Am 24.01.2011 12:54, schrieb Alexander Mader:
In a follow-up I will send the config files, the crash X server log file, the gimp and the X backtrace.
You will find it attached. As in the gdm.conf the configuration file for the crashed X is xorg-X2.conf. Best regards, Alexander.
# xorg.conf (xorg X Window System server configuration file)
#
#################################################################
# Dummy
#
Section "ServerFlags"
Option "DontVTSwitch"
Option "AutoEnableDevices" "false"
EndSection
Section "ServerLayout"
Identifier "Multi"
Screen "DummyScreen"
InputDevice "Dummy Keyboard"
InputDevice "Dummy Mouse"
EndSection
Section "Screen"
Identifier "DummyScreen"
Device "Dummy"
Monitor "Standardbildschirm"
DefaultColorDepth 8
SubSection "Display"
Modes "320x240"
EndSubSection
EndSection
Section "Device"
Identifier "Dummy"
Driver "dummy"
VideoRam 75
EndSection
Section "InputDevice"
Identifier "Dummy Keyboard"
Driver "kbd"
Option "CoreKeyboard"
Option "XkbRules" "xorg"
Option "XkbModel" "pc105"
Option "XkbLayout" "de"
Option "XkbVariant" "nodeadkeys"
EndSection
Section "InputDevice"
Identifier "Dummy Mouse"
Driver "mouse"
Option "CorePointer"
Option "Device" "/dev/input/mice"
Option "Protocol" "ImPS/2"
Option "Emulate3Buttons" "true"
EndSection
#
# EOF
# xorg.conf (xorg X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
#
# Edit this file with caution, and see the xorg.conf manual page.
# (Type "man xorg.conf" at the shell prompt.)
#
# This file is automatically updated on xserver-xorg package upgrades *only*
# if it has not been modified since the last upgrade of the xserver-xorg
# package.
#
# If you have edited this file but would like it to be automatically updated
# again, run the following command:
# sudo dpkg-reconfigure -phigh xserver-xorg
#
Section "ServerFlags"
Option "DontVTSwitch"
Option "AutoEnableDevices" "false"
EndSection
Section "InputDevice"
Identifier "Generic Keyboard"
# Change the value of the "Dev Phys" option to the physical
# address of the corresponding keyboard, found in the file
# /proc/bus/input/devices .
Driver "evdev"
Option "Device" "/dev/input/by-path/platform-i8042-serio-0-event-kbd"
# Configure your keyboard as usual
Option "CoreKeyboard"
Option "XkbRules" "xorg"
Option "XkbModel" "pc105"
Option "XkbLayout" "de"
Option "XkbVariant" "nodeadkeys"
EndSection
Section "InputDevice"
Identifier "Configured Mouse"
# Change the value of the "Dev Phys" option to the physical
# address of the corresponding mouse, found in the file
# /proc/bus/input/devices .
Driver "evdev"
Option "Device" "/dev/input/by-path/pci-0000:00:12.0-usb-0:5:1.0-event-mouse"
# All mice should have "CorePointer"
Option "CorePointer"
EndSection
Section "Device"
Identifier "Standardgrafikkarte"
Driver "ati"
BusID "PCI:6:0:0"
EndSection
Section "Screen"
Identifier "Default Screen"
Device "Standardgrafikkarte"
DefaultDepth 24
EndSection
Section "ServerLayout"
Identifier "X0"
Screen "Default Screen"
InputDevice "Generic Keyboard"
InputDevice "Configured Mouse"
EndSection
# EOF
# xorg.conf (xorg X Window System server configuration file)
#
Section "ServerFlags"
Option "DontVTSwitch"
Option "AutoEnableDevices" "false"
EndSection
#################################################################
# Dritte Karte
#
Section "ServerLayout"
Identifier "X2"
Screen 0 "Screen0" 0 0
InputDevice "Keyboard0" #"CoreKeyboard"
InputDevice "USB Mouse" #"CorePointer"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
# Change the value of the "Dev Phys" option to the physical
# address of the corresponding keyboard, found in the file
# /proc/bus/input/devices .
Driver "evdev"
Option "Device" "/dev/input/by-path/pci-0000:00:16.0-usb-0:3:1.0-event-kbd"
# Configure your keyboard as usual
Option "CoreKeyboard"
Option "XkbRules" "xorg"
Option "XkbModel" "pc105"
Option "XkbLayout" "de"
Option "XkbVariant" "nodeadkeys"
EndSection
Section "InputDevice"
Identifier "USB Mouse"
# Change the value of the "Dev Phys" option to the physical
# address of the corresponding mouse, found in the file
# /proc/bus/input/devices .
Driver "evdev"
Option "Device" "/dev/input/by-path/pci-0000:00:13.0-usb-0:1:1.0-event-mouse"
# All mice should have "CorePointer"
Option "CorePointer"
EndSection
Section "Device"
Identifier "Card0"
Driver "ati"
BusID "PCI:5:0:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
DefaultColorDepth 24
EndSection
# EOF
# GDM Custom Configuration file. # # This file is the appropriate place for specifying your customizations to the # GDM configuration. If you run gdmsetup, it will automatically edit this # file for you and will cause the daemon and any running GDM GUI programs to # automatically update with the new configuration. Not all configuration # options are supported by gdmsetup, so to modify some values it may be # necessary to modify this file directly by hand. # # This file overrides the default configuration settings. These settings # are stored in the GDM System Defaults configuration file, which is found # at the following location. # # /usr/share/gdm/defaults.conf. # # This file contains comments about the meaning of each configuration option, # so is also a useful reference. Also refer to the documentation links at # the end of this comment for further information. In short, to hand-edit # this file, simply add or modify the key=value combination in the # appropriate section in the template below this comment section. # # For example, if you want to specify a different value for the Enable key # in the "[debug]" section of your GDM System Defaults configuration file, # then add "Enable=true" in the "[debug]" section of this file. If the # key already exists in this file, then simply modify it. # # Older versions of GDM used the "gdm.conf" file for configuration. If your # system has an old gdm.conf file on the system, it will be used instead of # this file - so changes made to this file will not take effect. Consider # migrating your configuration to this file and removing the gdm.conf file. # # If you hand edit a GDM configuration file, you can run the following # command and the GDM daemon will immediately reflect the change. Any # running GDM GUI programs will also be notified to update with the new # configuration. # # gdmflexiserver --command="UPDATE_CONFIG <configuration key>" # # e.g, the "Enable" key in the "[debug]" section would be "debug/Enable". # # You can also run gdm-restart or gdm-safe-restart to cause GDM to restart and # re-read the new configuration settings. You can also restart GDM by sending # a HUP or USR1 signal to the daemon. HUP behaves like gdm-restart and causes # any user session started by GDM to exit immediately while USR1 behaves like # gdm-safe-restart and will wait until all users log out before restarting GDM. # # For full reference documentation see the gnome help browser under # GNOME|System category. You can also find the docs in HTML form on # http://www.gnome.org/projects/gdm/ # # NOTE: Lines that begin with "#" are considered comments. # # Have fun! [daemon] [security] [xdmcp] [gui] [greeter] [chooser] [debug] # Note that to disable servers defined in the GDM System Defaults # configuration file (such as 0=Standard, you must put a line in this file # that says 0=inactive, as described in the Configuration section of the GDM # documentation. # [servers] 0=Multi 1=Standard 2=Second # Also note, that if you redefine a [server-foo] section, then GDM will # use the definition in this file, not the GDM System Defaults configuration # file. It is currently not possible to disable a [server-foo] section # defined in the GDM System Defaults configuration file. # [server-Multi] name=Dummy server command=/usr/bin/X -config xorg-X.conf -layout Multi -audit 0 vt7 flexible=false handled=false [server-Standard] name=Standard server command=/usr/bin/X0 -config xorg-X0.conf -layout X0 -audit 0 vt7 -noreset -sharevts -novtswitch flexible=false [server-Second] name=Second server command=/usr/bin/X1 -config xorg-X2.conf -layout X2 -audit 0 vt7 -noreset -sharevts -novtswitch flexible=false # EOF
Attachment:
Xorg.2.log.old
Description: application/trash