[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Bug#683167: marked as done (linux-image-3.4-trunk-amd64: Attempting to start X with intel driver hangs system)

Your message dated Sun, 13 Jul 2014 15:10:47 +0200
with message-id <20140713131047.GA1400@betterave.cristau.org>
and subject line Re: Bug#683167: linux-image-3.4-trunk-amd64: Attempting to start X with intel driver hangs system
has caused the Debian Bug report #683167,
regarding linux-image-3.4-trunk-amd64: Attempting to start X with intel driver hangs system
to be marked as done.

This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.

(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact owner@bugs.debian.org
immediately.)


-- 
683167: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=683167
Debian Bug Tracking System
Contact owner@bugs.debian.org with problems
--- Begin Message --- 
Package: src
Version: 3.4.4-1~experimental.1
Severity: important

This is on an Ivy Bridge Xeon E3 with GPU. I thought it was the X
driver, because i915 KMS works fine for the console, it only crashes
when trying to bring up X. But I pulled in the 2.20.2 driver today and
it still happens. So I now think the problem is in the kernel.

It's entirely possible this is fixed in 3.5, which I will test as soon
as it hits experimental.

3.2 crashes as well, but not as hard as 3.4. With 3.2, X doesn't come
up, but you can switch to a console and reboot. 3.4 needs the reset
button.

-- Package-specific info:
** Version:
Linux version 3.4-trunk-amd64 (Debian 3.4.4-1~experimental.1) (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-1) ) #1 SMP Tue Jun 26 17:23:03 UTC 2012

** Command line:
BOOT_IMAGE=/vmlinuz-3.4-trunk-amd64 root=/dev/mapper/luks-root ro quiet

** Not tainted

** Kernel log:
[   43.319002] Monitor-Mwait will be used to enter C-3 state
[   43.319016] ACPI: acpi_idle registered with cpuidle
[   43.323450] iTCO_vendor_support: vendor-support=0
[   43.324345] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
[   43.324409] iTCO_wdt: Found a Panther Point TCO device (Version=2, TCOBASE=0x0460)
[   43.324449] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   43.329003] ACPI Warning: 0x000000000000f040-0x000000000000f05f SystemIO conflicts with Region \_SB_.PCI0.SBUS.SMBI 1 (20120320/utaddress-251)
[   43.329008] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   43.344385] wmi: Mapper loaded
[   43.344513] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input6
[   43.344826] ACPI: Power Button [PWRF]
[   43.345309] Bluetooth: Core ver 2.16
[   43.345318] NET: Registered protocol family 31
[   43.345319] Bluetooth: HCI device and connection manager initialized
[   43.345321] Bluetooth: HCI socket layer initialized
[   43.345322] Bluetooth: L2CAP socket layer initialized
[   43.345325] Bluetooth: SCO socket layer initialized
[   43.347792] input: PC Speaker as /devices/platform/pcspkr/input/input7
[   43.348878] Linux media interface: v0.10
[   43.349854] usbcore: registered new interface driver btusb
[   43.349925] microcode: CPU0 sig=0x306a9, pf=0x2, revision=0x10
[   43.351137] Linux video capture interface: v2.00
[   43.352848] snd_hda_intel 0000:00:1b.0: enabling device (0000 -> 0002)
[   43.352902] snd_hda_intel 0000:00:1b.0: irq 55 for MSI/MSI-X
[   43.354422] uvcvideo: Found UVC 1.00 device <unnamed> (046d:081d)
[   43.366279] usb 4-1.6.1: input irq status -75 received
[   43.367115] input: UVC Camera (046d:081d) as /devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.7/4-1.7:1.2/input/input8
[   43.367167] usbcore: registered new interface driver uvcvideo
[   43.367168] USB Video Class driver (1.1.1)
[   43.371842] asus_wmi: ASUS WMI generic driver loaded
[   43.372554] asus_wmi: Initialization: 0x0
[   43.372568] asus_wmi: BIOS WMI version: 0.9
[   43.372592] asus_wmi: SFUN value: 0x0
[   43.372755] input: Eee PC WMI hotkeys as /devices/platform/eeepc-wmi/input/input9
[   43.373301] asus_wmi: Backlight controlled by ACPI video driver
[   43.373916] microcode: CPU1 sig=0x306a9, pf=0x2, revision=0x10
[   43.375110] microcode: CPU2 sig=0x306a9, pf=0x2, revision=0x10
[   43.376077] microcode: CPU3 sig=0x306a9, pf=0x2, revision=0x10
[   43.377564] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[   43.381261] usbcore: registered new interface driver snd-usb-audio
[   43.390225] usb 4-1.6.1: input irq status -75 received
[   43.402028] input: HDA Intel PCH Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[   43.402110] input: HDA Intel PCH Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[   43.402165] input: HDA Intel PCH Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[   43.402201] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13
[   43.402235] input: HDA Intel PCH Line Out Side as /devices/pci0000:00/0000:00:1b.0/sound/card0/input14
[   43.402276] input: HDA Intel PCH Line Out CLFE as /devices/pci0000:00/0000:00:1b.0/sound/card0/input15
[   43.402344] input: HDA Intel PCH Line Out Surround as /devices/pci0000:00/0000:00:1b.0/sound/card0/input16
[   43.402436] input: HDA Intel PCH Line Out Front as /devices/pci0000:00/0000:00:1b.0/sound/card0/input17
[   46.841151] XFS (sde2): Mounting Filesystem
[   47.759356] XFS (sde2): Ending clean mount
[   47.828292] FAT-fs (sde1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[   47.846638] XFS (dm-8): Mounting Filesystem
[   48.029741] XFS (dm-8): Ending clean mount
[   48.053466] XFS (dm-9): Mounting Filesystem
[   48.167516] XFS (dm-9): Ending clean mount
[   48.178220] XFS (dm-7): Mounting Filesystem
[   48.521452] XFS (dm-7): Ending clean mount
[   49.793502] Bridge firewalling registered
[   49.795766] device eth0 entered promiscuous mode
[   49.801328] NET: Registered protocol family 3
[   49.804026] NET: Registered protocol family 6
[   49.809814] NET: Registered protocol family 11
[   49.816674] NET: Registered protocol family 4
[   49.829591] NET: Registered protocol family 5
[   49.915880] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   49.923119] ADDRCONF(NETDEV_UP): br0: link is not ready
[   51.736538] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx
[   51.736544] e1000e 0000:04:00.0: eth0: 10/100 speed: disabling TSO
[   51.738750] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   51.738779] br0: port 1(eth0) entered forwarding state
[   51.738785] br0: port 1(eth0) entered forwarding state
[   51.740350] ADDRCONF(NETDEV_CHANGE): br0: link becomes ready
[   53.245057] set resolution quirk: cval->res = 384
[   54.646255] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input18
[   54.766494] Bluetooth: RFCOMM TTY layer initialized
[   54.766497] Bluetooth: RFCOMM socket layer initialized
[   54.766498] Bluetooth: RFCOMM ver 1.11
[   54.766692] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   54.766693] Bluetooth: BNEP filters: protocol multicast
[   54.863129] lp: driver loaded but no devices found
[   54.866493] ppdev: user-space parallel port driver
[   55.011287] microcode: CPU0 updated to revision 0x12, date = 2012-04-12
[   55.011639] microcode: CPU1 updated to revision 0x12, date = 2012-04-12
[   55.011975] microcode: CPU2 updated to revision 0x12, date = 2012-04-12
[   55.012318] microcode: CPU3 updated to revision 0x12, date = 2012-04-12
[   66.732241] br0: port 1(eth0) entered forwarding state
[  140.525755] XFS (dm-10): Mounting Filesystem
[  140.639162] XFS (dm-10): Ending clean mount
[  142.924350] tun: Universal TUN/TAP device driver, 1.6
[  142.924354] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[  142.933900] device tap0 entered promiscuous mode
[  142.933941] br0: port 2(tap0) entered forwarding state
[  142.933948] br0: port 2(tap0) entered forwarding state
[  142.934751] kvm: sending ioctl 5326 to a partition!
[  142.934764] kvm: sending ioctl 80200204 to a partition!
[  142.935317] kvm: sending ioctl 5326 to a partition!
[  142.935326] kvm: sending ioctl 80200204 to a partition!
[  153.843381] tap0: no IPv6 routers present
[  157.929333] br0: port 2(tap0) entered forwarding state

** Model information
sys_vendor: System manufacturer
product_name: System Product Name
product_version: System Version
chassis_vendor: Chassis Manufacture
chassis_version: Chassis Version
bios_vendor: American Megatrends Inc.
bios_version: 0505
board_vendor: ASUSTeK COMPUTER INC.
board_name: P8C WS
board_version: Rev 1.xx

** Loaded modules:
tun
cpufreq_stats
cpufreq_userspace
cpufreq_powersave
cpufreq_conservative
parport_pc
ppdev
lp
parport
bnep
rfcomm
uinput
appletalk
ipx
p8023
rose
netrom
ax25
bridge
stp
kvm_intel
kvm
nls_utf8
nls_cp437
vfat
fat
snd_hda_codec_realtek
eeepc_wmi
asus_wmi
sparse_keymap
snd_usb_audio
coretemp
snd_usbmidi_lib
snd_seq_midi
snd_seq_midi_event
uvcvideo
videobuf2_vmalloc
snd_hda_intel
videobuf2_memops
snd_rawmidi
videobuf2_core
snd_hda_codec
videodev
microcode
snd_hwdep
snd_seq
media
btusb
snd_pcm
snd_seq_device
pcspkr
snd_page_alloc
psmouse
snd_timer
acpi_cpufreq
serio_raw
bluetooth
mperf
rfkill
joydev
crc16
evdev
snd
i2c_i801
i2c_core
soundcore
iTCO_wdt
iTCO_vendor_support
button
video
wmi
processor
xfs
sha256_generic
usb_storage
uas
dm_crypt
efivars
dm_mirror
dm_region_hash
dm_log
hid_cherry
usbhid
hid
dm_mod
sd_mod
crc_t10dif
crc32c_intel
ghash_clmulni_intel
ehci_hcd
aesni_intel
aes_x86_64
ahci
libahci
e1000e
thermal
xhci_hcd
aes_generic
cryptd
libata
scsi_mod
fan
thermal_sys
usbcore
usb_common

** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Xeon E3-1200 v2/Ivy Bridge DRAM Controller [8086:0158] (rev 09)
	Subsystem: ASUSTeK Computer Inc. Device [1043:844d]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: <access denied>
	Kernel driver in use: agpgart-intel

00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor PCI Express Root Port [8086:0151] (rev 09) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

00:02.0 VGA compatible controller [0300]: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor Graphics Controller [8086:016a] (rev 09) (prog-if 00 [VGA controller])
	Subsystem: ASUSTeK Computer Inc. Device [1043:844d]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at f7800000 (64-bit, non-prefetchable) [size=4M]
	Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
	Region 4: I/O ports at f000 [size=64]
	Expansion ROM at <unassigned> [disabled]
	Capabilities: <access denied>

00:06.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor PCI Express Root Port [8086:015d] (rev 09) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

00:14.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller [8086:1e31] (rev 04) (prog-if 30 [XHCI])
	Subsystem: ASUSTeK Computer Inc. Device [1043:844d]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 47
	Region 0: Memory at f7e00000 (64-bit, non-prefetchable) [size=64K]
	Capabilities: <access denied>
	Kernel driver in use: xhci_hcd

00:16.0 Communication controller [0780]: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 [8086:1e3a] (rev 04)
	Subsystem: ASUSTeK Computer Inc. Device [1043:844d]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at f7e1b000 (64-bit, non-prefetchable) [size=16]
	Capabilities: <access denied>

00:1a.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) (prog-if 20 [EHCI])
	Subsystem: ASUSTeK Computer Inc. Device [1043:844d]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at f7e18000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: <access denied>
	Kernel driver in use: ehci_hcd

00:1b.0 Audio device [0403]: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller [8086:1e20] (rev 04)
	Subsystem: ASUSTeK Computer Inc. Device [1043:84fb]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 55
	Region 0: Memory at f7e10000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: snd_hda_intel

00:1c.0 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 [8086:1e10] (rev c4) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

00:1c.5 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 6 [8086:1e1a] (rev c4) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
	I/O behind bridge: 0000e000-0000efff
	Memory behind bridge: f7d00000-f7dfffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

00:1c.6 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 7 [8086:1e1c] (rev c4) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
	I/O behind bridge: 0000d000-0000dfff
	Memory behind bridge: f7c00000-f7cfffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

00:1d.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 [8086:1e26] (rev 04) (prog-if 20 [EHCI])
	Subsystem: ASUSTeK Computer Inc. Device [1043:844d]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 23
	Region 0: Memory at f7e17000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: <access denied>
	Kernel driver in use: ehci_hcd

00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev a4) (prog-if 01 [Subtractive decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Bus: primary=00, secondary=06, subordinate=06, sec-latency=32
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>

00:1f.0 ISA bridge [0601]: Intel Corporation C216 Series Chipset LPC Controller [8086:1e53] (rev 04)
	Subsystem: ASUSTeK Computer Inc. Device [1043:844d]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: <access denied>

00:1f.2 RAID bus controller [0104]: Intel Corporation 82801 SATA Controller [RAID mode] [8086:2822] (rev 04)
	Subsystem: ASUSTeK Computer Inc. Device [1043:844d]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 51
	Region 0: I/O ports at f0b0 [size=8]
	Region 1: I/O ports at f0a0 [size=4]
	Region 2: I/O ports at f090 [size=8]
	Region 3: I/O ports at f080 [size=4]
	Region 4: I/O ports at f060 [size=32]
	Region 5: Memory at f7e16000 (32-bit, non-prefetchable) [size=2K]
	Capabilities: <access denied>
	Kernel driver in use: ahci

00:1f.3 SMBus [0c05]: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller [8086:1e22] (rev 04)
	Subsystem: ASUSTeK Computer Inc. Device [1043:844d]
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin C routed to IRQ 18
	Region 0: Memory at f7e15000 (64-bit, non-prefetchable) [size=256]
	Region 4: I/O ports at f040 [size=32]

04:00.0 Ethernet controller [0200]: Intel Corporation 82574L Gigabit Network Connection [8086:10d3]
	Subsystem: ASUSTeK Computer Inc. Device [1043:8369]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 17
	Region 0: Memory at f7d00000 (32-bit, non-prefetchable) [size=128K]
	Region 2: I/O ports at e000 [size=32]
	Region 3: Memory at f7d20000 (32-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: e1000e

05:00.0 Ethernet controller [0200]: Intel Corporation 82574L Gigabit Network Connection [8086:10d3]
	Subsystem: ASUSTeK Computer Inc. Device [1043:8369]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 18
	Region 0: Memory at f7c00000 (32-bit, non-prefetchable) [size=128K]
	Region 2: I/O ports at d000 [size=32]
	Region 3: Memory at f7c20000 (32-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: e1000e


** USB devices:
Bus 003 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 004 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 003: ID 046a:0023 Cherry GmbH CyMotion Master Linux Keyboard
Bus 003 Device 004: ID 1a40:0201 Terminus Technology Inc. FE 2.1 7-port Hub
Bus 003 Device 005: ID 090c:1000 Silicon Motion, Inc. - Taiwan (formerly Feiya Technology Corp.) 64MB QDI U2 DISK
Bus 003 Device 006: ID 2433:b111  
Bus 004 Device 003: ID 051d:0002 American Power Conversion Uninterruptible Power Supply
Bus 004 Device 004: ID 0a5c:4500 Broadcom Corp. BCM2046B1 USB 2.0 Hub (part of BCM2046 Bluetooth)
Bus 004 Device 005: ID 046d:081d Logitech, Inc. HD Webcam C510
Bus 004 Device 006: ID 046d:c03d Logitech, Inc. M-BT96a Pilot Optical Mouse
Bus 003 Device 007: ID 1a40:0101 Terminus Technology Inc. 4-Port HUB
Bus 004 Device 007: ID 0a5c:4502 Broadcom Corp. Keyboard (Boot Interface Subclass)
Bus 004 Device 008: ID 0a5c:4503 Broadcom Corp. Mouse (Boot Interface Subclass)
Bus 004 Device 009: ID 050d:0017 Belkin Components B8T017 Bluetooth+EDR 2.1


-- System Information:
Debian Release: wheezy/sid
  APT prefers testing
  APT policy: (500, 'testing'), (400, 'unstable'), (300, 'experimental')
Architecture: amd64 (x86_64)

Kernel: Linux 3.4-trunk-amd64 (SMP w/4 CPU cores)
Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash

Versions of packages linux-image-3.4-trunk-amd64 depends on:
ii  debconf [debconf-2.0]                   1.5.44
ii  initramfs-tools [linux-initramfs-tool]  0.107
ii  kmod                                    8-2
ii  linux-base                              3.5
ii  module-init-tools                       8-2

Versions of packages linux-image-3.4-trunk-amd64 recommends:
ii  firmware-linux-free  3.1

Versions of packages linux-image-3.4-trunk-amd64 suggests:
pn  debian-kernel-handbook     <none>
pn  grub-pc | extlinux | lilo  <none>
ii  linux-doc-3.4              3.4.4-1~experimental.1

Versions of packages linux-image-3.4-trunk-amd64 is related to:
pn  firmware-atheros        <none>
pn  firmware-bnx2           <none>
pn  firmware-bnx2x          <none>
pn  firmware-brcm80211      <none>
pn  firmware-intelwimax     <none>
pn  firmware-ipw2x00        <none>
pn  firmware-ivtv           <none>
pn  firmware-iwlwifi        <none>
pn  firmware-libertas       <none>
ii  firmware-linux          0.36
ii  firmware-linux-nonfree  0.36
pn  firmware-myricom        <none>
pn  firmware-netxen         <none>
pn  firmware-qlogic         <none>
pn  firmware-ralink         <none>
pn  firmware-realtek        <none>
pn  xen-hypervisor          <none>

-- debconf information excluded

--- End Message ---
--- Begin Message --- 
Version: 2.4.40-1

On Sun, Jul 29, 2012 at 13:36:05 +0200, Maik Zumstrull wrote:

> Package: src
> Version: 3.4.4-1~experimental.1
> Severity: important
> 
> This is on an Ivy Bridge Xeon E3 with GPU. I thought it was the X
> driver, because i915 KMS works fine for the console, it only crashes
> when trying to bring up X. But I pulled in the 2.20.2 driver today and
> it still happens. So I now think the problem is in the kernel.
> 
> It's entirely possible this is fixed in 3.5, which I will test as soon
> as it hits experimental.
> 
> 3.2 crashes as well, but not as hard as 3.4. With 3.2, X doesn't come
> up, but you can switch to a console and reboot. 3.4 needs the reset
> button.
> 
Per https://bugs.freedesktop.org/show_bug.cgi?id=53222, marking as fixed
in libdrm 2.4.34.

Cheers,
Julien

Attachment: signature.asc
Description: Digital signature


--- End Message ---
Reply to: