 'R.0A'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: DVD-RW sequential overwrite
Profile: DVD-RW sequential overwrite (current)
Profile: DVD-RW restricted overwrite
Profile: DVD-R sequential recording
Profile: DVD-ROM
Profile: CD-RW
Profile: CD-R
Profile: CD-ROM
Using generic SCSI-3/mmc-2 DVD-R/DVD-RW driver (mmc_dvd).
Driver flags : DVD MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R
Drive buf size : 1441792 = 1408 KB
Current Secsize: 2048
cdrecord-ProDVD: Input/output error. read track info: scsi sendcmd:
retryable error
CDB: 52 00 00 00 00 00 00 00 24 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00
Sense Key: 0xFFFFFFFF [], Segment 0
Sense Code: 0x00 Qual 0x00 (no additional sense information) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.000s timeout 240s
WARNING: Phys disk size 2298496 differs from rzone size 0! Prerecorded disk?
WARNING: Phys start: 196608 Phys end 2495103
Starting to write CD/DVD at speed 1 in real BLANK mode for single session.
Last chance to quit, starting real write 0 seconds. Operation starts.
Blanking entire disk
cdrecord-ProDVD: Input/output error. blank unit: scsi sendcmd: retryable
error
CDB: A1 00 00 00 00 00 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00
Sense Key: 0xFFFFFFFF [], Segment 0
Sense Code: 0x00 Qual 0x00 (no additional sense information) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 172.897s timeout 9600s
cdrecord-ProDVD: Cannot blank disk, aborting.
Am I doing something wrong or is my TEAC DV-W22E writer the problem (not
supported, etc.)? Don't hesitate to ask for some other command's output.
Since I am new to DVD recording, maybe I don't know the best information
that might help you to diagnose the origin of this problem.
> Note that the program called "dvdrecord" is an illegal program RedHat
> that does not work.
Ok.
Thanks for your help,
--
-jpeg.
Reply to: