--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: linux-image-3.2.0-2-amd64: system unresponsive during disk copy (seems locked up)
- From: Michal Suchanek <michal.suchanek@ruk.cuni.cz>
- Date: Tue, 17 Jul 2012 15:55:24 +0200
- Message-id: <20120717135524.17040.69073.reportbug@OptiPlex960.ruk.cuni.cz>
Package: src
Version: 3.2.20-1
Severity: normal
Hello,
I observe what seems like a system lockup when copying large amount of
data.
The amount of data transferred does not seem to matter but the time it
takes to transfer does.
I was restoring a disk image to a disk in external enclosure (sdg).
This involves reading some random files (the restore scipt uses cat,
ewh), ungzipping the concatenation, and feeding that to a program that
frobs the data and restores them to appropriate blocks on the partition.
About firtst minute went fine, then the system was totally frozen for
about 4 minutes, and then about two minutes it was _very_ unresponsive
but updated the on-screen picture a few times and allowed remote login.
Last 3 minutes of copy went fine again.
Similar results with dd if=some-dvd-image.iso of=/some/flash/drive but only
with some (slow?) flash drives.
vbox is installed (and the modules loaded) but no virtual machine is running.
-- Package-specific info:
** Version:
Linux version 3.2.0-2-amd64 (Debian 3.2.18-1) (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-1) ) #1 SMP Mon May 21 17:45:41 UTC 2012
** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.2.0-2-amd64 root=UUID=3b8f6a64-5899-462a-aec0-6ddefd878ecf ro fbcon=rotate:3 quiet
** Tainted: O (4096)
* Out-of-tree module has been loaded.
** Kernel log:
[1811633.355259] scsi 8:0:0:0: Direct-Access ATA ST380817AS 3.42 PQ: 0 ANSI: 5
[1811633.355499] sd 8:0:0:0: [sdg] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[1811633.355631] sd 8:0:0:0: [sdg] Write Protect is off
[1811633.355635] sd 8:0:0:0: [sdg] Mode Sense: 00 3a 00 00
[1811633.355723] sd 8:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[1811633.373021] sdg: unknown partition table
[1811633.373290] sd 8:0:0:0: [sdg] Attached SCSI disk
[1811785.734535] sdg: sdg1
[1811785.809677] sdg: sdg1
[1811785.853088] sdg: sdg1
[1812002.468067] INFO: task kworker/1:4:10835 blocked for more than 120 seconds.
[1812002.468071] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[1812002.468074] kworker/1:4 D ffff880127c53540 0 10835 2 0x00000000
[1812002.468079] ffff880073ef87f0 0000000000000046 0000000000000000 ffff8801233480c0
[1812002.468085] 0000000000013540 ffff88010517ffd8 ffff88010517ffd8 ffff880073ef87f0
[1812002.468089] 0000000000000002 000000018103ea7d 0000000000000000 7fffffffffffffff
[1812002.468094] Call Trace:
[1812002.468103] [<ffffffff813485fe>] ? schedule_timeout+0x2c/0xdb
[1812002.468108] [<ffffffff810135ad>] ? paravirt_read_tsc+0x5/0x8
[1812002.468111] [<ffffffff81013a1f>] ? native_sched_clock+0x27/0x2f
[1812002.468114] [<ffffffff81013a2c>] ? sched_clock+0x5/0x8
[1812002.468118] [<ffffffff81063674>] ? sched_clock_local+0xd/0x6f
[1812002.468122] [<ffffffff81348244>] ? wait_for_common+0xa0/0x119
[1812002.468126] [<ffffffff8103f3ff>] ? try_to_wake_up+0x197/0x197
[1812002.468130] [<ffffffff8105f041>] ? kthread_create_on_node+0x8f/0x109
[1812002.468134] [<ffffffff8105bd07>] ? manage_workers.isra.23+0x15b/0x15b
[1812002.468137] [<ffffffff8105bb16>] ? create_worker+0xcb/0x161
[1812002.468140] [<ffffffff8105bc53>] ? manage_workers.isra.23+0xa7/0x15b
[1812002.468143] [<ffffffff8105bd94>] ? worker_thread+0x8d/0x145
[1812002.468146] [<ffffffff8105bd07>] ? manage_workers.isra.23+0x15b/0x15b
[1812002.468150] [<ffffffff8105ef05>] ? kthread+0x76/0x7e
[1812002.468154] [<ffffffff813505b4>] ? kernel_thread_helper+0x4/0x10
[1812002.468158] [<ffffffff8105ee8f>] ? kthread_worker_fn+0x139/0x139
[1812002.468161] [<ffffffff813505b0>] ? gs_change+0x13/0x13
[1812122.468087] INFO: task kworker/1:4:10835 blocked for more than 120 seconds.
[1812122.468092] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[1812122.468094] kworker/1:4 D ffff880127c53540 0 10835 2 0x00000000
[1812122.468099] ffff880073ef87f0 0000000000000046 0000000000000000 ffff8801233480c0
[1812122.468103] 0000000000013540 ffff88010517ffd8 ffff88010517ffd8 ffff880073ef87f0
[1812122.468106] 0000000000000002 000000018103ea7d 0000000000000000 7fffffffffffffff
[1812122.468110] Call Trace:
[1812122.468120] [<ffffffff813485fe>] ? schedule_timeout+0x2c/0xdb
[1812122.468125] [<ffffffff810135ad>] ? paravirt_read_tsc+0x5/0x8
[1812122.468128] [<ffffffff81013a1f>] ? native_sched_clock+0x27/0x2f
[1812122.468130] [<ffffffff81013a2c>] ? sched_clock+0x5/0x8
[1812122.468134] [<ffffffff81063674>] ? sched_clock_local+0xd/0x6f
[1812122.468137] [<ffffffff81348244>] ? wait_for_common+0xa0/0x119
[1812122.468141] [<ffffffff8103f3ff>] ? try_to_wake_up+0x197/0x197
[1812122.468145] [<ffffffff8105f041>] ? kthread_create_on_node+0x8f/0x109
[1812122.468148] [<ffffffff8105bd07>] ? manage_workers.isra.23+0x15b/0x15b
[1812122.468150] [<ffffffff8105bb16>] ? create_worker+0xcb/0x161
[1812122.468153] [<ffffffff8105bc53>] ? manage_workers.isra.23+0xa7/0x15b
[1812122.468155] [<ffffffff8105bd94>] ? worker_thread+0x8d/0x145
[1812122.468157] [<ffffffff8105bd07>] ? manage_workers.isra.23+0x15b/0x15b
[1812122.468160] [<ffffffff8105ef05>] ? kthread+0x76/0x7e
[1812122.468164] [<ffffffff813505b4>] ? kernel_thread_helper+0x4/0x10
[1812122.468167] [<ffffffff8105ee8f>] ? kthread_worker_fn+0x139/0x139
[1812122.468169] [<ffffffff813505b0>] ? gs_change+0x13/0x13
[1812122.468176] INFO: task kworker/3:3:12627 blocked for more than 120 seconds.
[1812122.468177] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[1812122.468179] kworker/3:3 D ffff880127cd3540 0 12627 2 0x00000000
[1812122.468182] ffff8800423d9750 0000000000000046 0000000000000000 ffff88012339cf60
[1812122.468186] 0000000000013540 ffff880100bd3fd8 ffff880100bd3fd8 ffff8800423d9750
[1812122.468189] 0000000000000000 000000018103ea7d 0000000000000000 7fffffffffffffff
[1812122.468193] Call Trace:
[1812122.468195] [<ffffffff813485fe>] ? schedule_timeout+0x2c/0xdb
[1812122.468198] [<ffffffff810135ad>] ? paravirt_read_tsc+0x5/0x8
[1812122.468200] [<ffffffff81013a1f>] ? native_sched_clock+0x27/0x2f
[1812122.468202] [<ffffffff81013a2c>] ? sched_clock+0x5/0x8
[1812122.468205] [<ffffffff81063674>] ? sched_clock_local+0xd/0x6f
[1812122.468207] [<ffffffff81348244>] ? wait_for_common+0xa0/0x119
[1812122.468210] [<ffffffff8103f3ff>] ? try_to_wake_up+0x197/0x197
[1812122.468213] [<ffffffff8105f041>] ? kthread_create_on_node+0x8f/0x109
[1812122.468215] [<ffffffff8105bd07>] ? manage_workers.isra.23+0x15b/0x15b
[1812122.468218] [<ffffffff8105bb16>] ? create_worker+0xcb/0x161
[1812122.468220] [<ffffffff8105bc53>] ? manage_workers.isra.23+0xa7/0x15b
[1812122.468222] [<ffffffff8105bd94>] ? worker_thread+0x8d/0x145
[1812122.468225] [<ffffffff8105bd07>] ? manage_workers.isra.23+0x15b/0x15b
[1812122.468227] [<ffffffff8105ef05>] ? kthread+0x76/0x7e
[1812122.468230] [<ffffffff813505b4>] ? kernel_thread_helper+0x4/0x10
[1812122.468233] [<ffffffff8105ee8f>] ? kthread_worker_fn+0x139/0x139
[1812122.468235] [<ffffffff813505b0>] ? gs_change+0x13/0x13
[1812643.835127] ata9: exception Emask 0x50 SAct 0x0 SErr 0x4090800 action 0xe frozen
[1812643.835132] ata9: irq_stat 0x00400040, connection status changed
[1812643.835136] ata9: SError: { HostInt PHYRdyChg 10B8B DevExch }
[1812643.835143] ata9: hard resetting link
[1812644.556028] ata9: SATA link down (SStatus 0 SControl 300)
[1812649.556020] ata9: hard resetting link
[1812649.876023] ata9: SATA link down (SStatus 0 SControl 300)
[1812649.876031] ata9: limiting SATA link speed to 1.5 Gbps
[1812654.876012] ata9: hard resetting link
[1812655.196039] ata9: SATA link down (SStatus 0 SControl 310)
[1812655.196047] ata9.00: disabled
[1812655.196061] ata9: EH complete
[1812655.196073] ata9.00: detaching (SCSI 8:0:0:0)
[1812655.197171] sd 8:0:0:0: [sdg] Synchronizing SCSI cache
[1812655.197219] sd 8:0:0:0: [sdg] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[1812655.197224] sd 8:0:0:0: [sdg] Stopping disk
[1812655.197233] sd 8:0:0:0: [sdg] START_STOP FAILED
[1812655.197236] sd 8:0:0:0: [sdg] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
** Model information
sys_vendor: Dell Inc.
product_name: OptiPlex 960
product_version:
chassis_vendor: Dell Inc.
chassis_version:
bios_vendor: Dell Inc.
bios_version: A01
board_vendor: Dell Inc.
board_name: 0Y958C
board_version: A00
** Loaded modules:
vboxpci(O)
vboxnetadp(O)
vboxnetflt(O)
vboxdrv(O)
joydev
usbhid
hid
wacom
dm_mod
uinput
binfmt_misc
pci_stub
bridge
stp
xt_tcpudp
xt_conntrack
xt_state
xt_dscp
xt_DSCP
xt_CLASSIFY
ipt_LOG
ipt_REJECT
xt_owner
nf_conntrack_tftp
nf_nat_ftp
nf_conntrack_ftp
nf_nat_sip
nf_conntrack_sip
nf_nat_h323
nf_conntrack_h323
nf_nat_pptp
nf_nat_proto_gre
nf_conntrack_pptp
nf_conntrack_proto_gre
nf_nat_irc
nf_conntrack_irc
iptable_filter
iptable_nat
ipt_MASQUERADE
nf_nat
xt_multiport
xt_iprange
nf_conntrack_ipv4
nf_defrag_ipv4
nf_conntrack
ip_tables
x_tables
tun
fuse
kvm_intel
kvm
snd_pcm_oss
snd_mixer_oss
coretemp
loop
snd_hda_codec_hdmi
snd_hda_codec_analog
dell_wmi
sparse_keymap
evdev
snd_hda_intel
snd_hda_codec
snd_hwdep
snd_pcm
snd_page_alloc
snd_seq
snd_seq_device
snd_timer
psmouse
pcspkr
dcdbas
i2c_i801
serio_raw
snd
iTCO_wdt
iTCO_vendor_support
soundcore
parport_pc
parport
wmi
button
processor
thermal_sys
ext3
mbcache
jbd
sr_mod
sd_mod
cdrom
crc_t10dif
usb_storage
uas
sata_sil24
ahci
libahci
uhci_hcd
radeon
ata_generic
power_supply
i2c_algo_bit
libata
e1000e
drm_kms_helper
ttm
drm
i2c_core
ehci_hcd
usbcore
scsi_mod
usb_common
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 4 Series Chipset DRAM Controller [8086:2e10] (rev 03)
Subsystem: Dell Device [1028:0276]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: Intel Corporation 4 Series Chipset PCI Express Root Port [8086:2e11] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fe900000-feafffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:03.0 Communication controller [0780]: Intel Corporation 4 Series Chipset HECI Controller [8086:2e14] (rev 03)
Subsystem: Dell Device [1028:0276]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f0000800 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
00:03.2 IDE interface [0101]: Intel Corporation 4 Series Chipset PT IDER Controller [8086:2e16] (rev 03) (prog-if 85 [Master SecO PriO])
Subsystem: Dell Device [1028:0276]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 0: I/O ports at fe80 [size=8]
Region 1: I/O ports at fe90 [size=4]
Region 2: I/O ports at fea0 [size=8]
Region 3: I/O ports at feb0 [size=4]
Region 4: I/O ports at fef0 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_generic
00:03.3 Serial controller [0700]: Intel Corporation 4 Series Chipset Serial KT Controller [8086:2e17] (rev 03) (prog-if 02 [16550])
Subsystem: Dell Device [1028:0276]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at ec98 [size=8]
Region 1: Memory at febd8000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: serial
00:19.0 Ethernet controller [0200]: Intel Corporation 82567LM-3 Gigabit Network Connection [8086:10de] (rev 02)
Subsystem: Dell Device [1028:0276]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 49
Region 0: Memory at febe0000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at febd9000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at ecc0 [size=32]
Capabilities: <access denied>
Kernel driver in use: e1000e
00:1a.0 USB controller [0c03]: Intel Corporation 82801JD/DO (ICH10 Family) USB UHCI Controller #4 [8086:3a67] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:0276]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at ff20 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.1 USB controller [0c03]: Intel Corporation 82801JD/DO (ICH10 Family) USB UHCI Controller #5 [8086:3a68] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:0276]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at ff00 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.2 USB controller [0c03]: Intel Corporation 82801JD/DO (ICH10 Family) USB UHCI Controller #6 [8086:3a69] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:0276]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 4: I/O ports at fc00 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.7 USB controller [0c03]: Intel Corporation 82801JD/DO (ICH10 Family) USB2 EHCI Controller #2 [8086:3a6c] (rev 02) (prog-if 20 [EHCI])
Subsystem: Dell Device [1028:0276]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 0: Memory at febda000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1b.0 Audio device [0403]: Intel Corporation 82801JD/DO (ICH10 Family) HD Audio Controller [8086:3a6e] (rev 02)
Subsystem: Dell Device [1028:0276]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 51
Region 0: Memory at febdc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801JD/DO (ICH10 Family) PCI Express Port 1 [8086:3a70] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: fe800000-fe8fffff
Prefetchable memory behind bridge: 00000000f0300000-00000000f04fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.1 PCI bridge [0604]: Intel Corporation 82801JD/DO (ICH10 Family) PCI Express Port 2 [8086:3a72] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fe700000-fe7fffff
Prefetchable memory behind bridge: 00000000f0100000-00000000f02fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 82801JD/DO (ICH10 Family) USB UHCI Controller #1 [8086:3a64] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:0276]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at ff80 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.1 USB controller [0c03]: Intel Corporation 82801JD/DO (ICH10 Family) USB UHCI Controller #2 [8086:3a65] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:0276]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at ff60 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.2 USB controller [0c03]: Intel Corporation 82801JD/DO (ICH10 Family) USB UHCI Controller #3 [8086:3a66] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:0276]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at ff40 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.7 USB controller [0c03]: Intel Corporation 82801JD/DO (ICH10 Family) USB2 EHCI Controller #1 [8086:3a6a] (rev 02) (prog-if 20 [EHCI])
Subsystem: Dell Device [1028:0276]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at ff980000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev a2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801JDO (ICH10DO) LPC Interface Controller [8086:3a14] (rev 02)
Subsystem: Dell Device [1028:0276]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 SATA controller [0106]: Intel Corporation 82801JD/DO (ICH10 Family) SATA AHCI Controller [8086:3a02] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Dell Device [1028:0276]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 50
Region 0: I/O ports at fe00 [size=8]
Region 1: I/O ports at fe10 [size=4]
Region 2: I/O ports at fe20 [size=8]
Region 3: I/O ports at fe30 [size=4]
Region 4: I/O ports at fec0 [size=32]
Region 5: Memory at f0000000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 82801JD/DO (ICH10 Family) SMBus Controller [8086:3a60] (rev 02)
Subsystem: Dell Device [1028:0276]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at febdb000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at ece0 [size=32]
Kernel driver in use: i801_smbus
01:00.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI Cedar PRO [Radeon HD 5450] [1002:68f9] (prog-if 00 [VGA controller])
Subsystem: PC Partner Limited Device [174b:e164]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 48
Region 0: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 2: Memory at fe9e0000 (64-bit, non-prefetchable) [size=128K]
Region 4: I/O ports at dc00 [size=256]
Expansion ROM at fea00000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: radeon
01:00.1 Audio device [0403]: Advanced Micro Devices [AMD] nee ATI Cedar HDMI Audio [Radeon HD 5400/6300 Series] [1002:aa68]
Subsystem: PC Partner Limited Device [174b:aa68]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 52
Region 0: Memory at fe9dc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
03:00.0 Mass storage controller [0180]: Silicon Image, Inc. SiI 3531 [SATALink/SATARaid] Serial ATA Controller [1095:3531] (rev 01)
Subsystem: Silicon Image, Inc. SiI 3531 [SATALink/SATARaid] Serial ATA Controller [1095:3531]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fe7fd000 (64-bit, non-prefetchable) [size=128]
Region 2: Memory at fe7fe000 (64-bit, non-prefetchable) [size=8K]
Region 4: I/O ports at cc80 [size=128]
Capabilities: <access denied>
Kernel driver in use: sata_sil24
** USB devices:
Bus 008 Device 011: ID 046d:c063 Logitech, Inc. DELL Laser Mouse
Bus 008 Device 010: ID 04b3:301b IBM Corp. SK-8815 Keyboard
Bus 008 Device 009: ID 04b3:301a IBM Corp.
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 0644:0200 TEAC Corp. All-In-One Multi-Card Reader CA200/B/S
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: wheezy/sid
APT prefers stable
APT policy: (900, 'stable'), (500, 'testing'), (410, 'unstable'), (200, 'experimental'), (111, 'oldstable')
Architecture: amd64 (x86_64)
Foreign Architectures: i386
Kernel: Linux 3.2.0-2-amd64 (SMP w/4 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8) (ignored: LC_ALL set to en_US.UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-3.2.0-2-amd64 depends on:
ii debconf [debconf-2.0] 1.5.44
ii initramfs-tools [linux-initramfs-tool] 0.106
ii kmod 8-2
ii linux-base 3.5
ii module-init-tools 8-2
Versions of packages linux-image-3.2.0-2-amd64 recommends:
ii firmware-linux-free 3.1
Versions of packages linux-image-3.2.0-2-amd64 suggests:
ii grub-pc 1.98+20100804-14+squeeze1
pn linux-doc-3.2 <none>
Versions of packages linux-image-3.2.0-2-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
ii firmware-linux-nonfree 0.36
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.2.0-2-amd64/postinst/ignoring-ramdisk:
linux-image-3.2.0-2-amd64/postinst/depmod-error-initrd-3.2.0-2-amd64: false
linux-image-3.2.0-2-amd64/postinst/missing-firmware-3.2.0-2-amd64:
linux-image-3.2.0-2-amd64/prerm/removing-running-kernel-3.2.0-2-amd64: true
--- End Message ---