Re: Problems with USB in my Acer Travelmate
Hi again,
I have reconfigured my kernel 2.4.26 using ACPI
support.
dmesg output,
Linux version 2.4.26 (root@viggen) (gcc version 2.95.4
20011002 (Debian prerelease)) #14 SMP Thu Jul 8
11:44:35 CEST 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00
(usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000
(reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000
(reserved)
BIOS-e820: 0000000000100000 - 000000001eff0000
(usable)
BIOS-e820: 000000001eff0000 - 000000001effffc0 (ACPI
data)
BIOS-e820: 000000001effffc0 - 000000001f000000 (ACPI
NVS)
BIOS-e820: 00000000ffb80000 - 00000000ffc00000
(reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000
(reserved)
495MB LOWMEM available.
On node 0 totalpages: 126960
zone(0): 4096 pages.
zone(1): 122864 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 OID_00
) @ 0x000e6010
ACPI: RSDT (v001 INSYDE RSDT_000 0x00000001 _CSI
0x00010101) @ 0x1effa5b0
ACPI: FADT (v001 COMPAL DCL51_00 0x00000100 _CSI
0x00010101) @ 0x1efffb00
ACPI: BOOT (v001 INSYDE BOOT_000 0x00000001 _CSI
0x00010101) @ 0x1efffb90
ACPI: DBGP (v001 INSYDE DBGP_000 0x00000001 _CSI
0x00010101) @ 0x1efffbc0
ACPI: SSDT (v001 INSYDE GV3Ref 0x00002000 INTL
0x20021002) @ 0x1effa5f0
ACPI: DSDT (v001 ACER TM290 0x00000006 MSFT
0x0100000e) @ 0x00000000
Kernel command line: BOOT_IMAGE=Linux-2.4.26 ro
root=302
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
Detected 1398.828 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 2791.83 BogoMIPS
Memory: 498588k/507840k available (1895k kernel code,
8864k reserved, 909k data, 132k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7,
524288 bytes)
Inode cache hash table entries: 32768 (order: 6,
262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096
bytes)
Buffer cache hash table entries: 32768 (order: 5,
131072 bytes)
Page-cache hash table entries: 131072 (order: 7,
524288 bytes)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: a7e9fbbf 00000000
00000000 00000000
CPU: Common caps: a7e9fbbf 00000000
00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: a7e9fbbf 00000000
00000000 00000000
CPU: Common caps: a7e9fbbf 00000000
00000000 00000000
CPU0: Intel(R) Pentium(R) M processor 1400MHz stepping
05
per-CPU timeslice cutoff: 2927.35 usecs.
SMP motherboard not detected.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1398.8556 MHz.
..... host bus clock speed is 99.9180 MHz.
cpu: 0, clocks: 999180, slice: 499590
CPU0<T0:999168,T1:499568,D:10,S:499590,C:999180>
Waiting on wait_init_idle (map = 0x0)
All processors have done init_idle
ACPI: Subsystem revision 20040326
PCI: PCI BIOS revision 2.10 entry at 0xe9824, last
bus=1
PCI: Using configuration type 1
tbxface-0117 [03] acpi_load_tables : ACPI Tables
successfully acquired
Parsing all Control
Methods:............................................................................................................................................................................................
Table [DSDT](id F005) - 618 Objects with 53 Devices
188 Methods 20 Regions
Parsing all Control Methods:....
Table [SSDT](id F003) - 7 Objects with 0 Devices 4
Methods 0 Regions
ACPI Namespace successfully loaded at root c04169fc
ACPI: IRQ9 SCI: Edge set to Level Trigger.
evxfevnt-0093 [04] acpi_enable : Transition
to ACPI mode successful
evgpeblk-0867 [06] ev_create_gpe_block : GPE 00 to
31 [_GPE] 4 regs at 0000000000001028 on int 9
evgpeblk-0925 [06] ev_create_gpe_block : Found 6
Wake, Enabled 2 Runtime GPEs in this block
Completing Region/Field/Buffer/Package
initialization:................................................................
Initialized 20/20 Regions 0/0 Fields 34/34 Buffers
10/16 Packages (634 nodes)
Executing all Device _STA and_INI
methods:.......................................................
55 Devices found containing: 55 _STA, 2 _INI methods
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: System [ACPI] (supports S0 S1 S3 S4 S5)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
Transparent bridge - Intel Corp. 82801BAM/CAM PCI
Bridge
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table
[\_SB_.PCI0.HUB_._PRT]
[ACPI Debug] Buffer: Length 0x06ACPI: PCI Interrupt
Link [LNKA] (IRQs 10)
ACPI: PCI Interrupt Link [LNKB] (IRQs 10)
ACPI: PCI Interrupt Link [LNKC] (IRQs 10)
ACPI: PCI Interrupt Link [LNKD] (IRQs 10)
[ACPI Debug] Buffer: Length 0x06ACPI: PCI Interrupt
Link [LNKE] (IRQs 10)
[ACPI Debug] Buffer: Length 0x06ACPI: PCI Interrupt
Link [LNKF] (IRQs 10)
[ACPI Debug] Buffer: Length 0x06ACPI: PCI Interrupt
Link [LNKG] (IRQs 10)
[ACPI Debug] Buffer: Length 0x06ACPI: PCI Interrupt
Link [LNKH] (IRQs *10)
ACPI: Embedded Controller [EC0] (gpe 28)
PCI: Probing PCI hardware
[ACPI Debug] Buffer: Length 0x06[ACPI Debug] Buffer:
Length 0x06ACPI: PCI Interrupt Link [LNKA] enabled at
IRQ 11
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
[ACPI Debug] Buffer: Length 0x06[ACPI Debug] Buffer:
Length 0x06ACPI: PCI Interrupt Link [LNKH] enabled at
IRQ 10
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
[ACPI Debug] Buffer: Length 0x06[ACPI Debug] Buffer:
Length 0x06ACPI: PCI Interrupt Link [LNKE] enabled at
IRQ 11
[ACPI Debug] Buffer: Length 0x06[ACPI Debug] Buffer:
Length 0x06ACPI: PCI Interrupt Link [LNKF] enabled at
IRQ 11
[ACPI Debug] Buffer: Length 0x06[ACPI Debug] Buffer:
Length 0x06ACPI: PCI Interrupt Link [LNKG] enabled at
IRQ 11
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option
'pci=noacpi' or even 'acpi=off'
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society
NET3.039
Initializing RT netlink socket
Starting kswapd
Installing knfsd (copyright (C) 1996
okir@monad.swb.de).
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Processor [CPU0] (supports C1 C2 C3, 5
performance states, 8 throttling states)
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with
MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
8139too Fast Ethernet driver 0.9.26
eth0: RealTek RTL8139 at 0xdf80d000,
00:02:3f:14:9d:0d, IRQ 11
eth0: Identified 8139 chip type 'RTL-8101'
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory:
424M
agpgart: Detected an Intel(R) 855GM Chipset.
agpgart: Detected 16252K stolen memory.
agpgart: AGP aperture is 128M @ 0xb0000000
[drm] Initialized tdfx 1.0.0 20010216 on minor 0
[drm] AGP 0.99 Aperture @ 0xb0000000 128MB
[drm] Initialized radeon 1.7.0 20020828 on minor 1
[drm] AGP 0.99 Aperture @ 0xb0000000 128MB
[drm] Initialized i810 1.2.1 20020211 on minor 2
Uniform Multi-Platform E-IDE driver Revision:
7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes;
override with idebus=xx
ICH4: IDE controller at PCI slot 00:1f.1
PCI: Enabling device 00:1f.1 (0005 -> 0007)
ICH4: chipset revision 3
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1100-0x1107, BIOS settings:
hda:DMA, hdb:pio
ide1: BM-DMA at 0x1108-0x110f, BIOS settings:
hdc:DMA, hdd:pio
hda: TOSHIBA MK4025GAS, ATA DISK drive
blk: queue c042f120, I/O limit 4095Mb (mask
0xffffffff)
hdc: TOSHIBA DVD-ROM SD-R6112, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 78140160 sectors (40008 MB), CHS=4864/255/63,
UDMA(33)
hdc: attached ide-cdrom driver.
hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB
Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
Partition check:
hda: hda1 hda2 hda3
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k
scsi_hostadapter, errno = 2
Intel 810 + AC97 Audio, version 0.24, 11:29:17 Jul 8
2004
PCI: Setting latency timer of device 00:1f.5 to 64
i810: Intel ICH4 found at IO 0xe200 and 0xe100, MEM
0xf0080400 and 0xf0080600, IRQ 5
i810: Intel ICH4 mmio at 0xdf895400 and 0xdf897600
i810_audio: Primary codec has ID 0
i810_audio: Audio Controller supports 6 channels.
i810_audio: Defaulting to base 2 channel mode.
i810_audio: Resetting connection 0
i810_audio: Connection 0 with codec id 0
ac97_codec: AC97 Audio codec, id: ALG64 (Unknown)
i810_audio: AC'97 codec 0 supports AMAP, total
channels = 2
cmpci: version $Revision: 6.16 $ time 11:29:18 Jul 8
2004
es1371: version v0.32 time 11:30:23 Jul 8 2004
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik
<vojtech@suse.cz>
hid-core.c: USB HID support drivers
usb.c: registered new driver serial
usbserial.c: USB Serial support registered for Generic
usbserial.c: USB Serial Driver core v1.4
usbserial.c: USB Serial support registered for
Handspring Visor / Treo / Palm 4.0 / Clié 4.x
usbserial.c: USB Serial support registered for Sony
Clié 3.5
visor.c: USB HandSpring Visor, Palm m50x, Treo, Sony
Clié driver v1.7
ipaq.c: USB PocketPC PDA driver v0.5
usbserial.c: USB Serial support registered for
PocketPC PDA
usbserial.c: USB Serial support registered for Connect
Tech - WhiteHEAT - (prerenumeration)
usbserial.c: USB Serial support registered for Connect
Tech - WhiteHEAT
whiteheat.c: USB ConnectTech WhiteHEAT driver v1.2
ftdi_sio.c: ftdi_init
usbserial.c: USB Serial support registered for FTDI
SIO
usbserial.c: USB Serial support registered for FTDI
8U232AM Compatible
usbserial.c: USB Serial support registered for FTDI
FT232BM Compatible
usbserial.c: USB Serial support registered for
USB-UIRT Infrared Tranceiver
usbserial.c: USB Serial support registered for
Home-Electronics TIRA-1 IR Transceiver
ftdi_sio.c: v1.3.5:USB FTDI Serial Converters Driver
usbserial.c: USB Serial support registered for Digi
USB
usbserial.c: USB Serial support registered for Digi
USB
digi_acceleport.c: v1.80.1.2:Digi AccelePort
USB-2/USB-4 Serial Converter driver
usbserial.c: USB Serial support registered for Belkin
/ Peracom / GoHubs USB Serial Adapter
belkin_sa.c: USB Belkin Serial converter driver v1.2
usbserial.c: USB Serial support registered for Empeg
empeg.c: v1.2:USB Empeg Mark I/II Driver
usbserial.c: USB Serial support registered for Magic
Control Technology USB-RS232
mct_u232.c: Magic Control Technology USB-RS232
converter driver v1.2
usbserial.c: USB Serial support registered for
Edgeport 1 port adapter
usbserial.c: USB Serial support registered for
Edgeport 2 port adapter
usbserial.c: USB Serial support registered for
Edgeport 4 port adapter
usbserial.c: USB Serial support registered for
Edgeport 8 port adapter
io_edgeport.c: Edgeport USB Serial Driver v2.3
usbserial.c: USB Serial support registered for
Edgeport TI 1 port adapter
usbserial.c: USB Serial support registered for
Edgeport TI 2 port adapter
io_ti.c: Edgeport USB Serial Driver v0.2
usbserial.c: USB Serial support registered for PL-2303
pl2303.c: Prolific PL2303 USB to serial adaptor driver
v0.10
usbserial.c: USB Serial support registered for
KL5KUSB105D / PalmConnect
kl5kusb105.c: KLSI KL5KUSB105 chipset USB->Serial
Converter driver v0.3a
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind
32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 132k freed
Adding Swap: 634556k swap-space (priority -1)
usb-uhci.c: $Revision: 1.275 $ time 11:45:06 Jul 8
2004
usb-uhci.c: High bandwidth mode enabled
PCI: Setting latency timer of device 00:1d.0 to 64
usb-uhci.c: USB UHCI at I/O 0x1200, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.1 to 64
usb-uhci.c: USB UHCI at I/O 0x1600, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.2 to 64
usb-uhci.c: USB UHCI at I/O 0x1700, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller
Interface driver
hub.c: new USB device 00:1d.0-1, assigned address 2
hiddev0: USB HID v1.10 Mouse [KYE Wireless Webscroll+
NBEye] on usb1:2.0
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
uhci.c: USB Universal Host Controller Interface driver
v1.1
uhci.c: USB Universal Host Controller Interface driver
v1.1
Everything seems to be OK but I cannot make my mouse
work.
To check that the mouse is working I make a
cat /dev/input/mice, but it complains that there
is not such device.
If I type ls -l /dev/input/mice I get
crw-r--r-- 1 root root 13, 63 Jun 22
09:53 /dev/input/mice
Any ideas what's happening ?
Best Regards,
Aitor
__________________________________
Do you Yahoo!?
Yahoo! Mail - 50x more storage than other providers!
http://promotions.yahoo.com/new_mail
Reply to: