Sandro Tosi ha scritto:
riconosce e lo monta automaticamente, per entrambe le partizioni.
Mentre
per la memory bar, per il mouse, per il lettore mp3... Ceste! Nemmeno
montando manualmente:
mount /dev/sda1 /mnt/hdr
ma che errore ti da'?? Puoi provare a vedere nei log di sistema che
scrive quando inserisci quei dispositivi che poi non riesci a montare:
apri una console e, da root, fai
# tail -f /var/log/messages
ul 6 00:26:56 localhost xfs-xtt: Warning: font renderer for ".TTF"
already registered at priority 10
Jul 6 00:26:56 localhost xfs-xtt: Warning: font renderer for ".TTC"
already registered at priority 10
Jul 6 00:26:56 localhost xfs-xtt: ignoring font path element
/var/lib/defoma/x-ttcidfont-conf.d/dirs/CID (unreadable)
Jul 6 00:26:56 localhost xfs-xtt: ignoring font path element
/usr/lib/X11/fonts/cyrillic/:unscaled (unreadable)
Jul 6 00:26:56 localhost xfs-xtt: ignoring font path element
/usr/lib/X11/fonts/Speedo/ (unreadable)
Jul 6 00:27:00 localhost Xprt_64: No matching visual for
__GLcontextMode with visual class = 0 (32775), nplanes = 8
Jul 6 00:29:22 localhost gconfd (mircoh-7682): Inizializzazione
(versione 2.10.0), pid 7682, utente 'mircoh'
Jul 6 00:29:22 localhost gconfd (mircoh-7682): L'indirizzo
"xml:readonly:/etc/gconf/gconf.xml.mandatory"�stato risolta ad una
fonte di configurazione in sola lettura in posizione 0
Jul 6 00:29:22 localhost gconfd (mircoh-7682): L'indirizzo
"xml:readwrite:/home/mircoh/.gconf" �stato risolto ad una fonte di
configurazione scrivibile in posizione 1
Jul 6 00:29:22 localhost gconfd (mircoh-7682): L'indirizzo
"xml:readonly:/etc/gconf/gconf.xml.defaults" �stato risolta ad una
fonte di configurazione in sola lettura in posizione 2
Jul 6 00:33:36 localhost exiting on signal 15
Jul 6 00:33:37 localhost syslogd 1.4.1#16ubuntu6
poi inserisci la chiavina usb (tipo...) e vedi che scrive. Oppure,
dopo aver inserito la chiavina digita
# dmesg
Processor #0 15:12 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: root=/dev/hda2 ro quiet splash
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 797.967 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 251548k/261568k available (1436k kernel code, 9400k reserved, 754k data, 224k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 1576.96 BogoMIPS (lpj=788480)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 078bfbff c3d3fbff 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 078bfbff c3d3fbff 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 078bfbff c3d3fbff 00000000 00000010 00000000 00000000
CPU: AMD Mobile AMD Sempron(tm) Processor 2800+ stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
ACPI: Looking for DSDT in initrd... not found!
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=0 pin2=-1
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
Freeing initrd memory: 4300k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfd8bc, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller [EC0] (gpe 33)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP0._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 16 18 19) *0
ACPI: PCI Interrupt Link [LNK2] (IRQs 16 18 19) *0
ACPI: PCI Interrupt Link [LNK3] (IRQs 17) *0
ACPI: PCI Interrupt Link [LNK4] (IRQs 16 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNK5] (IRQs 16 18 19) *0
ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [LUS1] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [LMCI] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [LPID] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 22) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas@hp.com
** so I can fix the driver.
pnp: 00:00: ioport range 0x8000-0x807f could not be reserved
pnp: 00:00: ioport range 0x8080-0x80ff has been reserved
pnp: 00:00: ioport range 0x8400-0x847f has been reserved
pnp: 00:00: ioport range 0x8480-0x84ff could not be reserved
pnp: 00:00: ioport range 0x8800-0x887f has been reserved
pnp: 00:00: ioport range 0x8880-0x88ff has been reserved
pnp: 00:00: ioport range 0x2040-0x207f has been reserved
pnp: 00:00: ioport range 0x2000-0x203f has been reserved
Simple Boot Flag at 0x37 set to 0x1
audit: initializing netlink socket (disabled)
audit(1120609561.501:0): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
ACPI: PCI Interrupt Link [LMCI] enabled at IRQ 22
ACPI: PCI interrupt 0000:00:06.1[B] -> GSI 22 (level, low) -> IRQ 22
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
input: AT Translated Set 2 keyboard on isa0060/serio0
EISA: Probing bus 0 at eisa0
Cannot allocate resource for EISA slot 1
Cannot allocate resource for EISA slot 2
Cannot allocate resource for EISA slot 3
Cannot allocate resource for EISA slot 4
Cannot allocate resource for EISA slot 5
Cannot allocate resource for EISA slot 6
Cannot allocate resource for EISA slot 7
Cannot allocate resource for EISA slot 8
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
NET: Registered protocol family 8
NET: Registered protocol family 20
Restarting tasks...<6> Strange, kswapd0 not stopped
Strange, kseriod not stopped
done
ACPI wakeup devices:
USB0 USB1 USB2 PS2K PS2M MAC0
ACPI: (supports S0 S3 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4300KiB [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 224k freed
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Thermal Zone [THRM] (54 C)
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE3-150: IDE controller at PCI slot 0000:00:08.0
NFORCE3-150: chipset revision 165
NFORCE3-150: not 100% native mode: will probe irqs later
NFORCE3-150: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE3-150: 0000:00:08.0 (rev a5) UDMA133 controller
ide0: BM-DMA at 0x2080-0x2087, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x2088-0x208f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: ST94019A, ATA DISK drive
elevator: using anticipatory as default io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 1024KiB
hda: 78140160 sectors (40007 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4
Probing IDE interface ide1...
hdc: DW-224E-B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
Stopping tasks: ==|
Freeing memory... done (454 pages freed)
Restarting tasks... done
VFS: Can't find ext3 filesystem on dev hda2.
VFS: Can't find an ext2 filesystem on dev hda2.
ReiserFS: hda2: found reiserfs format "3.6" with standard journal
ReiserFS: hda2: using ordered data mode
ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda2: checking transaction log (hda2)
ReiserFS: hda2: Using r5 hash to sort names
Adding 602428k swap on /dev/hda4. Priority:-1 extents:1
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 1654kB Cache
Uniform CD-ROM driver Revision: 3.20
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
lp0: using parport0 (interrupt-driven).
mice: PS/2 mouse device common for all mice
input: PS/2 Generic Mouse on isa0060/serio4
ieee1394: Initialized config rom entry `ip1394'
SCSI subsystem initialized
sbp2: $Rev: 1219 $ Ben Collins <bcollins@debian.org>
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ts: Compaq touchscreen protocol output
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
USB Universal Host Controller Interface driver v2.2
usbcore: registered new driver usbmouse
drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
cpcihp_generic: Generic port I/O CompactPCI Hot Plug Driver version: 0.1
cpcihp_generic: not configured, disabling.
Capability LSM initialized
device-mapper: 4.3.0-ioctl (2004-09-30) initialised: dm-devel@redhat.com
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
cdrom: open failed.
ReiserFS: hda3: found reiserfs format "3.6" with standard journal
ReiserFS: hda3: using ordered data mode
ReiserFS: hda3: journal params: device hda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda3: checking transaction log (hda3)
ReiserFS: hda3: Using r5 hash to sort names
NTFS driver 2.1.22 [Flags: R/O MODULE].
NTFS volume version 3.1.
input: PC Speaker
Real Time Clock Driver v1.12
inserting floppy driver for 2.6.10-5-386
floppy0: no floppy controllers found
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected AGP bridge 0
agpgart: Setting up Nforce3 AGP.
agpgart: Maximum main memory to use for agp memory: 203M
agpgart: AGP aperture is 128M @ 0xf0000000
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x2040
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x2000
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 21
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 21 (level, low) -> IRQ 21
ohci_hcd 0000:00:02.0: nVidia Corporation nForce3 USB 1.1
ohci_hcd 0000:00:02.0: USB HC TakeOver failed!
ohci_hcd 0000:00:02.0: can't reset
ohci_hcd 0000:00:02.0: init 0000:00:02.0 fail, -16
ohci_hcd: probe of 0000:00:02.0 failed with error -16
ACPI: PCI Interrupt Link [LUS1] enabled at IRQ 20
ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 20 (level, low) -> IRQ 20
ohci_hcd 0000:00:02.1: nVidia Corporation nForce3 USB 1.1 (#2)
ohci_hcd 0000:00:02.1: USB HC TakeOver failed!
ohci_hcd 0000:00:02.1: can't reset
ohci_hcd 0000:00:02.1: init 0000:00:02.1 fail, -16
ohci_hcd: probe of 0000:00:02.1 failed with error -16
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 22
ACPI: PCI interrupt 0000:00:02.2[C] -> GSI 22 (level, low) -> IRQ 22
ehci_hcd 0000:00:02.2: nVidia Corporation nForce3 USB 2.0
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: irq 22, pci mem 0xe8004000
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: USB 2.0 initialized, EHCI 1.00, driver 26 Oct 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ACPI: PCI Interrupt Link [LACI] enabled at IRQ 21
ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 21 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:06.0 to 64
intel8x0_measure_ac97_clock: measured 49383 usecs
intel8x0: clocking to 47408
Evaluate _OSC Set fails. Status = 0x0005
pciehp: add_host_bridge: status 5
pciehp: Fails to gain control of native hot-plug
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Evaluate _OSC Set fails. Status = 0x0005
pciehp: add_host_bridge: status 5
pciehp: Fails to gain control of native hot-plug
ohci1394: $Rev: 1223 $ Ben Collins <bcollins@debian.org>
ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 19
ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 19 (level, low) -> IRQ 19
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[e8108000-e81087ff] Max Packet=[2048]
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
8139cp: pci dev 0000:02:01.0 (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
8139cp: Try the "8139too" driver instead.
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 18
ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 18 (level, low) -> IRQ 18
eth0: RealTek RTL8139 at 0x7000, 00:0f:b0:44:a7:bd, IRQ 18
eth0: Identified 8139 chip type 'RTL-8101'
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
ACPI: PCI interrupt 0000:02:04.0[A] -> GSI 19 (level, low) -> IRQ 19
Yenta: CardBus bridge found at 0000:02:04.0 [103c:006d]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.0, mfunc 0x01111d22, devctl 0x64
Yenta: ISA IRQ mask 0x0c70, PCI irq 19
Socket status: 30000006
ACPI: PCI interrupt 0000:02:04.1[B] -> GSI 18 (level, low) -> IRQ 18
Yenta: CardBus bridge found at 0000:02:04.1 [103c:006d]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.1, mfunc 0x01111d22, devctl 0x64
Yenta: ISA IRQ mask 0x0c70, PCI irq 18
Socket status: 30000006
ieee1394: Host added: ID:BUS[0-00:1023] GUID[4c3f02004c3f0200]
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02f0500(lo)
IPv6 over IPv4 tunneling driver
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ibm_acpi: ec object not found
ACPI: Battery Slot [BAT1] (battery absent)
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
apm: BIOS not found.
cs: IO port probe 0x0100-0x04ff: excluding 0x200-0x20f 0x4d0-0x4d7
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.00.09e)
powernow-k8: 0 : fid 0x8 (1600 MHz), vid 0x6 (1400 mV)
powernow-k8: 1 : fid 0x0 (800 MHz), vid 0x18 (950 mV)
cpu_init done, current fid 0x0, vid 0x18
eth0: no IPv6 routers present