Bug#391395: installation report

[Frans Pop <elendil@planet.nl>]

----------  Forwarded Message  ----------
Subject: Re: Bug#391395: installation report
Date: Monday 09 October 2006 18:34
From: Alexis Lee1 <alexislee@uk.ibm.com>
To: Frans Pop <elendil@planet.nl>

Hi Frans,

`lspci -n`: 00:1f.1 0101: 8086:24cb (rev 01)

`dmesg`:
... cut ...
hda: IC35L040AVVN07-0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: LTN486S, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 185
... cut ...
hda: max request size: 128KiB
hda 78156288 sectors (40016MB) w/1863KiB Cache, CHS=65535/16/63,
 UDMA(100) hda: cache flushes supported
 hda: hda1 hda2 < hda5 hda6 hda7 >
hdc: ATAPI 48X CD-ROM drive, 120kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 193
... cut ...
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Intel ISA PCIC probe: not found.
hdc: media error (bad sector): status=0x51 { DriveReady SeekComplete
 Error }
hdc: media error (bad sector): error=0x30 { LastFailedSense=0x03 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 64
isofs_fill_super: bread failed, dev=hdc, iso_blknum=16, block=16
hdc: media error (bad sector): status=0x51 { DriveReady SeekComplete
 Error }
hdc: media error (bad sector): error=0x30 { LastFailedSense=0x03 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 64
isofs_fill_super: bread failed, dev=hdc, iso_blknum=16, block=16
-- end of text --

`ls -l /dev/hdc`: /dev/hdc -> ide/host0/bus1/target0/lun0/cd
`ls -l /dev/cdroms/cdrom0`: /dev/cdroms/cdrom0 ->
ide/host0/bus1/target0/lun0/cd      (the same)
`ls -l /dev/ide/host0/bus1/target0/lun0/cd`: block device, node numbers
22,0

`df`:
tmpfs 514068 436 513632 0% /dev
tmpfs 514068 436 513632 0% /dev
tmpfs 514068 436 513632 0% /.dev

`mkdir boo; mount /dev/hdc boo`:
mount: /dev/hdc is write-protected, mounting read-only
mount: /dev/hdc is write-protected, mounting read-only
(taking a long time)
mount: /dev/hdc is write-protected, mounting read-only
mount: Mounting /dev/hdc on boo failed: Invalid argument

I get much the same if I specify "-t iso9660", but faster.


Thanks in advance,
Alexis
-------------------------------------------------------