Bug#580989: xserver-xorg-video-intel: [855GM] LVDS output not working
On 13.10.2010 20:56, Julien Cristau wrote:
Can you also try the 2.6.36-rc kernel from experimental, to see if that
manages to light up your monitor?
No, it behaves the same. The only difference is that LVDS1 is printed as first
in logs and xrandr output, and VGA1 is printed as second. Attached dmesg and X
log (with monitor attached to DVI output). Kernel version
2.6.36~rc6-1~experimental.1, intel driver version 2:2.13.0-1.
Paweł
xrandr says:
# xrandr -d :0.0 -q
Screen 0: minimum 320 x 200, current 1024 x 768, maximum 2048 x 2048
LVDS1 connected 1024x768+0+0 (normal left inverted right x axis y axis) 0mm x 0mm
1024x768 60.0*+ 85.0 75.0 70.1 60.0* 43.5
832x624 74.6
800x600 85.1 72.2 75.0 60.3 56.2
640x480 85.0 72.8 75.0 59.9
720x400 85.0
640x400 85.1
640x350 85.1
VGA1 connected 1024x768+0+0 (normal left inverted right x axis y axis) 340mm x
270mm
1280x1024 60.0 + 75.0
1024x768 75.1 70.1 60.0*
832x624 74.6
800x600 72.2 75.0 60.3 56.2
640x480 72.8 75.0 66.7 60.0
720x400 70.1
# xrandr -d :0.0 -q --verbose
Screen 0: minimum 320 x 200, current 1024 x 768, maximum 2048 x 2048
LVDS1 connected 1024x768+0+0 (0x43) normal (normal left inverted right x axis
y axis) 0mm x 0mm
Identifier: 0x41
Timestamp: 141499
Subpixel: horizontal rgb
Clones:
CRTC: 1
CRTCs: 1
scaling mode: Full aspect
supported: None Full Center Full aspect
1024x768 (0x43) 65.0MHz -HSync -VSync *current +preferred
h: width 1024 start 1048 end 1184 total 1344 skew 0 clock 48.4KHz
v: height 768 start 771 end 777 total 806 clock 60.0Hz
1024x768 (0x44) 94.5MHz +HSync +VSync
h: width 1024 start 1072 end 1168 total 1376 skew 0 clock 68.7KHz
v: height 768 start 769 end 772 total 808 clock 85.0Hz
1024x768 (0x45) 78.8MHz +HSync +VSync
h: width 1024 start 1040 end 1136 total 1312 skew 0 clock 60.0KHz
v: height 768 start 769 end 772 total 800 clock 75.0Hz
1024x768 (0x46) 75.0MHz -HSync -VSync
h: width 1024 start 1048 end 1184 total 1328 skew 0 clock 56.5KHz
v: height 768 start 771 end 777 total 806 clock 70.1Hz
1024x768 (0x43) 65.0MHz -HSync -VSync *current
h: width 1024 start 1048 end 1184 total 1344 skew 0 clock 48.4KHz
v: height 768 start 771 end 777 total 806 clock 60.0Hz
1024x768 (0x47) 44.9MHz +HSync +VSync Interlace
h: width 1024 start 1032 end 1208 total 1264 skew 0 clock 35.5KHz
v: height 768 start 768 end 776 total 817 clock 43.5Hz
832x624 (0x48) 57.3MHz -HSync -VSync
h: width 832 start 864 end 928 total 1152 skew 0 clock 49.7KHz
v: height 624 start 625 end 628 total 667 clock 74.6Hz
800x600 (0x49) 56.3MHz +HSync +VSync
h: width 800 start 832 end 896 total 1048 skew 0 clock 53.7KHz
v: height 600 start 601 end 604 total 631 clock 85.1Hz
800x600 (0x4a) 50.0MHz +HSync +VSync
h: width 800 start 856 end 976 total 1040 skew 0 clock 48.1KHz
v: height 600 start 637 end 643 total 666 clock 72.2Hz
800x600 (0x4b) 49.5MHz +HSync +VSync
h: width 800 start 816 end 896 total 1056 skew 0 clock 46.9KHz
v: height 600 start 601 end 604 total 625 clock 75.0Hz
800x600 (0x4c) 40.0MHz +HSync +VSync
h: width 800 start 840 end 968 total 1056 skew 0 clock 37.9KHz
v: height 600 start 601 end 605 total 628 clock 60.3Hz
800x600 (0x4d) 36.0MHz +HSync +VSync
h: width 800 start 824 end 896 total 1024 skew 0 clock 35.2KHz
v: height 600 start 601 end 603 total 625 clock 56.2Hz
640x480 (0x4e) 36.0MHz -HSync -VSync
h: width 640 start 696 end 752 total 832 skew 0 clock 43.3KHz
v: height 480 start 481 end 484 total 509 clock 85.0Hz
640x480 (0x4f) 31.5MHz -HSync -VSync
h: width 640 start 664 end 704 total 832 skew 0 clock 37.9KHz
v: height 480 start 489 end 492 total 520 clock 72.8Hz
640x480 (0x50) 31.5MHz -HSync -VSync
h: width 640 start 656 end 720 total 840 skew 0 clock 37.5KHz
v: height 480 start 481 end 484 total 500 clock 75.0Hz
640x480 (0x51) 25.2MHz -HSync -VSync
h: width 640 start 656 end 752 total 800 skew 0 clock 31.5KHz
v: height 480 start 490 end 492 total 525 clock 59.9Hz
720x400 (0x52) 35.5MHz -HSync +VSync
h: width 720 start 756 end 828 total 936 skew 0 clock 37.9KHz
v: height 400 start 401 end 404 total 446 clock 85.0Hz
640x400 (0x53) 31.5MHz -HSync +VSync
h: width 640 start 672 end 736 total 832 skew 0 clock 37.9KHz
v: height 400 start 401 end 404 total 445 clock 85.1Hz
640x350 (0x54) 31.5MHz +HSync -VSync
h: width 640 start 672 end 736 total 832 skew 0 clock 37.9KHz
v: height 350 start 382 end 385 total 445 clock 85.1Hz
VGA1 connected 1024x768+0+0 (0x43) normal (normal left inverted right x axis y
axis) 340mm x 270mm
Identifier: 0x42
Timestamp: 141499
Subpixel: unknown
Clones:
CRTC: 0
CRTCs: 0 1
1280x1024 (0x55) 108.0MHz +HSync +VSync +preferred
h: width 1280 start 1328 end 1440 total 1688 skew 0 clock 64.0KHz
v: height 1024 start 1025 end 1028 total 1066 clock 60.0Hz
1280x1024 (0x56) 135.0MHz +HSync +VSync
h: width 1280 start 1296 end 1440 total 1688 skew 0 clock 80.0KHz
v: height 1024 start 1025 end 1028 total 1066 clock 75.0Hz
1024x768 (0x57) 78.8MHz +HSync +VSync
h: width 1024 start 1040 end 1136 total 1312 skew 0 clock 60.1KHz
v: height 768 start 769 end 772 total 800 clock 75.1Hz
1024x768 (0x46) 75.0MHz -HSync -VSync
h: width 1024 start 1048 end 1184 total 1328 skew 0 clock 56.5KHz
v: height 768 start 771 end 777 total 806 clock 70.1Hz
1024x768 (0x43) 65.0MHz -HSync -VSync *current
h: width 1024 start 1048 end 1184 total 1344 skew 0 clock 48.4KHz
v: height 768 start 771 end 777 total 806 clock 60.0Hz
832x624 (0x48) 57.3MHz -HSync -VSync
h: width 832 start 864 end 928 total 1152 skew 0 clock 49.7KHz
v: height 624 start 625 end 628 total 667 clock 74.6Hz
800x600 (0x4a) 50.0MHz +HSync +VSync
h: width 800 start 856 end 976 total 1040 skew 0 clock 48.1KHz
v: height 600 start 637 end 643 total 666 clock 72.2Hz
800x600 (0x4b) 49.5MHz +HSync +VSync
h: width 800 start 816 end 896 total 1056 skew 0 clock 46.9KHz
v: height 600 start 601 end 604 total 625 clock 75.0Hz
800x600 (0x4c) 40.0MHz +HSync +VSync
h: width 800 start 840 end 968 total 1056 skew 0 clock 37.9KHz
v: height 600 start 601 end 605 total 628 clock 60.3Hz
800x600 (0x4d) 36.0MHz +HSync +VSync
h: width 800 start 824 end 896 total 1024 skew 0 clock 35.2KHz
v: height 600 start 601 end 603 total 625 clock 56.2Hz
640x480 (0x58) 31.5MHz -HSync -VSync
h: width 640 start 664 end 704 total 832 skew 0 clock 37.9KHz
v: height 480 start 489 end 491 total 520 clock 72.8Hz
640x480 (0x50) 31.5MHz -HSync -VSync
h: width 640 start 656 end 720 total 840 skew 0 clock 37.5KHz
v: height 480 start 481 end 484 total 500 clock 75.0Hz
640x480 (0x59) 30.2MHz -HSync -VSync
h: width 640 start 704 end 768 total 864 skew 0 clock 35.0KHz
v: height 480 start 483 end 486 total 525 clock 66.7Hz
640x480 (0x5a) 25.2MHz -HSync -VSync
h: width 640 start 656 end 752 total 800 skew 0 clock 31.5KHz
v: height 480 start 490 end 492 total 525 clock 60.0Hz
720x400 (0x5b) 28.3MHz -HSync +VSync
h: width 720 start 738 end 846 total 900 skew 0 clock 31.5KHz
v: height 400 start 412 end 414 total 449 clock 70.1Hz
X.Org X Server 1.7.7
Release Date: 2010-05-04
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.32.23-dsa-ia32 i686 Debian
Current Operating System: Linux kontron 2.6.36-rc6-686 #1 SMP Mon Oct 4 10:25:13 UTC 2010 i686
Kernel command line: root=UUID=6d1a49a2-4622-40cb-b080-e5efe0c62d57 ro
Build Date: 10 October 2010 11:57:07AM
xorg-server 2:1.7.7-8 (Cyril Brulebois <kibi@debian.org>)
Current version of pixman: 0.16.4
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Wed Oct 13 21:07:34 2010
(==) Using config file: "/etc/X11/xorg.conf"
(==) Using system config directory "/usr/share/X11/xorg.conf.d"
(==) No Layout section. Using the first Screen section.
(**) |-->Screen "Default Screen" (0)
(**) | |-->Monitor "Configured Monitor"
(==) No device specified for screen "Default Screen".
Using the first device section listed.
(**) | |-->Device "Configured Video Device"
(==) Automatically adding devices
(==) Automatically enabling devices
(WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
Entry deleted from font path.
(WW) The directory "/usr/share/fonts/X11/100dpi/" does not exist.
Entry deleted from font path.
(WW) The directory "/usr/share/fonts/X11/75dpi/" does not exist.
Entry deleted from font path.
(WW) The directory "/usr/share/fonts/X11/Type1" does not exist.
Entry deleted from font path.
(WW) The directory "/usr/share/fonts/X11/100dpi" does not exist.
Entry deleted from font path.
(WW) The directory "/usr/share/fonts/X11/75dpi" does not exist.
Entry deleted from font path.
(==) FontPath set to:
/usr/share/fonts/X11/misc,
/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType,
built-ins
(==) ModulePath set to "/usr/lib/xorg/modules"
(II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
(II) Loader magic: 0x81ecca0
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.4
X.Org Video Driver: 6.0
X.Org XInput driver : 7.0
X.Org Server Extension : 2.0
(--) using VT number 7
(--) PCI:*(0:0:2:0) 8086:3582:8086:1968 Intel Corporation 82852/855GM Integrated Graphics Device rev 2, Mem @ 0xf0000000/134217728, 0xfe980000/524288, I/O @ 0x0000df80/8
(--) PCI: (0:0:2:1) 8086:3582:8086:1968 Intel Corporation 82852/855GM Integrated Graphics Device rev 2, Mem @ 0xe8000000/134217728, 0xfe880000/524288
(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.7.7, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension SELinux
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.7.7, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions/libglx.so
(II) Module glx: vendor="X.Org Foundation"
compiled for 1.7.7, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions/librecord.so
(II) Module record: vendor="X.Org Foundation"
compiled for 1.7.7, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension RECORD
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions/libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.7.7, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "dri2"
(II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
compiled for 1.7.7, module version = 1.1.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(==) Matched intel as autoconfigured driver 0
(==) Matched vesa as autoconfigured driver 1
(==) Matched fbdev as autoconfigured driver 2
(==) Assigned the driver to the xf86ConfigLayout
(II) LoadModule: "intel"
(II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
(II) Module intel: vendor="X.Org Foundation"
compiled for 1.7.7, module version = 2.13.0
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 6.0
(II) LoadModule: "vesa"
(II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so
(II) Module vesa: vendor="X.Org Foundation"
compiled for 1.7.7, module version = 2.3.0
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 6.0
(II) LoadModule: "fbdev"
(II) Loading /usr/lib/xorg/modules/drivers/fbdev_drv.so
(II) Module fbdev: vendor="X.Org Foundation"
compiled for 1.7.6.901, module version = 0.4.2
ABI class: X.Org Video Driver, version 6.0
(II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G,
965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45,
4 Series, G45/G43, Q45/Q43, G41, B43, B43, Clarkdale, Arrandale,
Sandybridge, Sandybridge, Sandybridge, Sandybridge, Sandybridge,
Sandybridge, Sandybridge
(II) VESA: driver for VESA chipsets: vesa
(II) FBDEV: driver for framebuffer: fbdev
(II) Primary Device is: PCI 00@00:02:0
(WW) Falling back to old probe method for vesa
(WW) Falling back to old probe method for fbdev
(II) Loading sub module "fbdevhw"
(II) LoadModule: "fbdevhw"
(II) Loading /usr/lib/xorg/modules/linux/libfbdevhw.so
(II) Module fbdevhw: vendor="X.Org Foundation"
compiled for 1.7.7, module version = 0.0.2
ABI class: X.Org Video Driver, version 6.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 10, (OK)
drmOpenByBusid: Searching for BusID pci:0000:00:02.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 10, (OK)
drmOpenByBusid: drmOpenMinor returns 10
drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
(II) intel(0): Creating default Display subsection in Screen section
"Default Screen" for depth/fbbpp 24/32
(==) intel(0): Depth 24, (--) framebuffer bpp 32
(==) intel(0): RGB weight 888
(==) intel(0): Default visual is TrueColor
(II) intel(0): Integrated Graphics Chipset: Intel(R) 855GME
(--) intel(0): Chipset: "852GM/855GM"
(**) intel(0): Tiling enabled
(**) intel(0): SwapBuffers wait enabled
(==) intel(0): video overlay key set to 0x101fe
(II) intel(0): Output LVDS1 using monitor section Configured Monitor
(II) intel(0): Output VGA1 has no monitor section
(II) intel(0): EDID for output LVDS1
(II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
(II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
(II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
(II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
(II) intel(0): Not using default mode "640x480" (doublescan mode not supported)
(II) intel(0): Not using default mode "640x512" (doublescan mode not supported)
(II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
(II) intel(0): Not using default mode "896x672" (doublescan mode not supported)
(II) intel(0): Not using default mode "928x696" (doublescan mode not supported)
(II) intel(0): Not using default mode "960x720" (doublescan mode not supported)
(II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
(II) intel(0): Not using default mode "680x384" (doublescan mode not supported)
(II) intel(0): Not using default mode "680x384" (doublescan mode not supported)
(II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
(II) intel(0): Not using default mode "720x450" (doublescan mode not supported)
(II) intel(0): Not using default mode "800x512" (doublescan mode not supported)
(II) intel(0): Not using default mode "840x525" (doublescan mode not supported)
(II) intel(0): Not using default mode "840x525" (doublescan mode not supported)
(II) intel(0): Not using default mode "960x540" (doublescan mode not supported)
(II) intel(0): Not using default mode "960x600" (doublescan mode not supported)
(II) intel(0): Not using default mode "320x175" (doublescan mode not supported)
(II) intel(0): Not using default mode "320x200" (doublescan mode not supported)
(II) intel(0): Not using default mode "360x200" (doublescan mode not supported)
(II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
(II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
(II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
(II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
(II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
(II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
(II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
(II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
(II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
(II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
(II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
(II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
(II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
(II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
(II) intel(0): Not using default mode "1152x864" (exceeds panel dimensions)
(II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
(II) intel(0): Not using default mode "1280x960" (exceeds panel dimensions)
(II) intel(0): Not using default mode "640x480" (doublescan mode not supported)
(II) intel(0): Not using default mode "1280x960" (exceeds panel dimensions)
(II) intel(0): Not using default mode "640x480" (doublescan mode not supported)
(II) intel(0): Not using default mode "1280x1024" (exceeds panel dimensions)
(II) intel(0): Not using default mode "640x512" (doublescan mode not supported)
(II) intel(0): Not using default mode "1280x1024" (exceeds panel dimensions)
(II) intel(0): Not using default mode "640x512" (doublescan mode not supported)
(II) intel(0): Not using default mode "1280x1024" (hsync out of range)
(II) intel(0): Not using default mode "640x512" (doublescan mode not supported)
(II) intel(0): Not using default mode "1600x1200" (exceeds panel dimensions)
(II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
(II) intel(0): Not using default mode "1600x1200" (exceeds panel dimensions)
(II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
(II) intel(0): Not using default mode "1600x1200" (exceeds panel dimensions)
(II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
(II) intel(0): Not using default mode "1600x1200" (hsync out of range)
(II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
(II) intel(0): Not using default mode "1600x1200" (hsync out of range)
(II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
(II) intel(0): Not using default mode "1792x1344" (exceeds panel dimensions)
(II) intel(0): Not using default mode "896x672" (doublescan mode not supported)
(II) intel(0): Not using default mode "1792x1344" (hsync out of range)
(II) intel(0): Not using default mode "896x672" (doublescan mode not supported)
(II) intel(0): Not using default mode "1856x1392" (exceeds panel dimensions)
(II) intel(0): Not using default mode "928x696" (doublescan mode not supported)
(II) intel(0): Not using default mode "1856x1392" (hsync out of range)
(II) intel(0): Not using default mode "928x696" (doublescan mode not supported)
(II) intel(0): Not using default mode "1920x1440" (exceeds panel dimensions)
(II) intel(0): Not using default mode "960x720" (doublescan mode not supported)
(II) intel(0): Not using default mode "1920x1440" (hsync out of range)
(II) intel(0): Not using default mode "960x720" (doublescan mode not supported)
(II) intel(0): Not using default mode "416x312" (doublescan mode not supported)
(II) intel(0): Not using default mode "1152x864" (exceeds panel dimensions)
(II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
(II) intel(0): Not using default mode "1152x864" (exceeds panel dimensions)
(II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
(II) intel(0): Not using default mode "1152x864" (exceeds panel dimensions)
(II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
(II) intel(0): Not using default mode "1152x864" (exceeds panel dimensions)
(II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
(II) intel(0): Not using default mode "1152x864" (exceeds panel dimensions)
(II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
(II) intel(0): Not using default mode "1152x864" (hsync out of range)
(II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
(II) intel(0): Not using default mode "1360x768" (monitor doesn't support reduced blanking)
(II) intel(0): Not using default mode "680x384" (doublescan mode not supported)
(II) intel(0): Not using default mode "1360x768" (exceeds panel dimensions)
(II) intel(0): Not using default mode "680x384" (doublescan mode not supported)
(II) intel(0): Not using default mode "1400x1050" (exceeds panel dimensions)
(II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
(II) intel(0): Not using default mode "1400x1050" (exceeds panel dimensions)
(II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
(II) intel(0): Not using default mode "1400x1050" (exceeds panel dimensions)
(II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
(II) intel(0): Not using default mode "1400x1050" (hsync out of range)
(II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
(II) intel(0): Not using default mode "1440x900" (exceeds panel dimensions)
(II) intel(0): Not using default mode "720x450" (doublescan mode not supported)
(II) intel(0): Not using default mode "1600x1024" (exceeds panel dimensions)
(II) intel(0): Not using default mode "800x512" (doublescan mode not supported)
(II) intel(0): Not using default mode "1680x1050" (monitor doesn't support reduced blanking)
(II) intel(0): Not using default mode "840x525" (doublescan mode not supported)
(II) intel(0): Not using default mode "1680x1050" (exceeds panel dimensions)
(II) intel(0): Not using default mode "840x525" (doublescan mode not supported)
(II) intel(0): Not using default mode "1680x1050" (exceeds panel dimensions)
(II) intel(0): Not using default mode "840x525" (doublescan mode not supported)
(II) intel(0): Not using default mode "1680x1050" (exceeds panel dimensions)
(II) intel(0): Not using default mode "840x525" (doublescan mode not supported)
(II) intel(0): Not using default mode "1680x1050" (hsync out of range)
(II) intel(0): Not using default mode "840x525" (doublescan mode not supported)
(II) intel(0): Not using default mode "1920x1080" (monitor doesn't support reduced blanking)
(II) intel(0): Not using default mode "960x540" (doublescan mode not supported)
(II) intel(0): Not using default mode "1920x1200" (monitor doesn't support reduced blanking)
(II) intel(0): Not using default mode "960x600" (doublescan mode not supported)
(II) intel(0): Not using default mode "1920x1440" (hsync out of range)
(II) intel(0): Not using default mode "960x720" (doublescan mode not supported)
(II) intel(0): Not using default mode "2048x1536" (hsync out of range)
(II) intel(0): Not using default mode "1024x768" (doublescan mode not supported)
(II) intel(0): Not using default mode "2048x1536" (hsync out of range)
(II) intel(0): Not using default mode "1024x768" (doublescan mode not supported)
(II) intel(0): Not using default mode "2048x1536" (hsync out of range)
(II) intel(0): Not using default mode "1024x768" (doublescan mode not supported)
(II) intel(0): Printing probed modes for output LVDS1
(II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
(II) intel(0): Modeline "1024x768"x85.0 94.50 1024 1072 1168 1376 768 769 772 808 +hsync +vsync (68.7 kHz)
(II) intel(0): Modeline "1024x768"x75.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz)
(II) intel(0): Modeline "1024x768"x70.1 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz)
(II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
(II) intel(0): Modeline "1024x768"x87.0 44.90 1024 1032 1208 1264 768 768 776 817 interlace +hsync +vsync (35.5 kHz)
(II) intel(0): Modeline "832x624"x74.6 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz)
(II) intel(0): Modeline "800x600"x85.1 56.30 800 832 896 1048 600 601 604 631 +hsync +vsync (53.7 kHz)
(II) intel(0): Modeline "800x600"x72.2 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz)
(II) intel(0): Modeline "800x600"x75.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz)
(II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
(II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
(II) intel(0): Modeline "640x480"x85.0 36.00 640 696 752 832 480 481 484 509 -hsync -vsync (43.3 kHz)
(II) intel(0): Modeline "640x480"x72.8 31.50 640 664 704 832 480 489 492 520 -hsync -vsync (37.9 kHz)
(II) intel(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz)
(II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
(II) intel(0): Modeline "720x400"x85.0 35.50 720 756 828 936 400 401 404 446 -hsync +vsync (37.9 kHz)
(II) intel(0): Modeline "640x400"x85.1 31.50 640 672 736 832 400 401 404 445 -hsync +vsync (37.9 kHz)
(II) intel(0): Modeline "640x350"x85.1 31.50 640 672 736 832 350 382 385 445 +hsync -vsync (37.9 kHz)
(II) intel(0): EDID for output VGA1
(II) intel(0): Manufacturer: AOC Model: 1719 Serial#: 144
(II) intel(0): Year: 2010 Week: 31
(II) intel(0): EDID Version: 1.3
(II) intel(0): Digital Display Input
(II) intel(0): Max Image Size [cm]: horiz.: 34 vert.: 27
(II) intel(0): Gamma: 2.20
(II) intel(0): DPMS capabilities: Off
(II) intel(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
(II) intel(0): First detailed timing is preferred mode
(II) intel(0): redX: 0.637 redY: 0.347 greenX: 0.275 greenY: 0.613
(II) intel(0): blueX: 0.143 blueY: 0.090 whiteX: 0.300 whiteY: 0.335
(II) intel(0): Supported established timings:
(II) intel(0): 720x400@70Hz
(II) intel(0): 640x480@60Hz
(II) intel(0): 640x480@67Hz
(II) intel(0): 640x480@72Hz
(II) intel(0): 640x480@75Hz
(II) intel(0): 800x600@56Hz
(II) intel(0): 800x600@60Hz
(II) intel(0): 800x600@72Hz
(II) intel(0): 800x600@75Hz
(II) intel(0): 832x624@75Hz
(II) intel(0): 1024x768@60Hz
(II) intel(0): 1024x768@70Hz
(II) intel(0): 1024x768@75Hz
(II) intel(0): 1280x1024@75Hz
(II) intel(0): Manufacturer's mask: 0
(II) intel(0): Supported standard timings:
(II) intel(0): #0: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
(II) intel(0): Supported detailed timing:
(II) intel(0): clock: 108.0 MHz Image Size: 340 x 270 mm
(II) intel(0): h_active: 1280 h_sync: 1328 h_sync_end 1440 h_blank_end 1688 h_border: 0
(II) intel(0): v_active: 1024 v_sync: 1025 v_sync_end 1028 v_blanking: 1066 v_border: 0
(II) intel(0): Serial No: X90A8JA000144
(II) intel(0): Ranges: V min: 55 V max: 75 Hz, H min: 30 H max: 83 kHz, PixClock max 145 MHz
(II) intel(0): Monitor name: 1719
(II) intel(0): EDID (in hex):
(II) intel(0): 00ffffffffffff0005e3191790000000
(II) intel(0): 1f140103e8221b782a388fa358469d24
(II) intel(0): 174c55bfef0081800101010101010101
(II) intel(0): 010101010101302a009851002a403070
(II) intel(0): 1300540e1100001e000000ff00583930
(II) intel(0): 41384a41303030313434000000fd0037
(II) intel(0): 4b1e530e000a202020202020000000fc
(II) intel(0): 00313731390a202020202020202000a4
(II) intel(0): Printing probed modes for output VGA1
(II) intel(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) intel(0): Modeline "1280x1024"x75.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) intel(0): Modeline "1024x768"x75.1 78.80 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.1 kHz)
(II) intel(0): Modeline "1024x768"x70.1 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz)
(II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
(II) intel(0): Modeline "832x624"x74.6 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz)
(II) intel(0): Modeline "800x600"x72.2 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz)
(II) intel(0): Modeline "800x600"x75.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz)
(II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
(II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
(II) intel(0): Modeline "640x480"x72.8 31.50 640 664 704 832 480 489 491 520 -hsync -vsync (37.9 kHz)
(II) intel(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz)
(II) intel(0): Modeline "640x480"x66.7 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz)
(II) intel(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
(II) intel(0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
(II) intel(0): Output LVDS1 connected
(II) intel(0): Output VGA1 connected
(II) intel(0): Using exact sizes for initial modes
(II) intel(0): Output LVDS1 using initial mode 1024x768
(II) intel(0): Output VGA1 using initial mode 1024x768
(II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
(II) intel(0): Kernel page flipping support detected, enabling
(==) intel(0): DPI set to (96, 96)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules/libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 1.7.7, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.4
(II) UnloadModule: "vesa"
(II) Unloading /usr/lib/xorg/modules/drivers/vesa_drv.so
(II) UnloadModule: "fbdev"
(II) Unloading /usr/lib/xorg/modules/drivers/fbdev_drv.so
(II) UnloadModule: "fbdevhw"
(II) Unloading /usr/lib/xorg/modules/linux/libfbdevhw.so
(==) Depth 24 pixmap format is 32 bpp
(==) intel(0): VideoRam: 131072 KB
(II) intel(0): [DRI2] Setup complete
(II) intel(0): Allocated new frame buffer 1024x768 stride 4096, tiled
(II) UXA(0): Driver registered support for the following operations:
(II) solid
(II) copy
(II) composite (RENDER acceleration)
(II) put_image
(II) get_image
(==) intel(0): Backing store disabled
(==) intel(0): Silken mouse enabled
(II) intel(0): Initializing HW Cursor
(II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
(==) intel(0): DPMS enabled
(==) intel(0): Intel XvMC decoder disabled
(II) intel(0): Set up overlay video
(II) intel(0): direct rendering: DRI2 Enabled
(--) RandR disabled
(II) Initializing built-in extension Generic Event Extension
(II) Initializing built-in extension SHAPE
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension BIG-REQUESTS
(II) Initializing built-in extension SYNC
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-MISC
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
SELinux: Disabled on system, not enabling in X server
(II) AIGLX: enabled GLX_MESA_copy_sub_buffer
(II) AIGLX: enabled GLX_SGI_make_current_read
(II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
(II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
(II) AIGLX: Loaded and initialized /usr/lib/dri/i915_dri.so
(II) GLX: Initialized DRI2 GL provider for screen 0
(II) intel(0): Setting screen physical size to 270 x 203
(II) config/udev: Adding input device Power Button (/dev/input/event4)
(**) Power Button: Applying InputClass "evdev keyboard catchall"
(II) LoadModule: "evdev"
(II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
(II) Module evdev: vendor="X.Org Foundation"
compiled for 1.7.6.901, module version = 2.3.2
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 7.0
(**) Power Button: always reports core events
(**) Power Button: Device: "/dev/input/event4"
(II) Power Button: Found keys
(II) Power Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "pc104"
(**) Option "xkb_layout" "us"
(II) config/udev: Adding input device Power Button (/dev/input/event3)
(**) Power Button: Applying InputClass "evdev keyboard catchall"
(**) Power Button: always reports core events
(**) Power Button: Device: "/dev/input/event3"
(II) Power Button: Found keys
(II) Power Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "pc104"
(**) Option "xkb_layout" "us"
(II) config/udev: Adding input device HID 173d:0004 (/dev/input/event0)
(**) HID 173d:0004: Applying InputClass "evdev keyboard catchall"
(**) HID 173d:0004: always reports core events
(**) HID 173d:0004: Device: "/dev/input/event0"
(II) HID 173d:0004: Found keys
(II) HID 173d:0004: Configuring as keyboard
(II) XINPUT: Adding extended input device "HID 173d:0004" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "pc104"
(**) Option "xkb_layout" "us"
(II) config/udev: Adding input device HID 173d:0004 (/dev/input/event1)
(**) HID 173d:0004: Applying InputClass "evdev keyboard catchall"
(**) HID 173d:0004: always reports core events
(**) HID 173d:0004: Device: "/dev/input/event1"
(II) HID 173d:0004: Found keys
(II) HID 173d:0004: Configuring as keyboard
(II) XINPUT: Adding extended input device "HID 173d:0004" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "pc104"
(**) Option "xkb_layout" "us"
(II) config/udev: Adding input device PIXART USB OPTICAL MOUSE (/dev/input/event2)
(**) PIXART USB OPTICAL MOUSE: Applying InputClass "evdev pointer catchall"
(**) PIXART USB OPTICAL MOUSE: always reports core events
(**) PIXART USB OPTICAL MOUSE: Device: "/dev/input/event2"
(II) PIXART USB OPTICAL MOUSE: Found 3 mouse buttons
(II) PIXART USB OPTICAL MOUSE: Found scroll wheel(s)
(II) PIXART USB OPTICAL MOUSE: Found relative axes
(II) PIXART USB OPTICAL MOUSE: Found x and y relative axes
(II) PIXART USB OPTICAL MOUSE: Configuring as mouse
(**) PIXART USB OPTICAL MOUSE: YAxisMapping: buttons 4 and 5
(**) PIXART USB OPTICAL MOUSE: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "PIXART USB OPTICAL MOUSE" (type: MOUSE)
(II) PIXART USB OPTICAL MOUSE: initialized for relative axes.
(II) config/udev: Adding input device PIXART USB OPTICAL MOUSE (/dev/input/mouse0)
(II) No input driver/identifier specified (ignoring)
(II) config/udev: Adding input device PC Speaker (/dev/input/event5)
(II) No input driver/identifier specified (ignoring)
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.36-rc6-686 (Debian 2.6.36~rc6-1~experimental.1) (ben@decadent.org.uk) (gcc version 4.4.5 20100902 (prerelease) (Debian 4.4.4-13) ) #1 SMP Mon Oct 4 10:25:13 UTC 2010
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000000f7f0000 (usable)
[ 0.000000] BIOS-e820: 000000000f7f0000 - 000000000f7fe000 (ACPI data)
[ 0.000000] BIOS-e820: 000000000f7fe000 - 000000000f800000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000feff0000 - 00000000ff000000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
[ 0.000000] Notice: NX (Execute Disable) protection missing in CPU or disabled in BIOS!
[ 0.000000] DMI present.
[ 0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working around it.
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 update range: 0000000000000000 - 0000000000001000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] last_pfn = 0xf7f0 max_arch_pfn = 0x100000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-DFFFF uncachable
[ 0.000000] E0000-E3FFF write-protect
[ 0.000000] E4000-EFFFF write-through
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask FF0000000 write-back
[ 0.000000] 1 base 00F800000 mask FFF800000 uncachable
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] PAT not supported by CPU.
[ 0.000000] initial memory mapped : 0 - 01800000
[ 0.000000] found SMP MP-table at [c00ff780] ff780
[ 0.000000] init_memory_mapping: 0000000000000000-000000000f7f0000
[ 0.000000] 0000000000 - 0000400000 page 4k
[ 0.000000] 0000400000 - 000f400000 page 2M
[ 0.000000] 000f400000 - 000f7f0000 page 4k
[ 0.000000] kernel direct mapping tables up to f7f0000 @ 15000-1a000
[ 0.000000] RAMDISK: 0f0d0000 - 0f7e0000
[ 0.000000] ACPI: RSDP 000f80b0 00014 (v00 ACPIAM)
[ 0.000000] ACPI: RSDT 0f7f0000 00030 (v01 A M I OEMRSDT 05000711 MSFT 00000097)
[ 0.000000] ACPI: FACP 0f7f0200 00084 (v02 A M I OEMFACP 05000711 MSFT 00000097)
[ 0.000000] ACPI: DSDT 0f7f03f0 0311C (v01 TIOPI TIOPI108 00000108 INTL 20051117)
[ 0.000000] ACPI: FACS 0f7fe000 00040
[ 0.000000] ACPI: APIC 0f7f0390 00054 (v01 A M I OEMAPIC 05000711 MSFT 00000097)
[ 0.000000] ACPI: OEMB 0f7fe040 00060 (v01 A M I AMI_OEM 05000711 MSFT 00000097)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 247MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 0f7f0000
[ 0.000000] low ram: 0 - 0f7f0000
[ 0.000000] node 0 low ram: 00000000 - 0f7f0000
[ 0.000000] node 0 bootmap 00016000 - 00017f00
[ 0.000000] (13/32 early reservations) ==> bootmem [0000000000 - 000f7f0000]
[ 0.000000] #0 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
[ 0.000000] #1 [0001000000 - 00014e2ab0] TEXT DATA BSS ==> [0001000000 - 00014e2ab0]
[ 0.000000] #2 [000f0d0000 - 000f7e0000] RAMDISK ==> [000f0d0000 - 000f7e0000]
[ 0.000000] #3 [00014e3000 - 00014e90b5] BRK ==> [00014e3000 - 00014e90b5]
[ 0.000000] #4 [00000ff790 - 0000100000] BIOS reserved ==> [00000ff790 - 0000100000]
[ 0.000000] #5 [00000ff780 - 00000ff790] MP-table mpf ==> [00000ff780 - 00000ff790]
[ 0.000000] #6 [000009fc00 - 00000faa40] BIOS reserved ==> [000009fc00 - 00000faa40]
[ 0.000000] #7 [00000fab48 - 00000ff780] BIOS reserved ==> [00000fab48 - 00000ff780]
[ 0.000000] #8 [00000faa40 - 00000fab48] MP-table mpc ==> [00000faa40 - 00000fab48]
[ 0.000000] #9 [0000010000 - 0000011000] TRAMPOLINE ==> [0000010000 - 0000011000]
[ 0.000000] #10 [0000011000 - 0000015000] ACPI WAKEUP ==> [0000011000 - 0000015000]
[ 0.000000] #11 [0000015000 - 0000016000] PGTABLE ==> [0000015000 - 0000016000]
[ 0.000000] #12 [0000016000 - 0000018000] BOOTMAP ==> [0000016000 - 0000018000]
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x0000f7f0
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0000f7f0
[ 0.000000] On node 0 totalpages: 63359
[ 0.000000] free_area_init_node: node 0, pgdat c13bfe80, node_mem_map c14eb200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3951 pages, LIFO batch:0
[ 0.000000] Normal zone: 464 pages used for memmap
[ 0.000000] Normal zone: 58912 pages, LIFO batch:15
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at f800000 (gap: f800000:ef600000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:1 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 13 pages/cpu @c1800000 s31424 r0 d21824 u4194304
[ 0.000000] pcpu-alloc: s31424 r0 d21824 u4194304 alloc=1*4194304
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 62863
[ 0.000000] Kernel command line: root=UUID=6d1a49a2-4622-40cb-b080-e5efe0c62d57 ro
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] Initializing HighMem for node 0 (00000000:00000000)
[ 0.000000] Memory: 238892k/253888k available (2568k kernel code, 14544k reserved, 1304k data, 388k init, 0k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xffd36000 - 0xfffff000 (2852 kB)
[ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.000000] vmalloc : 0xcfff0000 - 0xff7fe000 ( 760 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xcf7f0000 ( 247 MB)
[ 0.000000] .init : 0xc13c9000 - 0xc142a000 ( 388 kB)
[ 0.000000] .data : 0xc12823bc - 0xc13c87b0 (1304 kB)
[ 0.000000] .text : 0xc1000000 - 0xc12823bc (2568 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:1280
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 599.973 MHz processor.
[ 0.004008] Calibrating delay loop (skipped), value calculated using timer frequency.. 1199.94 BogoMIPS (lpj=2399892)
[ 0.004128] pid_max: default: 32768 minimum: 301
[ 0.004229] Security Framework initialized
[ 0.004292] SELinux: Disabled at boot.
[ 0.004368] Mount-cache hash table entries: 512
[ 0.004750] Initializing cgroup subsys ns
[ 0.004811] Initializing cgroup subsys cpuacct
[ 0.004875] Initializing cgroup subsys devices
[ 0.004933] Initializing cgroup subsys freezer
[ 0.004990] Initializing cgroup subsys net_cls
[ 0.005048] Initializing cgroup subsys blkio
[ 0.005198] mce: CPU supports 5 MCE banks
[ 0.005270] CPU0: Thermal monitoring enabled (TM1)
[ 0.005340] Performance Events: p6 PMU driver.
[ 0.005464] ... version: 0
[ 0.005520] ... bit width: 32
[ 0.005577] ... generic registers: 2
[ 0.005633] ... value mask: 00000000ffffffff
[ 0.005691] ... max period: 000000007fffffff
[ 0.005750] ... fixed-purpose events: 0
[ 0.005806] ... event mask: 0000000000000003
[ 0.006732] SMP alternatives: switching to UP code
[ 0.017587] Freeing SMP alternatives: 16k freed
[ 0.017658] ACPI: Core revision 20100702
[ 0.028123] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.028659] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.070949] CPU0: Intel(R) Celeron(R) M processor 600MHz stepping 05
[ 0.072000] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.072000] Brought up 1 CPUs
[ 0.072000] Total of 1 processors activated (1199.94 BogoMIPS).
[ 0.072000] devtmpfs: initialized
[ 0.072000] regulator: core version 0.5
[ 0.072000] NET: Registered protocol family 16
[ 0.072000] ACPI: bus type pci registered
[ 0.072000] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=1
[ 0.072000] PCI: Using configuration type 1 for base access
[ 0.072895] bio: create slab <bio-0> at 0
[ 0.074938] ACPI: EC: Look up EC in DSDT
[ 0.077467] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.083248] ACPI: Interpreter enabled
[ 0.083310] ACPI: (supports S0 S1 S5)
[ 0.083502] ACPI: Using IOAPIC for interrupt routing
[ 0.096940] ACPI Warning: Incorrect checksum in table [OEMB] - 0x2A, should be 0x27 (20100702/tbutils-314)
[ 0.097354] ACPI: No dock devices found.
[ 0.097416] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[ 0.097795] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.098418] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored)
[ 0.098429] pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] (ignored)
[ 0.098440] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
[ 0.098451] pci_root PNP0A03:00: host bridge window [mem 0x000d0000-0x000dffff] (ignored)
[ 0.098462] pci_root PNP0A03:00: host bridge window [mem 0x0f800000-0xffffffff] (ignored)
[ 0.098705] pci 0000:00:02.0: reg 10: [mem 0xf0000000-0xf7ffffff pref]
[ 0.098721] pci 0000:00:02.0: reg 14: [mem 0xfe980000-0xfe9fffff]
[ 0.098737] pci 0000:00:02.0: reg 18: [io 0xdf80-0xdf87]
[ 0.098784] pci 0000:00:02.0: supports D1
[ 0.098821] pci 0000:00:02.1: reg 10: [mem 0xe8000000-0xefffffff pref]
[ 0.098837] pci 0000:00:02.1: reg 14: [mem 0xfe880000-0xfe8fffff]
[ 0.098890] pci 0000:00:02.1: supports D1
[ 0.099009] pci 0000:00:1d.0: reg 20: [io 0xdf00-0xdf1f]
[ 0.099114] pci 0000:00:1d.1: reg 20: [io 0xde80-0xde9f]
[ 0.099215] pci 0000:00:1d.2: reg 20: [io 0xde00-0xde1f]
[ 0.099302] pci 0000:00:1d.7: reg 10: [mem 0xfe977c00-0xfe977fff]
[ 0.099403] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.099414] pci 0000:00:1d.7: PME# disabled
[ 0.099499] * The chipset may have PM-Timer Bug. Due to workarounds for a bug,
[ 0.099504] * this clock source is slow. If you are sure your timer does not have
[ 0.099508] * this bug, please use "acpi_pm_good" to disable the workaround
[ 0.099788] pci 0000:00:1f.0: quirk: [io 0x0800-0x087f] claimed by ICH4 ACPI/GPIO/TCO
[ 0.099869] pci 0000:00:1f.0: quirk: [io 0x0480-0x04bf] claimed by ICH4 GPIO
[ 0.099967] pci 0000:00:1f.1: reg 10: [io 0xdd80-0xdd87]
[ 0.099985] pci 0000:00:1f.1: reg 14: [io 0xdd00-0xdd03]
[ 0.100017] pci 0000:00:1f.1: reg 18: [io 0xdc80-0xdc87]
[ 0.100035] pci 0000:00:1f.1: reg 1c: [io 0xdc00-0xdc03]
[ 0.100053] pci 0000:00:1f.1: reg 20: [io 0xdb80-0xdb8f]
[ 0.100071] pci 0000:00:1f.1: reg 24: [mem 0xfe977800-0xfe977bff]
[ 0.100168] pci 0000:00:1f.3: reg 20: [io 0x0400-0x041f]
[ 0.100272] pci 0000:01:0c.0: reg 10: [mem 0xfebffc00-0xfebffc7f]
[ 0.100290] pci 0000:01:0c.0: reg 14: [io 0xef80-0xefff]
[ 0.100308] pci 0000:01:0c.0: reg 18: [mem 0xfebc0000-0xfebdffff]
[ 0.100327] pci 0000:01:0c.0: reg 1c: [mem 0xfeba0000-0xfebbffff]
[ 0.100345] pci 0000:01:0c.0: reg 20: [mem 0xfea00000-0xfeafffff]
[ 0.100363] pci 0000:01:0c.0: reg 24: [mem 0xfeb80000-0xfeb9ffff]
[ 0.100426] pci 0000:01:0d.0: reg 10: [mem 0xfebfe000-0xfebfefff]
[ 0.100444] pci 0000:01:0d.0: reg 14: [io 0xef00-0xef3f]
[ 0.100461] pci 0000:01:0d.0: reg 18: [mem 0xfeb60000-0xfeb7ffff]
[ 0.100504] pci 0000:01:0d.0: reg 30: [mem 0xfebe0000-0xfebeffff pref]
[ 0.100533] pci 0000:01:0d.0: supports D1 D2
[ 0.100541] pci 0000:01:0d.0: PME# supported from D0 D1 D2 D3hot
[ 0.100551] pci 0000:01:0d.0: PME# disabled
[ 0.100596] pci 0000:01:0e.0: reg 10: [mem 0xfebfd000-0xfebfdfff]
[ 0.100614] pci 0000:01:0e.0: reg 14: [io 0xee80-0xeebf]
[ 0.100632] pci 0000:01:0e.0: reg 18: [mem 0xfeb40000-0xfeb5ffff]
[ 0.100675] pci 0000:01:0e.0: reg 30: [mem 0xfeb30000-0xfeb3ffff pref]
[ 0.100702] pci 0000:01:0e.0: supports D1 D2
[ 0.100710] pci 0000:01:0e.0: PME# supported from D0 D1 D2 D3hot
[ 0.100721] pci 0000:01:0e.0: PME# disabled
[ 0.100758] pci 0000:00:1e.0: PCI bridge to [bus 01-01] (subtractive decode)
[ 0.100826] pci 0000:00:1e.0: bridge window [io 0xe000-0xefff]
[ 0.100838] pci 0000:00:1e.0: bridge window [mem 0xfea00000-0xfebfffff]
[ 0.100851] pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.100862] pci 0000:00:1e.0: bridge window [io 0x0000-0xffff] (subtractive decode)
[ 0.100873] pci 0000:00:1e.0: bridge window [mem 0x00000000-0xffffffff] (subtractive decode)
[ 0.100892] pci_bus 0000:00: on NUMA node 0
[ 0.100903] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.101123] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.POP4._PRT]
[ 0.114017] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 0.114622] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 12 *14 15)
[ 0.116161] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 0.116750] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 *12 14 15)
[ 0.117340] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 *7 10 11 12 14 15)
[ 0.117929] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 *6 7 10 11 12 14 15)
[ 0.118519] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.120634] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 *15)
[ 0.121141] HEST: Table is not found!
[ 0.121356] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.121451] vgaarb: loaded
[ 0.121694] PCI: Using ACPI for IRQ routing
[ 0.121756] PCI: pci_cache_line_size set to 64 bytes
[ 0.121865] reserve RAM buffer: 000000000009fc00 - 000000000009ffff
[ 0.121875] reserve RAM buffer: 000000000f7f0000 - 000000000fffffff
[ 0.122214] Switching to clocksource tsc
[ 0.122865] pnp: PnP ACPI init
[ 0.122966] ACPI: bus type pnp registered
[ 0.130306] pnp: PnP ACPI: found 15 devices
[ 0.130367] ACPI: ACPI bus type pnp unregistered
[ 0.130430] PnPBIOS: Disabled by ACPI PNP
[ 0.130514] system 00:01: [mem 0xfeff0000-0xfeffffff] has been reserved
[ 0.130594] system 00:08: [io 0x0290-0x029f] has been reserved
[ 0.130666] system 00:09: [io 0x04d0-0x04d1] has been reserved
[ 0.130730] system 00:09: [io 0x0800-0x087f] has been reserved
[ 0.130793] system 00:09: [io 0x0480-0x04bf] has been reserved
[ 0.130865] system 00:0b: [mem 0xffc00000-0xffefffff] has been reserved
[ 0.130938] system 00:0d: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.131004] system 00:0d: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.131077] system 00:0e: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.131143] system 00:0e: [mem 0x000c0000-0x000cffff] could not be reserved
[ 0.131209] system 00:0e: [mem 0x000e0000-0x000fffff] could not be reserved
[ 0.131275] system 00:0e: [mem 0x00100000-0x0f7fffff] could not be reserved
[ 0.171194] pci 0000:00:1e.0: PCI bridge to [bus 01-01]
[ 0.171262] pci 0000:00:1e.0: bridge window [io 0xe000-0xefff]
[ 0.171330] pci 0000:00:1e.0: bridge window [mem 0xfea00000-0xfebfffff]
[ 0.171395] pci 0000:00:1e.0: bridge window [mem pref disabled]
[ 0.171475] pci 0000:00:1e.0: setting latency timer to 64
[ 0.171487] pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
[ 0.171497] pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
[ 0.171507] pci_bus 0000:01: resource 0 [io 0xe000-0xefff]
[ 0.171516] pci_bus 0000:01: resource 1 [mem 0xfea00000-0xfebfffff]
[ 0.171526] pci_bus 0000:01: resource 4 [io 0x0000-0xffff]
[ 0.171535] pci_bus 0000:01: resource 5 [mem 0x00000000-0xffffffff]
[ 0.171632] NET: Registered protocol family 2
[ 0.171861] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.172541] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.172736] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.172923] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.172984] TCP reno registered
[ 0.173040] UDP hash table entries: 128 (order: 0, 4096 bytes)
[ 0.173113] UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
[ 0.173387] NET: Registered protocol family 1
[ 0.173488] pci 0000:00:02.0: Boot video device
[ 0.173624] pci 0000:01:0d.0: Firmware left e100 interrupts enabled; disabling
[ 0.173739] pci 0000:01:0e.0: Firmware left e100 interrupts enabled; disabling
[ 0.173821] PCI: CLS 32 bytes, default 64
[ 0.173933] Unpacking initramfs...
[ 0.984899] Freeing initrd memory: 7232k freed
[ 0.994232] audit: initializing netlink socket (disabled)
[ 0.994322] type=2000 audit(1287003915.992:1): initialized
[ 1.030355] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 1.035888] VFS: Disk quotas dquot_6.5.2
[ 1.036145] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.036479] msgmni has been set to 480
[ 1.037156] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.037236] io scheduler noop registered
[ 1.037291] io scheduler deadline registered
[ 1.037387] io scheduler cfq registered (default)
[ 1.038095] ERST: Table is not found!
[ 1.038176] isapnp: Scanning for PnP cards...
[ 1.392302] isapnp: No Plug & Play device found
[ 1.392771] Linux agpgart interface v0.103
[ 1.393046] agpgart-intel 0000:00:00.0: Intel 855GM Chipset
[ 1.393484] agpgart-intel 0000:00:00.0: detected 8060K stolen memory
[ 1.395357] agpgart-intel 0000:00:00.0: AGP aperture is 128M @ 0xf0000000
[ 1.395614] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.416067] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.436518] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.457509] 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.478067] 00:07: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.478844] PNP: No PS/2 controller found. Probing ports directly.
[ 1.481227] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.481296] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.481681] mice: PS/2 mouse device common for all mice
[ 1.481848] rtc_cmos 00:03: RTC can wake from S4
[ 1.482031] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 1.482120] rtc0: alarms up to one month, y3k, 114 bytes nvram
[ 1.482212] cpuidle: using governor ladder
[ 1.482268] cpuidle: using governor menu
[ 1.483204] TCP cubic registered
[ 1.483723] NET: Registered protocol family 10
[ 1.485034] lo: Disabled Privacy Extensions
[ 1.485860] Mobile IPv6
[ 1.485914] NET: Registered protocol family 17
[ 1.485979] Registering the dns_resolver key type
[ 1.486102] Using IPI No-Shortcut mode
[ 1.486405] PM: Resume from disk failed.
[ 1.486431] registered taskstats version 1
[ 1.486915] rtc_cmos 00:03: setting system clock to 2010-10-13 21:05:17 UTC (1287003917)
[ 1.487076] Initalizing network drop monitor service
[ 1.487233] Freeing unused kernel memory: 388k freed
[ 1.487832] Write protecting the kernel text: 2572k
[ 1.487958] Write protecting the kernel read-only data: 944k
[ 1.712360] udevd (60): /proc/60/oom_adj is deprecated, please use /proc/60/oom_score_adj instead.
[ 3.424694] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
[ 3.424763] e100: Copyright(c) 1999-2006 Intel Corporation
[ 3.424911] e100 0000:01:0d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 3.448870] e100 0000:01:0d.0: PME# disabled
[ 3.825624] e100 0000:01:0d.0: eth0: addr 0xfebfe000, irq 20, MAC addr 00:80:82:62:0c:3d
[ 3.825770] e100 0000:01:0e.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 3.849730] e100 0000:01:0e.0: PME# disabled
[ 4.069552] usbcore: registered new interface driver usbfs
[ 4.070055] usbcore: registered new interface driver hub
[ 4.092179] usbcore: registered new device driver usb
[ 4.165477] uhci_hcd: USB Universal Host Controller Interface driver
[ 4.165666] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 4.165743] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 4.165754] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 4.165881] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 4.166020] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000df00
[ 4.166170] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.166235] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.166311] usb usb1: Product: UHCI Host Controller
[ 4.166370] usb usb1: Manufacturer: Linux 2.6.36-rc6-686 uhci_hcd
[ 4.166432] usb usb1: SerialNumber: 0000:00:1d.0
[ 4.176276] hub 1-0:1.0: USB hub found
[ 4.176780] hub 1-0:1.0: 2 ports detected
[ 4.177029] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 4.177104] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 4.177114] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 4.177196] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[ 4.177328] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000de80
[ 4.177468] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.177533] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.177609] usb usb2: Product: UHCI Host Controller
[ 4.177668] usb usb2: Manufacturer: Linux 2.6.36-rc6-686 uhci_hcd
[ 4.177729] usb usb2: SerialNumber: 0000:00:1d.1
[ 4.184031] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.184100] Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
[ 4.188292] hub 2-0:1.0: USB hub found
[ 4.188360] hub 2-0:1.0: 2 ports detected
[ 4.188619] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 4.188695] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 4.188705] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 4.188781] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[ 4.188916] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000de00
[ 4.189059] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.189124] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.189201] usb usb3: Product: UHCI Host Controller
[ 4.189260] usb usb3: Manufacturer: Linux 2.6.36-rc6-686 uhci_hcd
[ 4.189321] usb usb3: SerialNumber: 0000:00:1d.2
[ 4.189961] hub 3-0:1.0: USB hub found
[ 4.190028] hub 3-0:1.0: 2 ports detected
[ 4.190272] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23
[ 4.190368] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 4.190378] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 4.190454] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
[ 4.190579] ehci_hcd 0000:00:1d.7: debug port 1
[ 4.194528] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 4.212647] e100 0000:01:0e.0: eth1: addr 0xfebfd000, irq 21, MAC addr 00:80:82:62:0c:3e
[ 4.233212] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfe977c00
[ 4.249030] SCSI subsystem initialized
[ 4.280039] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 4.280186] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.280252] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.280329] usb usb4: Product: EHCI Host Controller
[ 4.280388] usb usb4: Manufacturer: Linux 2.6.36-rc6-686 ehci_hcd
[ 4.280449] usb usb4: SerialNumber: 0000:00:1d.7
[ 4.281178] hub 4-0:1.0: USB hub found
[ 4.281246] hub 4-0:1.0: 6 ports detected
[ 4.581920] libata version 3.00 loaded.
[ 4.599436] ata_piix 0000:00:1f.1: version 2.13
[ 4.599473] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 4.599621] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 4.599753] scsi0 : ata_piix
[ 4.600291] scsi1 : ata_piix
[ 4.605734] ata1: PATA max UDMA/100 cmd 0xdd80 ctl 0xdd00 bmdma 0xdb80 irq 18
[ 4.605802] ata2: PATA max UDMA/100 cmd 0xdc80 ctl 0xdc00 bmdma 0xdb88 irq 18
[ 4.784288] ata1.00: ATA-0: CF CARD 4GB, Ver2.22K, max UDMA/100
[ 4.784357] ata1.00: 7880544 sectors, multi 0: LBA
[ 4.784431] ata1.01: ATA-6: 512MB ATA Flash Disk, ADMA428M, max MWDMA2
[ 4.784495] ata1.01: 1000944 sectors, multi 0: LBA
[ 4.784562] ata1.00: limited to UDMA/33 due to 40-wire cable
[ 4.792176] ata1.00: configured for UDMA/33
[ 4.800311] ata1.01: configured for MWDMA2
[ 4.816211] ata1.00: configured for UDMA/33
[ 4.824310] ata1.01: configured for MWDMA2
[ 4.824371] ata1: EH complete
[ 4.824706] scsi 0:0:0:0: Direct-Access ATA CF CARD 4GB Ver2 PQ: 0 ANSI: 5
[ 4.825633] scsi 0:0:1:0: Direct-Access ATA 512MB ATA Flash ADMA PQ: 0 ANSI: 5
[ 4.872051] usb 2-2: new low speed USB device using uhci_hcd and address 2
[ 4.944377] sd 0:0:0:0: [sda] 7880544 512-byte logical blocks: (4.03 GB/3.75 GiB)
[ 4.944632] sd 0:0:0:0: [sda] Write Protect is off
[ 4.944694] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.944772] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 4.946788] sd 0:0:1:0: [sdb] 1000944 512-byte logical blocks: (512 MB/488 MiB)
[ 4.947037] sd 0:0:1:0: [sdb] Write Protect is off
[ 4.947098] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 4.947176] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.947684] sda: sda1 sda2
[ 4.948346] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 4.948415] ata1.01: BMDMA stat 0x64
[ 4.948475] ata1.01: failed command: READ DMA
[ 4.948548] ata1.01: cmd c8/00:08:00:00:00/00:00:00:00:00/f0 tag 0 dma 4096 in
[ 4.948553] res d0/d0:d0:d0:d0:d0/00:00:00:00:00/d0 Emask 0x2 (HSM violation)
[ 4.948700] ata1.01: status: { Busy }
[ 4.948757] ata1.01: error: { ICRC UNC IDNF }
[ 4.948859] ata1: soft resetting link
[ 5.058255] usb 2-2: New USB device found, idVendor=173d, idProduct=0004
[ 5.058325] usb 2-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 5.136192] ata1.00: configured for UDMA/33
[ 5.144322] ata1.01: configured for MWDMA2
[ 5.160299] ata1.00: configured for UDMA/33
[ 5.195410] ata1.01: configured for MWDMA2
[ 5.195489] ata1: EH complete
[ 5.196501] sdb: sdb1 sdb2 sdb3
[ 5.198217] sda: detected capacity change from 0 to 4034838528
[ 5.198373] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.199093] sdb: detected capacity change from 0 to 512483328
[ 5.199547] sda: detected capacity change from 0 to 4034838528
[ 5.199912] sd 0:0:1:0: [sdb] Attached SCSI disk
[ 5.207048] sdb: detected capacity change from 0 to 512483328
[ 5.247838] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 5.247912] ata1.01: BMDMA stat 0x64
[ 5.247973] ata1.01: failed command: READ DMA
[ 5.248088] ata1.01: cmd c8/00:08:00:45:0f/00:00:00:00:00/f0 tag 0 dma 4096 in
[ 5.248093] res d0/d0:d0:d0:d0:d0/00:00:00:00:00/d0 Emask 0x2 (HSM violation)
[ 5.248240] ata1.01: status: { Busy }
[ 5.248297] ata1.01: error: { ICRC UNC IDNF }
[ 5.248400] ata1: soft resetting link
[ 5.259432] usbcore: registered new interface driver hiddev
[ 5.293676] input: HID 173d:0004 as /devices/pci0000:00/0000:00:1d.1/usb2/2-2/2-2:1.0/input/input0
[ 5.294018] generic-usb 0003:173D:0004.0001: input,hidraw0: USB HID v1.10 Keyboard [HID 173d:0004] on usb-0000:00:1d.1-2/input0
[ 5.304032] usb 3-2: new low speed USB device using uhci_hcd and address 2
[ 5.373618] input: HID 173d:0004 as /devices/pci0000:00/0000:00:1d.1/usb2/2-2/2-2:1.1/input/input1
[ 5.374550] generic-usb 0003:173D:0004.0002: input,hiddev0,hidraw1: USB HID v1.10 Device [HID 173d:0004] on usb-0000:00:1d.1-2/input1
[ 5.375061] usbcore: registered new interface driver usbhid
[ 5.375123] usbhid: USB HID core driver
[ 5.436182] ata1.00: configured for UDMA/33
[ 5.444312] ata1.01: configured for MWDMA2
[ 5.460183] ata1.00: configured for UDMA/33
[ 5.468317] ata1.01: configured for MWDMA2
[ 5.468388] ata1: EH complete
[ 5.471906] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 5.471972] ata1.01: BMDMA stat 0x64
[ 5.472055] ata1.01: failed command: READ DMA
[ 5.472129] ata1.01: cmd c8/00:08:e0:45:0f/00:00:00:00:00/f0 tag 0 dma 4096 in
[ 5.472134] res d0/d0:d0:d0:d0:d0/00:00:00:00:00/d0 Emask 0x2 (HSM violation)
[ 5.472280] ata1.01: status: { Busy }
[ 5.472337] ata1.01: error: { ICRC UNC IDNF }
[ 5.472437] ata1: soft resetting link
[ 5.478736] usb 3-2: New USB device found, idVendor=093a, idProduct=2510
[ 5.478802] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 5.478866] usb 3-2: Product: USB OPTICAL MOUSE
[ 5.478924] usb 3-2: Manufacturer: PIXART
[ 5.508288] input: PIXART USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:1d.2/usb3/3-2/3-2:1.0/input/input2
[ 5.508824] generic-usb 0003:093A:2510.0003: input,hidraw2: USB HID v1.11 Mouse [PIXART USB OPTICAL MOUSE] on usb-0000:00:1d.2-2/input0
[ 5.660508] ata1.00: configured for UDMA/33
[ 5.668315] ata1.01: configured for MWDMA2
[ 5.684172] ata1.00: configured for UDMA/33
[ 5.692306] ata1.01: configured for MWDMA2
[ 5.692375] ata1: EH complete
[ 5.694977] ata1.01: limiting speed to MWDMA1:PIO4
[ 5.695043] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 5.695107] ata1.01: BMDMA stat 0x64
[ 5.695167] ata1.01: failed command: READ DMA
[ 5.695241] ata1.01: cmd c8/00:08:08:00:00/00:00:00:00:00/f0 tag 0 dma 4096 in
[ 5.695246] res d0/d0:d0:d0:d0:d0/00:00:00:00:00/d0 Emask 0x2 (HSM violation)
[ 5.695392] ata1.01: status: { Busy }
[ 5.695449] ata1.01: error: { ICRC UNC IDNF }
[ 5.695549] ata1: soft resetting link
[ 5.880173] ata1.00: configured for UDMA/33
[ 5.888321] ata1.01: configured for MWDMA1
[ 5.904312] ata1.00: configured for UDMA/33
[ 5.912320] ata1.01: configured for MWDMA1
[ 5.912387] ata1: EH complete
[ 5.914739] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 5.914805] ata1.01: BMDMA stat 0x64
[ 5.914865] ata1.01: failed command: READ DMA
[ 5.914938] ata1.01: cmd c8/00:08:e8:45:0f/00:00:00:00:00/f0 tag 0 dma 4096 in
[ 5.914943] res d0/d0:d0:d0:d0:d0/00:00:00:00:00/d0 Emask 0x2 (HSM violation)
[ 5.915089] ata1.01: status: { Busy }
[ 5.915146] ata1.01: error: { ICRC UNC IDNF }
[ 5.968022] ata1: soft resetting link
[ 6.156172] ata1.00: configured for UDMA/33
[ 6.164317] ata1.01: configured for MWDMA1
[ 6.180171] ata1.00: configured for UDMA/33
[ 6.188320] ata1.01: configured for MWDMA1
[ 6.188384] ata1: EH complete
[ 6.190978] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 6.191043] ata1.01: BMDMA stat 0x64
[ 6.191102] ata1.01: failed command: READ DMA
[ 6.191175] ata1.01: cmd c8/00:08:e8:44:0f/00:00:00:00:00/f0 tag 0 dma 4096 in
[ 6.191180] res d0/d0:d0:d0:d0:d0/00:00:00:00:00/d0 Emask 0x2 (HSM violation)
[ 6.191326] ata1.01: status: { Busy }
[ 6.191384] ata1.01: error: { ICRC UNC IDNF }
[ 6.191481] ata1: soft resetting link
[ 6.376173] ata1.00: configured for UDMA/33
[ 6.384319] ata1.01: configured for MWDMA1
[ 6.400171] ata1.00: configured for UDMA/33
[ 6.408319] ata1.01: configured for MWDMA1
[ 6.408385] ata1: EH complete
[ 6.411201] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 6.411268] ata1.01: BMDMA stat 0x64
[ 6.411327] ata1.01: failed command: READ DMA
[ 6.411400] ata1.01: cmd c8/00:08:b0:45:0f/00:00:00:00:00/f0 tag 0 dma 4096 in
[ 6.411405] res d0/d0:d0:d0:d0:d0/00:00:00:00:00/d0 Emask 0x2 (HSM violation)
[ 6.411552] ata1.01: status: { Busy }
[ 6.411609] ata1.01: error: { ICRC UNC IDNF }
[ 6.411707] ata1: soft resetting link
[ 6.596174] ata1.00: configured for UDMA/33
[ 6.604319] ata1.01: configured for MWDMA1
[ 6.620174] ata1.00: configured for UDMA/33
[ 6.628321] ata1.01: configured for MWDMA1
[ 6.628386] ata1: EH complete
[ 6.629816] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 6.629881] ata1.01: BMDMA stat 0x64
[ 6.629939] ata1.01: failed command: READ DMA
[ 6.630012] ata1.01: cmd c8/00:08:b0:45:0f/00:00:00:00:00/f0 tag 0 dma 4096 in
[ 6.630017] res d0/d0:d0:d0:d0:d0/00:00:00:00:00/d0 Emask 0x2 (HSM violation)
[ 6.630162] ata1.01: status: { Busy }
[ 6.630219] ata1.01: error: { ICRC UNC IDNF }
[ 6.684022] ata1: soft resetting link
[ 6.872177] ata1.00: configured for UDMA/33
[ 6.880320] ata1.01: configured for MWDMA1
[ 6.896172] ata1.00: configured for UDMA/33
[ 6.904319] ata1.01: configured for MWDMA1
[ 6.904384] ata1: EH complete
[ 6.905808] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 6.905873] ata1.01: BMDMA stat 0x64
[ 6.905933] ata1.01: failed command: READ DMA
[ 6.906006] ata1.01: cmd c8/00:08:b0:45:0f/00:00:00:00:00/f0 tag 0 dma 4096 in
[ 6.906011] res d0/d0:d0:d0:d0:d0/00:00:00:00:00/d0 Emask 0x2 (HSM violation)
[ 6.906157] ata1.01: status: { Busy }
[ 6.906214] ata1.01: error: { ICRC UNC IDNF }
[ 6.960021] ata1: soft resetting link
[ 7.148172] ata1.00: configured for UDMA/33
[ 7.156323] ata1.01: configured for MWDMA1
[ 7.172182] ata1.00: configured for UDMA/33
[ 7.180317] ata1.01: configured for MWDMA1
[ 7.180383] ata1: EH complete
[ 7.181871] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 7.181937] ata1.01: BMDMA stat 0x64
[ 7.181996] ata1.01: failed command: READ DMA
[ 7.182069] ata1.01: cmd c8/00:08:b0:45:0f/00:00:00:00:00/f0 tag 0 dma 4096 in
[ 7.182074] res d0/d0:d0:d0:d0:d0/00:00:00:00:00/d0 Emask 0x2 (HSM violation)
[ 7.182220] ata1.01: status: { Busy }
[ 7.182277] ata1.01: error: { ICRC UNC IDNF }
[ 7.182374] ata1: soft resetting link
[ 7.368173] ata1.00: configured for UDMA/33
[ 7.376324] ata1.01: configured for MWDMA1
[ 7.392172] ata1.00: configured for UDMA/33
[ 7.400314] ata1.01: configured for MWDMA1
[ 7.400379] ata1: EH complete
[ 7.401963] ata1.01: limiting speed to PIO4
[ 7.402027] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 7.402091] ata1.01: BMDMA stat 0x64
[ 7.402150] ata1.01: failed command: READ DMA
[ 7.402223] ata1.01: cmd c8/00:08:b0:45:0f/00:00:00:00:00/f0 tag 0 dma 4096 in
[ 7.402228] res d0/d0:d0:d0:d0:d0/00:00:00:00:00/d0 Emask 0x2 (HSM violation)
[ 7.402374] ata1.01: status: { Busy }
[ 7.402431] ata1.01: error: { ICRC UNC IDNF }
[ 7.402528] ata1: soft resetting link
[ 7.588173] ata1.00: configured for UDMA/33
[ 7.596309] ata1.01: configured for PIO4
[ 7.612172] ata1.00: configured for UDMA/33
[ 7.620305] ata1.01: configured for PIO4
[ 7.620370] ata1: EH complete
[ 7.660296] sdb: detected capacity change from 0 to 512483328
[ 8.904373] udev: starting version 161
[ 14.180742] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 14.196180] intel_rng: FWH not detected
[ 14.413282] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 14.686229] udev: renamed network interface eth0 to eth0-eth1
[ 14.690043] udev: renamed network interface eth1 to eth2
[ 14.738112] udev: renamed network interface eth0-eth1 to eth1
[ 14.785281] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 14.853901] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input3
[ 14.854240] ACPI: Power Button [PWRB]
[ 14.854621] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 14.854901] ACPI: Power Button [PWRF]
[ 15.561686] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 15.772037] Error: Driver 'pcspkr' is already registered, aborting...
[ 16.341384] [drm] Initialized drm 1.1.0 20060810
[ 17.184744] ACPI: acpi_idle registered with cpuidle
[ 18.406605] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 18.406682] i915 0000:00:02.0: setting latency timer to 64
[ 18.520076] [drm] set up 7M of stolen space
[ 19.057483] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 19.058254] [drm] initialized overlay support
[ 23.580563] Console: switching to colour frame buffer device 128x48
[ 23.593712] fb0: inteldrmfb frame buffer device
[ 23.593718] drm: registered panic notifier
[ 23.593983] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 23.796499] EXT2-fs (sda1): warning: mounting unchecked fs, running e2fsck is recommended
[ 24.736328] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 24.740303] e100 0000:01:0d.0: eth1: NIC Link is Up 100 Mbps Full Duplex
[ 24.740711] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
Reply to: